Modulation of the tribological performance of DLC coatings on titanium alloy via porous MAO interlayer towards enhanced mechanical interlocking and graphitized transfer film
Source abstract
Abstract
To address poor adhesion of diamond-like carbon (DLC) on titanium alloys, this work introduces a porous micro-arc oxidation (MAO) ceramic interlayer with low roughness and high hardness. An optimized MAO process produced an alumina/titania composite layer with uniform nanoporous structure on TA1 titanium alloy. Subsequently, an MAO/DLC composite coating was deposited using Ion Beam Deposition with Cr/Si-DLC gradient transitional layers. The porous MAO layer provides robust three-dimensional mechanical interlocking, increasing adhesion strength to 26.56 N—twice that of single DLC. Furthermore, the porous architecture induces a unique hill-like micro-texture on the DLC surface that optimizes contact stress and promotes highly graphitized transfer films on the counterpart surface, with the highest ID/IG ratio reaching 0.92 compared to 0.44 for single DLC. Benefiting from this structure-induced self-lubricating mechanism, the composite coating exhibits outstanding tribological performance: steady-state friction coefficient reduced by 17.8%–42.3%, lowest wear rate of 0.805×10-6 mm3/(N·m), and faster running-in adaptivity. This work overcomes the adhesion challenge of DLC on titanium alloys while achieving active regulation of tribological behavior.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Tribology and Lubrication Engineering
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. Surface modification of Ti6Al4V alloy via advanced coatings: mechanical, tribological, corrosion, wetting, and biocompatibility studies10.1016/j.jallcom.2024.174418 ↗
2. Review of micro-arc oxidation of titanium alloys: mechanism, properties and applications10.1016/j.jallcom.2023.169773 ↗
3. Hierarchical MAO–diamond coating for titanium alloys: enhancing tribological performance through experimental and atomistic insights10.1016/j.apsusc.2025.164393 ↗
4. Improving tribological properties of titanium alloys by combining laser surface texturing and diamond-like carbon film10.1016/j.triboint.2014.09.017 ↗
5. Surface damage mitigation of TC4 alloy via micro arc oxidation for oil and gas exploitation application: characterizations of microstructure and evaluations on surface performance10.1016/j.apsusc.2017.12.047 ↗
6. Tribocorrosion behavior of DLC-coated Ti-6Al-4V alloy deposited by PIID and PEMS + PIID techniques for biomedical applications10.1016/j.surfcoat.2017.07.004 ↗
7. Tribological and corrosive behavior under HCl corrosive environment of diamond-like carbon films with doped H, Cr and WC10.1016/j.surfcoat.2024.130685 ↗
8. Enhanced superlubricity on a-C films by lubrication with 3-hydroxypropionic acid10.1016/j.carbon.2022.07.062 ↗
9. Study on the wear resistance of TiN/TiO2 micro-arc oxidized composite coating on TC4 titanium alloy10.1007/s11665-025-10965-5 ↗
10. Characterization of additively manufactured titanium-based alloy with a micro-arc oxidation coating and overlying polyurethane layer10.3390/coatings15020137 ↗
11. Tribological properties of diamond-like carbon coatings prepared by anode layer source and magnetron sputtering10.1016/j.surfcoat.2011.01.043 ↗
12. Bactericidal abilities and in vitro properties of diamond-like carbon films deposited onto MAO-treated titanium10.1016/j.matlet.2019.02.069 ↗
13. Adhesion, biological corrosion resistance and biotribological properties of carbon films deposited on MAO coated Ti substrates10.1016/j.jmbbm.2019.103448 ↗
14. Micro-abrasive wear behavior by ball cratering on MAO coating of Ti–25Ta alloy10.1016/j.jmrt.2023.08.023 ↗
15. Surface texturing effects on the tribological performance of DLC coated Ti-6Al-4V under lubricated conditions
16. Tribological behavior and wear mechanism of TiO2/MoS2 nanocomposite coatings fabricated on TC6 alloys by micro-arc oxidation and duplex surface technologies10.1016/j.surfcoat.2025.132227 ↗
17. Exploring the friction and wear characteristics of MAO and MoSe2 tailored micro-pocket interface across wide temperature range10.1016/j.surfcoat.2024.131477 ↗
18. Syntheses and bandgap alterations of MoS2 induced by stresses in graphene-platinum substrates10.1016/j.carbon.2018.01.085 ↗
19. Recent advances in Carbon Dots/2-D hybrid materials10.1016/j.carbon.2022.04.029 ↗
20. Influence of Cr-Al-Si-N and DLC-Si thin coatings on wear resistance of titanium alloy samples with different surface conditions10.3390/coatings13091581 ↗
21. Tribocorrosion behavior of Ti6Al4V alloy after thermo-chemical treatment and DLC deposition for biomedical applications10.1016/j.triboint.2020.106560 ↗
22. Wear resistant multilayer nanocomposite WC1−x/C coating on Ti–6Al–4V titanium alloy10.1016/j.triboint.2014.05.030 ↗
23. Plasma electrolysis for surface engineering10.1016/S0257-8972(99)00441-7 ↗
24. Effect of laser rescanning on microstructure and mechanical properties of direct energy deposited AISI 316L stainless steel10.1016/j.surfcoat.2020.126540 ↗
25. Commentary on using H/E and H/E as proxies for fracture toughness of hard coatings10.1016/j.tsf.2019.04.040 ↗
26. Wear and adhesion resistance of duplex coatings deposited on Ti6Al4V alloy using MAO and CFUBMS10.1016/j.surfcoat.2012.10.006 ↗
27. Tribological properties of duplex MAO/DLC coatings on magnesium alloy using combined microarc oxidation and filtered cathodic arc deposition10.1016/j.msea.2006.12.051 ↗
28. Nano-texture for a wear-resistant and near-frictionless diamond-like carbon10.1016/j.carbon.2014.03.003 ↗
29. Friction mechanism of DLC/MAO wear-resistant coatings with porous surface texture constructed in-situ by micro-arc oxidation10.1016/j.surfcoat.2023.130010 ↗
30. Effect of different hardness units on fatigue wear resistence of low hardenability steel10.1016/j.optlastec.2020.106325 ↗
31. Effects of hardness and grain size on wear resistance of polycrystalline cubic boron nitride10.1016/j.ijrmhm.2021.105766 ↗
32. The influence mechanism of the hardness homogeneity of the grind-hardening layer on its wear resistance10.3390/coatings15101196 ↗
33. Microstructural transformation impact on mechanical and tribological performance of different temperature heat-treated carbon/carbon composites10.1016/j.ceramint.2024.06.423 ↗
34. Properties of polydimethylsiloxane hydrophobic modified duplex microarc oxidation/diamond-like carbon coatings on AZ31B Mg alloy10.1016/j.jma.2020.04.009 ↗
35. Shear-Induced structural changes and origin of ultralow friction of hydrogenated diamond-like carbon (DLC) in dry environment10.1021/acsami.7b03360 ↗
36. Ni20/PTFE composite coating material and the synergistic friction reduction and wear resistance mechanism under multiple working conditions10.3390/coatings15070830 ↗