Tuning interfacial charge dynamics in 2D SnO2–MWCNT composite photoanodes for dye-sensitized solar cells
Source abstract
Abstract
This paper presents a low-temperature, facile, and cost-effective wet chemical synthesis of two-dimensional (2D) tin oxide (SnO2)–multi-walled carbon nanotube (MWCNT) composites for efficient dye-sensitized solar cells (DSSCs). Incorporating varying concentrations of MWCNTs into 2D SnO2 nanosheets significantly enhanced the overall photovoltaic performance by improving charge separation and suppressing electron–hole recombination. The 2D SnO2–MWCNT composites exhibited remarkable photoluminescence quenching and increased UV-vis absorbance, indicating efficient photoinduced charge transfer. The optimized 2D SnO2–MWCNT composite photoanode achieved a power conversion efficiency (PCE) of 3.84%, which was ~ 3.5 times higher than that of the pristine SnO2 nanosheets (1.83%). This PCE improvement was attributed to an increase in the short-circuit current density (Jsc) and the fill factor (FF). Additionally, electrochemical impedance spectroscopy (EIS) measurements confirmed the reduced charge transport resistance, increased electron diffusion length, enhanced charge collection efficiency, and enhanced electron mobility of the 2D SnO2–MWCNT composites. This improved photovoltaic performance is primarily attributed to the incorporation of MWCNTs, which provide efficient electron-conducting pathways that mitigate recombination. These results highlight the potential of 2D SnO2–MWCNT composites as efficient photoanodes for DSSCs, providing valuable insights into the interfacial charge dynamics of next-generation optoelectronic devices.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: TiO2 Photocatalysis and Solar Cells · Advanced Photocatalysis Techniques · Gas Sensing Nanomaterials and Sensors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (61)
Show source-provided references
1. Ballif C, Haug F-J, Boccard M, Verlinden PJ, Hahn G (2022) Status and perspectives of crystalline silicon photovoltaics in research and industry. Nat Rev Mater 7:597–61610.1038/s41578-022-00423-2 ↗
2. Zeng L, Bermel P, Yi Y, Alamariu BA, Broderick KA, Liu J, Hong C, Duan X, Joannopoulos J, Kimerling LC (2008) Demonstration of enhanced absorption in thin-film Si solar cells with textured photonic crystal back reflector. Appl Phys Lett 93:22110510.1063/1.3039787 ↗
3. Green MA (1982) Solar cells: Operating principles, technology, and system applications. Englewood Cliffs, NJ, Prentice-Hall, Inc., p 288
4. Liu Z, Sofia SE, Laine HS, Woodhouse M, Wieghold S, Petersa IM, Buonassisi T (2020) Revisiting thin silicon for photovoltaics: a technoeconomic perspective. Energy Environ Sci 13:12–2310.1039/C9EE02452B ↗
5. O´Regan B, Grätzel M (1991) A low-cost high-efficiency solar cell based on dye-sensitized colloidal TiO2 films. Nature 353:73710.1038/353737a0 ↗
6. Mathew S, Yella A, Gao P, Humphry-Baker R, Curchod BFE, Ashari-Astani N, Tavernelli I, Rothlisberger U, Nazeeruddin MK, Grätzel M (2014) Dye-sensitized solar cells with 13% efficiency achieved through the molecular engineering of porphyrin sensitizers. Nat Chem 6:242–24710.1038/nchem.1861 ↗
7. Qian J, Liu P, Xiao Y, Jiang Y, Cao Y, Ai X, Yang H (2009) TiO2-coated multilayered SnO2 hollow microspheres for dye-sensitized solar cells. Adv Mater 21:3663–366710.1002/adma.200900525 ↗
8. Ambade SB, Ambade RB, Mane RS, Lee G-W, Shaikh SF, Patil SA, Joo O-S, Han S-H, Lee S-H (2013) Low temperature chemically synthesized rutile TiO2 photoanodes with high electron lifetime for organic dye-sensitized solar cells. Chem Commun 49:2921–292310.1039/c3cc00310h ↗
9. Lee G-W, Ambade SB, Cho Y-J, Mane RS, Shashikala V, Yadav J, Gaikwad RS, Lee S-H, Jung K-D, Han S-H (2010) Stereospecific growth of densely populated rutile mesoporous TiO2 nanoplate films: a facile low temperature chemical synthesis approach. Nanotechnology 21:10560310.1088/0957-4484/21/10/105603 ↗
10. Ambade SB, Mane RS, Ghule AV, Lee G-W, Sharma R, Joo O-S, Ambade RB, Lee S-H, Han S-H (2011) A simple CdS nanoparticles cascading approach for boosting N3 dye/ZnO nanoplates DSSCs overall performance. J Photochem Photobiol Chem 217:267–27010.1016/j.jphotochem.2010.09.023 ↗
11. Mane RS, Lee WJ, Pathan HM, Han S-H (2005) Nanocrystalline TiO2/ZnO thin films: Fabrication and application to dye-sensitized solar cells. J Phys Chem B 109:24254–2425910.1021/jp0531560 ↗
12. Zhang Q, Dandeneau CS, Zhou X, Cao G (2009) ZnO nanostructures for dye-sensitized solar cells. Adv Mater 21:4087–410810.1002/adma.200803827 ↗
13. Gubbala S, Chakrapani V, Kumar V, Sunkara MK (2008) Band-edge engineered hybrid structures for dye-sensitized solar cells based on SnO2 nanowires. Adv Funct Mater 18:2411–241810.1002/adfm.200800099 ↗
14. Chappel S, Zaban A (2002) Nanoporous SnO2 electrodes for dye-sensitized solar cells: improved cell performance by the synthesis of 18 nm SnO2 colloids. Sol Energ Mat Sol Cells 71:141–15210.1016/S0927-0248(01)00050-2 ↗
15. Kavan L, Zivcova ZV, Zlamalova M, Zakeeruddin SM, Grätzel M (2020) Electron-selective layers for dye-sensitized solar cells based on TiO2 and SnO2. J Phys Chem C 124:6512–652110.1021/acs.jpcc.9b11883 ↗
16. Gong X, Beedri NI, Abou Taleb MF, Ibrahim MM, Sayyed SAAR, Pathan HM, Hou H, Algadi H, Salunke-Gawali S, Ma Y (2023) An overview of bi-layered niobium pentoxide (Nb2O5)-based photoanodes for dye-sensitized solar cells. Adv Compos Hybrid Mater 6:21310.1007/s42114-023-00791-5 ↗
17. Chen SG, Chappel S, Diamant Y, Zaban A (2001) Preparation of Nb2O5 coated TiO2 nanoporous electrodes and their application in dye-sensitized solar cells. Chem Mater 13:4629–463410.1021/cm010343b ↗
18. Ghosh R, Brennaman MK, Uher T, Ok M-R, Samulski ET, McNeil LE, Meyer TJ, Lopez R (2011) Nanoforest Nb2O5 photoanodes for dye-sensitized solar cells by pulsed laser deposition. ACS Appl Mater Interfaces 3:3929–393510.1021/am200805x ↗
19. Harish V, Ansari MM, Tewari D, Gaur M, Yadav AB, Betancourt M-LG, Abdel- M, Haleem M, Bechelany A, Barhoum (2022) Nanoparticle and nanostructure synthesis and controlled growth methods. Nanomaterials 12:322610.3390/nano12183226 ↗
20. Desai UV, Xu C, Wu J, Gao D (2013) Hybrid TiO2–SnO2 nanotube arrays for dye-sensitized solar cells. J Phys Chem C 117:3232–323910.1021/jp3096727 ↗
21. Yang G, Yan Z, Xiao T (2012) Preparation and characterization of SnO2/ZnO/TiO2 composite semiconductor with enhanced photocatalytic activity. Appl Surf Sci 258:8704–871210.1016/j.apsusc.2012.05.078 ↗
22. Nosaka Y, Nosaka AY (2016) Reconsideration of intrinsic band alignments within anatase and rutile TiO2. J Phys Chem Lett 7:431–43410.1021/acs.jpclett.5b02804 ↗
23. Chou TP, Zhang Q, Cao G (2007) Effects of dye loading conditions on the energy conversion efficiency of ZnO and TiO2dye-sensitized solar cells. J Phys Chem C 111:18804–1881110.1021/jp076724f ↗
24. Vinodgopal K, Kamat PV (1995) Enhanced rates of photocatalytic degradation of an azo dye using SnO2/TiO2coupled semiconductor thin films. Environ Sci Technol 29:841–84510.1021/es00003a037 ↗
25. Lee ABY-G, Koll D, Meerbeek XV, Frank S, Choi MJ, Kang YS, Char K (2012) W.Tremel, Highly efficient and stable dye-sensitized solar cells based on SnO2 nanocrystals prepared by microwave-assisted synthesis. Energy Environ Sci 5:5392–540010.1039/C1EE02115J ↗
26. Lee J-H, Park N-G, Shin Y-J (2011) Nano-grain SnO2 electrodes for high conversion efficiency SnO2–DSSC. Sol Eng Mater Sol Cells 95:17910.1016/j.solmat.2010.04.027 ↗
27. Ramasamy E, Lee J (2010) Ordered mesoporous SnO2–based photoanodes for high-performance dye-sensitized solar cells. J Phys Chem C 114:2203210.1021/jp1074797 ↗
28. Bhande SS, Taur GA, Shaikh AV, Joo O-S, Sung M-M, Mane RS, Ghule AV, Han S-H (2012) Structural analysis and dye-sensitized solar cell application of electrodeposited tin oxide nanoparticles. Mater Lett 79:2910.1016/j.matlet.2012.03.074 ↗
29. Bhande SS, Gaikwad SL, Pawar BG, Shaikh AV, Kolekar SS, Joo O-S, Mane RS, Han S-H (2013) Photoelectrochemical studies of chemically (sol–gel) synthesized tin oxide nanocrystallites. J Nanoengg Nanomanufact 3:237–24210.1166/jnan.2013.1138 ↗
30. Pang H, Yang HB, Guo CX, Li CM (2012) Functionalization of SnO₂ photoanode through Mg-doping and TiO₂-coating to synergically boost dye-sensitized solar cell performance. ACS Appl Mater Interfaces 4:6261–626510.1021/am3018493 ↗
31. Kim M-H, Kwon Y-U (2009) Semiconductor CdO as a blocking layer material on DSSC electrode: mechanism and application. J Phys Chem C 113:17176–1718210.1021/jp904206a ↗
32. Park N-G, Kang MG, Ryu KS, Kim KM (2004) Photovoltaic characteristics of dye-sensitized surface-modified nanocrystalline SnO2 solar cells. J Photochem Photobiol Chem 161:105–11010.1016/S1010-6030(03)00280-6 ↗
33. Li Z, Zhou Y, Yu T, Liu J, Zou Z (2012) Unique Zn-doped SnO2 nano-echinus with excellent electron transport and light harvesting properties as photoanode materials for high performance dye-sensitized solar cell. CrystEngComm 14:6462–646810.1039/c2ce25954k ↗
34. Tan B, Toman E, Li Y, Wu Y (2007) Zinc stannate (Zn2SnO4) dye-sensitized solar cells. J Am Chem Soc 129:4162–416310.1021/ja070804f ↗
35. Chang W-C, Cheng Y-Y, Yu W-C, Yao Y-C, Lee C-H, Ko H-H (2012) Enhancing performance of ZnO DSSCs via acid-treatment and controlled loading of multi-walled carbon nanotubes. Nanoscale Res Lett 7:16610.1186/1556-276X-7-166 ↗
36. Yu H, Quan X, Chen S, Zhao H (2007) TiO2–multiwalled carbon nanotube heterojunction arrays and their charge separation capability. J Phys Chem C111:12987–12991
37. Li L, Yang M, Zhang S, Liu P, Li G, Wen W, Zhang H, Zhao H (2010) The fabrication of CNTs/TiO2 photoanodes for sensitive determination of organic compounds. Nanotechnology 21:48550310.1088/0957-4484/21/48/485503 ↗
38. Liu S, Yang L, Xu S, Luo S, Cai Q (2009) Photocatalytic activities of C–N-doped TiO2 nanotube array/carbon nanorod composite. Electrochem Commun 11:1748–175110.1016/j.elecom.2009.07.007 ↗
39. Yen C-Y, Lin Y-F, Liao S-H, Weng C-C, Huang C-C, Hsiao Y-H, Ma C-CM, Chang M-C, Shao H, Tsai M-C (2008) Preparation and properties of a carbon nanotube-based nanocomposite photoanode for dye-sensitized solar cells. Nanotechnology 19:37530510.1088/0957-4484/19/37/375305 ↗
40. Xu CL, Wei BQ, Ma RZ, Liang J, Ma XK, Wu DH (1999) Fabrication of aluminum–carbon nanotube composites and their electrical properties. Carbon 37:85510.1016/S0008-6223(98)00285-1 ↗
41. Niu JJ, Wang JN, Jiang Y, Su LF, Ma J (2007) An approach to carbon nanotubes with high surface area and large pore volume. Microporous Mesoporous Mater 100:110.1016/j.micromeso.2006.10.009 ↗
42. Chang PR, Zheng P, Liu B, Anderson DP, Yu J, Ma X (2011) Characterization of magnetic soluble starch-functionalized carbon nanotubes and its application for the adsorption of the dyes. J Hazard Mater 186:214410.1016/j.jhazmat.2010.12.119 ↗
43. Flahaut E, Peigney A, Laurent C, Marlière C, Chastel F, Rousset A (2000) Carbon nanotube–metal–oxide nanocomposites: microstructure, electrical conductivity and mechanical properties. Acta Mater 48:380310.1016/S1359-6454(00)00147-6 ↗
44. Chen C, Liang B, Ogino A, Wang X, Nagatsu M (2009) Oxygen functionalization of multiwall carbon nanotubes by microwave-excited surface-wave plasma treatment. J Phys Chem C 113:7659–766510.1021/jp9012015 ↗
45. Chang C-M, Liu Y-L (2010) Functionalization of multi-walled carbon nanotubes with non-reactive polymers through an ozone-mediated process for the preparation of a wide range of high performance polymer/carbon nanotube composites. Carbon 48:1289–129710.1016/j.carbon.2009.12.002 ↗
46. Balasubramanian K, Burghard M (2005) Chemically functionalized carbon nanotubes. Small 1:180–19210.1002/smll.200400118 ↗
47. Tao T, He L, Li J, Zhang Y (2015) A new way for synthesizing SnO2 nanosheets. Mater Lett 138:45–4710.1016/j.matlet.2014.09.112 ↗
48. Bhande SS, Ambade RB, Shinde DV, Ambade SB, Patil SA, Naushad M, Mane RS, Alothman ZA, Lee S-H, Han S-H (2015) Improved photoelectrochemical cell performance of tin oxide with functionalized multi-walled carbon nanotubes–cadmium selenide sensitizer. ACS Appl Mater Interfaces 7:25094–2510410.1021/acsami.5b05385 ↗
49. Li W, Yan C, Zhu Y, Tian H, Hu J, Iqbal A, Peisan E, Zai J, Qian X (2021) Morphology genetic 3D hierarchical SnO2 microstructures constructed by Sub 5 nm nanocrystals for highly sensitive ethanol-sensor. Nanotechnology 32:48550310.1088/1361-6528/ac2019 ↗
50. Tran V-H, Ambade RB, Ambade SB, Lee S-H, Lee I-H (2017) Low-temperature solution-processed SnO2 nanoparticles as a cathode buffer layer for inverted organic solar cells. ACS Appl Mater Interfaces 9:1645–165310.1021/acsami.6b10857 ↗
51. Ambade RB, Ambade SB, Mane RS, Lee S-H (2015) Interfacial engineering importance of bilayered ZnO cathode buffer on the photovoltaic performance of inverted organic solar cells. ACS Appl Mater Interfaces 7:7951–796010.1021/am509125c ↗
52. Ambade SB, Ambade RB, Lee W, Mane RS, Yoon SC, Lee S-H (2014) Development of highly transparent seedless ZnO nanorods engineered for inverted polymer solar cells. Nanoscale 6:12130–1214110.1039/C4NR03080J ↗
53. Ambade SB, Ambade RB, Bagde SS, Lee S-H (2016) Work-function and surface energy tunable cyanoacrylic acid small-molecule derivative interlayer on planar ZnO nanorods for improved organic photovoltaic performance. Appl Mater Interfaces 8:35270–3528010.1021/acsami.6b11865 ↗
54. Ambade RB, Lee H, Lee KH, Lee H, Veerasubramani GK, Kim Y-B, Han TH (2022) Ultrafast flashlight sintered mesoporous NiO nanosheets for stable asymmetric supercapacitors. Chem Eng J 436:13504110.1016/j.cej.2022.135041 ↗
55. Ambade RB, Veerasubramani GK, Ambade SB, Christy M, Eom W, Shin H, Kim Y-B, Kim D-W, Han TH (2021) Photonic split-second induced mesoporous TiO2-Graphene architectures for efficient sodium-ion batteries. Carbon 178:332–34410.1016/j.carbon.2021.03.028 ↗
56. Han L, Koide N, Chiba Y, Islam A, Komiya R, Fuke N, Fukui A, Yamanaka R (2005) Improvement of efficiency of dye-sensitized solar cells by reduction of internal resistance. Appl Phys Lett 86:21350110.1063/1.1925773 ↗
57. Wang Q, Moser J-E, Grätzel M (2005) Electrochemical impedance spectroscopic analysis of dye-sensitized solar cells. J Phys Chem B 109:14945–1495310.1021/jp052768h ↗
58. Kern R, Sastrawan R, Ferber J, Stangl R, Luther J (2002) Modeling and interpretation of electrical impedance spectra of dye solar cells operated under open-circuit conditions. Electrochim Acta 47:4213–422510.1016/S0013-4686(02)00444-9 ↗
59. Adachi M, Sakamoto M, Jiu J, Ogata Y, Isoda S (2006) Determination of parameters of electron transport in dye-sensitized solar cells using electrochemical impedance spectroscopy. J Phys Chem B 110:13872–1388010.1021/jp061693u ↗
60. Han L, Koide N, Chiba Y, Mitate T (2004) Modeling of an equivalent circuit for dye-sensitized solar cells. Appl Phys Lett 84:2433–243510.1063/1.1690495 ↗
61. Bhande SS, Shinde DV, Shaikh SF, Ambade SB, Ambade RB, Mane RS, Inamuddin M, Naushad S-H, Han (2014) Low-temperature solution-processed Zn-doped SnO2 photoanodes: enhancements in charge collection efficiency and mobility. RSC Adv 4:20527–2053010.1039/C4RA01493F ↗