Engineering multiphase bismuth molybdate coatings via magnetron sputtering for highly stable photocatalysis
Source abstract
Abstract
The practical application of photocatalysis for wastewater treatment is frequently hindered by the limitations of post-treatment recovery from powder suspensions and by concentration-dependent kinetic decay. In this study, highly stable, supported bismuth molybdate (BMO) coatings were synthesized via dual-target reactive magnetron sputtering. By changing the power applied to the Mo target from 20 to 100 W, while keeping the power applied to the α-Bi 2 O 3 target fixed (30 W), the Bi/Mo stoichiometry was tuned from Bi-rich (Bi/Mo ∼ 5) to Mo-rich samples (Bi/Mo ∼ 0.5), and annealing at 500 °C drives the transition from amorphous states to crystalline BMO phases. The optimized t-BMO80 coating (Bi/Mo = 0.8) exhibited exceptional photocatalytic efficiency for the degradation of Indigo Carmine dye at pH of 3.5 under 385 nm irradiation (100 % discoloration in 120 min). Structural and electronic structure analyses revealed that this superior activity originates from the formation of a multiphase α-Bi 2 Mo 3 O 12 /MoO 3 architecture, establishing a robust Type-II staggered heterojunction. The experimentally determined band alignments (VB = +2.601 V and CB = -0.469 V vs. NHE) enable a synergistic, dual-pathway degradation mechanism driven by direct hole oxidation and the continuous generation of hydroperoxyl radicals in acid conditions, while the secondary MoO 3 phase acts as an efficient electron sink, suppressing charge recombination. Crucially, this spatial charge separation sustains a surface-saturated, zero-order kinetic regime by passing the pseudo-first-order rate limitations typical of BMO powders. The immobilized thin films on fused silica demonstrated structural integrity, maintaining a constant absolute degradation rate across ten consecutive reuse cycles (average k abs = 4.45 ± 0.85 × 10 −2 ppm min −1 ). These findings present a scalable, highly durable heterostructure architecture uniquely suited for continuous-flow advanced oxidation processes.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Photocatalysis Techniques · Polyoxometalates: Synthesis and Applications · Layered Double Hydroxides Synthesis and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (86)
Show source-provided references
1. Contamination of textile dyes in aquatic environment: adverse impacts on aquatic ecosystem and human health, and its management using bioremediation10.1016/j.jenvman.2024.120103 ↗
2. Environmental risks of textile dyes and photocatalytic materials for sustainable treatment: current status and future directions10.1007/s44274-025-00337-0 ↗
3. A critical review on textile dye-containing wastewater: ecotoxicity, health risks, and remediation strategies for environmental safety10.1016/j.clce.2025.100165 ↗
4. Methylene blue dye: Toxicity and potential elimination technology from wastewater10.1016/j.rineng.2022.100678 ↗
5. Rhodamine B, an organic environmental pollutant induces reproductive toxicity in parental and teratogenicity in F1 generation in vivo
6. Indigo carmine: between necessity and concern10.3390/jox13030033 ↗
7. Toxicity of malachite green on plants and its phytoremediation: a review
8. Exposure to Crystal Violet, Its Toxic
9. Adsorption of methyl orange: a review on adsorbent performance10.1016/j.crgsc.2021.100179 ↗
10. Intra-arterial dye method with vasomotors (PIAD Method) applied for the endoscopic diagnosis of gastric cancer and the side effects of indigo carmine10.1055/s-2007-1021597 ↗
11. Effects of some cosmetic dyes and pigments on the proliferation of human foreskin fibroblasts and cellular oxidative stress; potential cytotoxicity of chlorophyllin and indigo carmine on fibroblasts10.1111/jocd.14695 ↗
12. Photocatalytic dye degradation from textile wastewater: a review10.1021/acsomega.4c00887 ↗
13. Semiconductor photocatalysts: a critical review highlighting the various strategies to boost the photocatalytic performances for diverse applications10.1016/j.cis.2022.102830 ↗
14. Titanium dioxide (TiO2)-based photocatalyst materials activity enhancement for contaminants of emerging concern (CECs) degradation: in the light of modification strategies10.1016/j.ceja.2022.100262 ↗
15. Preparations and applications of zinc oxide based photocatalytic materials
16. Photocatalytic performance of Nd/TiO2 and Nb/TiO2 nanomaterials in the degradation of p -cresol at room temperature10.1002/jctb.7624 ↗
17. The influence of Nd3+ ions on the optical, photocatalytic properties, and surface morphology of thin mesoporous ZnO layers10.1002/adem.202502783 ↗
18. Non-metal doped ZnO and TiO2 photocatalysts for visible light active degradation of pharmaceuticals and hydrogen production: a review
19. Tetracycline degradation and hydrogen production over an interface-engineered double S-Scheme g-C3N4/TiO2 heterojunction photocatalyst10.1007/s42823-025-01022-1 ↗
20. Effective photodegradation of organic pollutants and antibacterial activity by TiO2/ZnO composite nanofibers as a direct Z-scheme heterojunction photocatalyst10.1016/j.jwpe.2025.108562 ↗
21. Lattice distortion in a confined structured ZnS/ZnO HETEROJUNCTION FOR EFFICIENT PHOTOCATALYTIC CO2 reduction10.1021/acsami.3c06889 ↗
22. Construction of CdS-BiCu2VO6 heterojunctions for enhanced visible-light-driven photocatalytic degradation of tetracycline and hydrogen evolution10.1016/j.jtice.2025.106476 ↗
23. A dual reduction-type semiconductor heterojunction of In2S3/C3N4 for improved photocatalytic hydrogen production under visible light10.1016/j.jallcom.2026.186085 ↗
24. Architectural engineering of yolk-shell TiO2@g-C3N4 S-scheme heterojunctions via a peroxidation strategy for enhanced photocatalytic hydrogen evolution10.1016/j.apsusc.2026.166680 ↗
25. Recent advances on Bismuth-based photocatalysts: strategies and mechanisms10.1016/j.cej.2021.129484 ↗
26. Phase diagram studies on ternary Bi–Mo–O system10.1016/j.jssc.2020.121657 ↗
27. Partial phase diagram of MoO3 rich section of the ternary Bi-Mo-O system10.1016/j.jallcom.2018.02.147 ↗
28. An overview on bismuth molybdate based photocatalytic systems: Controlled morphology and enhancement strategies for photocatalytic water purification10.1016/j.jece.2020.104291 ↗
29. Hydrothermal synthesis and photocatalytic properties of bismuth molybdate materials10.1016/j.matchemphys.2009.02.058 ↗
30. Bi2 MoO6 -based photocatalysts: engineering strategies for environmental and energy applications10.1039/D5RA05129K ↗
31. Towards understanding the photocatalytic activity enhancement of ordered mesoporous Bi2 MoO6 crystals prepared via a novel vacuum-assisted nanocasting method10.1039/C6RA05796A ↗
32. Photocatalytic removal of nitric oxide by Bi2Mo3O12 prepared by co-precipitation method10.1016/j.apcata.2013.09.013 ↗
33. Microwave-assisted hydrothermal synthesis, characterization and catalytic performance of α-Bi2Mo3O12 in the selective oxidation of propene10.1007/s11814-024-00176-4 ↗
34. Recent progress on bismuth-based materials for full-spectrum-driven photocatalysis10.1016/j.jece.2024.114790 ↗
35. Simple solvothermal routes to synthesize nanocrystalline Bi2MoO6 photocatalysts with different morphologies10.1016/j.actamat.2007.04.034 ↗
36. Bi2 MoO6 nanobelts for crystal facet‐enhanced photocatalysis10.1002/smll.201302950 ↗
37. One-dimensional Bi2MoO6 nanotubes: controllable synthesis by electrospinning and enhanced simulated sunlight photocatalytic degradation performances10.1007/s11051-015-3003-8 ↗
38. A facile mixed-solvothermal route to γ-Bi2MoO6 nanoflakes and their visible-light-responsive photocatalytic activity10.1016/j.materresbull.2013.05.104 ↗
39. Facile preparation of ultrathin Bi2MoO6 nanosheets for photocatalytic oxidation of toluene to benzaldehyde under visible light irradiation10.1016/j.jssc.2018.09.027 ↗
40. Microwave hydrothermal synthesis and visible-light photocatalytic activity of γ-Bi2MoO6 nanoplates10.1016/j.matchemphys.2008.02.008 ↗
41. Surface defect-mediated efficient electron-hole separation in hierarchical flower-like bismuth molybdate hollow spheres for enhanced visible-light-driven photocatalytic performance10.1016/j.jcis.2018.07.073 ↗
42. Preparation of γ-Bi2MoO6 thin films by thermal evaporation deposition and characterization for photocatalytic applications10.1016/j.cattod.2010.05.005 ↗
43. Deposition of visible light active photocatalytic bismuth molybdate thin films by reactive magnetron sputtering10.3390/ma9020067 ↗
44. Photocatalytic discoloration of methyl orange dye by δ-Bi2O3 thin films10.1016/j.tsf.2016.05.034 ↗
45. Stabilization of the delta-phase in Bi2O3 thin films10.1016/j.ssi.2013.12.027 ↗
46. Interpretation of the Raman spectra of bismuth oxide thin films presenting different crystallographic phases10.1016/j.jallcom.2020.157245 ↗
47. Dynamic XPS measurements on bismuth molybdate surfaces10.1016/0039-6028(96)00083-0 ↗
48. A study of in situ reduction of MoO3 to MoO2 by X-ray photoelectron spectroscopy10.1016/j.apsusc.2022.153827 ↗
49. Phase diagram of the system Bi2O3$z.sbnd; MoO310.1016/0021-9517(79)90279-3 ↗
50. One-step synthesis of bismuth molybdate catalysts via flame spray pyrolysis for the selective oxidation of propylene to acrolein10.1039/C4CC07527G ↗
51. In situ study of the formation of crystalline bismuth molybdate materials under hydrothermal conditions10.1021/cm020463z ↗
52. Influence of organic species on surface area of bismuth molybdate catalysts in complexation and spray drying methods10.1016/j.apcata.2004.03.007 ↗
53. M.T. Le, Bismuth Molybdate-Based Catalysts for Selective Oxidation of Hydrocarbons, in: Y. Zhou, F. Dong, S. Jin (Eds.), Bismuth - Advanced Applications and Defects Characterization, InTech, 2018. Doi: 10.5772/intechopen.75105.10.5772/intechopen.75105 ↗
54. In situ thermal, optical, and structural investigations on reversible thermochromism in bismuth molybdate10.1016/j.ceramint.2021.05.316 ↗
55. Molecular structure of molybdenum oxide in bismuth molybdates by Raman spectroscopy10.1021/j100179a045 ↗
56. Infrared and Raman spectra of MoO3 molybdenum trioxides and MoO3 · xH2O molybdenum trioxide hydrates10.1016/0584-8539(94)00247-9 ↗
57. Precise determination of the valence-band edge in X-ray photoemission spectra: application to measurement of semiconductor interface potentials10.1103/PhysRevLett.44.1620 ↗
58. Semiconductor core-level to valence-band maximum binding-energy differences: precise determination by x-ray photoelectron spectroscopy10.1103/PhysRevB.28.1965 ↗
59. Good practices for reporting the photocatalytic evaluation of a visible-light active semiconductor: Bi2O3, a case study10.1039/C9CY00038K ↗
60. Kinetics of photocatalyzed reactions: five lessons learned10.3389/fchem.2018.00378 ↗
61. Molybdenum, molybdenum oxides, and their electrochemistry10.1002/cssc.201100660 ↗
62. Enhanced photocatalytic drug degradation via nanoscale control of bismuth molybdate10.1021/acsanm.5c03249 ↗
63. Synthesis and characterization of a novel bismuth–molybdenum oxide and study of its ionic conducting behavior10.1016/j.solidstatesciences.2005.08.011 ↗
64. Synergy effects between bismuth molybdate catalyst phases (Bi/Mo from 0.57 to 2) for the selective oxidation of propylene to arcrolein10.1016/j.apcata.2004.12.010 ↗
65. Photophysical properties and photocatalytic activities of bismuth molybdates under visible light irradiation10.1021/jp0622482 ↗
66. Fe and W doped Bi2 MoO6 nanoflakes: a promising material for efficient solar water splitting, Sustainable
67. BiVO4, Bi2WO6 and Bi2MoO6 photocatalysis: a brief review10.1016/j.jmst.2020.04.023 ↗
68. Photocatalytic properties of Bi2MoO6 nanoparticles prepared by an amorphous complex precursor10.1016/j.cattod.2007.08.004 ↗
69. A rod-shaped Bi2MoO6/Bi14MoO24 homoelemental heterojunction for efficient degradation of tetracycline10.1016/j.jallcom.2025.182717 ↗
70. Photocatalytic degradation of Rhodamine-B and Crystal Violet in wastewater: a sustainable approach using bismuth molybdate10.1007/s42247-024-00749-3 ↗
71. Engineering the dimension and crystal structure of bismuth molybdate photocatalysts via a molten salt-assisted assembly approach10.1016/j.jallcom.2020.156231 ↗
72. The absolute energy positions of conduction and valence bands of selected semiconducting minerals10.2138/am-2000-0416 ↗
73. The “absolute” electrode potential—the end of the story10.1016/0013-4686(90)85069-Y ↗
74. Generation and detection of reactive oxygen species in photocatalysis10.1021/acs.chemrev.7b00161 ↗
75. Thermochemistry of proton-coupled electron transfer reagents and its implications10.1021/cr100085k ↗
76. Electronegativity equalization principle: new approaches and models for the study of chemical reactivity, in: Chemical Reactivity, Elsevier, 2023: pp. 227–242. Doi: 10.1016/B978-0-32-390259-5.00014-7.10.1016/B978-0-32-390259-5.00014-7 ↗
77. X-ray photoelectron spectroscopy: towards reliable binding energy referencing10.1016/j.pmatsci.2019.100591 ↗
78. Defining the nature of adventitious carbon and improving its merit as a charge correction reference for XPS10.1016/j.apsusc.2024.159319 ↗
79. ISO, ISO 19318:2021 Surface chemical analysis — X-ray photoelectron spectroscopy — Reporting of methods used for charge control and charge correction, (2021).
80. Standard Guide to Charge Control and Charge Referencing Techniques in X-Ray Photoelectron Spectroscopy, (n.d.). https://store.astm.org/e1523-09.html (accessed April 27, 2026).
81. Origin of the high work function and high conductivity of MoO310.1063/1.4903538 ↗
82. A synchrotron-based photoemission study of the MoO3/Co interface
83. Detailed work function and structural investigations of layered MoO3 onto SiO2 and MoS2 in air10.1016/j.apsusc.2024.160578 ↗
84. S-Scheme 2D/2D Bi2MoO6/BiOI van der Waals heterojunction for CO2 photoreduction10.1016/S1872-2067(21)64010-X ↗
85. Construction of a novel step-scheme CdS/Pt/Bi2MoO6 photocatalyst for efficient photocatalytic fuel denitrification10.1039/D1RA04417F ↗
86. High-efficiency Fe-Mediated Bi2MoO6 nitrogen-fixing photocatalyst: reduced surface work function and ameliorated surface reaction10.1016/j.apcatb.2019.117781 ↗