journal article·2026-08Open access

Wear mechanism of activated zinc phosphate conversion coatings under dry and lubricated sliding

Mohammad Alinezhadfar, Vincent Niggel, Michał Góra, Nicolas O. Wyler, Patrik Schmutz, Ueli Angst, Rowena Crockett

Abstract

• Uniformly adsorbed zinc phosphate activators affected conversion coating formation. • Activated coatings showed lower roughness, open pores, and dry-sliding friction. • Activation eliminated porous interlayer and reduced zinc-iron phosphate formation. • Dry sliding led to coating indenting into substrate and substrate grain refinement. • MCT lubrication stabilized low friction and reduced damage to coating and substrate. Zinc phosphate conversion coatings are widely used to improve the functional performance of steel surfaces. A pretreatment step known as activation is commonly applied to enhance nucleation density and deposition efficiency. However, conventional activation methods rely on complex chemistries. In this work, a cost-effective activation strategy based on pure zinc phosphate particles is introduced to control coating formation and improve its performance. The adsorption of zinc phosphate particles on the steel surface prior to phosphating was directly confirmed by time-of-flight secondary ion mass spectrometry (ToF-SIMS) and scanning electron microscopy (SEM). These pre-adsorbed particles layer altered the coating formation mechanism. SEM and X-ray diffraction (XRD) analyses revealed a pronounced refinement of crystal size and a reduced contribution of the zinc-iron phosphate phase in activated coatings. Cross-sectional focused ion beam (FIB)-SEM and scanning transmission electron microscopy (STEM) analyses showed that, with activation step, zinc phosphate coating was directly attached to the substrate, while without activation, coating formed on a porous interface layer. Electrochemical impedance spectroscopy (EIS) combined with surface profilometry demonstrated a significant reduction in open porosity and surface roughness. Under dry sliding conditions, activated coatings consistently exhibited lower friction than non-activated coatings. Wear track cross-sections revealed wear initiation through crystal fragmentation and third-body compaction, followed by localized substrate indentation and grain refinement at extended sliding times. Under lubrication with medium-chain triglyceride oil, friction remained stable at low values over more than 5 h of continuous sliding. Cross-sectional analyses confirmed that lubrication preserved the zinc phosphate layer and effectively suppressed substrate damage.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Tribology and Wear Analysis · Polymer Science and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Surface pretretament by phosphate conversion coatings-a review
2. K. Ogle, M. Wolpers, Phosphate conversion coatings, in: Corrosion: Fundamentals, Testing, and Protection, ASM International, 2003, pp. 712–719.10.31399/asm.hb.v13a.a0003678 ↗
3. Colloidal titanium phosphate, the chemical activator in surface conditioning before zinc phosphating10.1016/0166-6622(89)80083-6 ↗
4. The mechanism of chemical activation with titanium phosphate colloids in the formation of zinc phosphate conversion coatings10.1016/0166-6622(90)80118-N ↗
5. Investigations of the kinetics of surface treatments by advanced methods
6. Activation of galvanized steel surfaces before zinc phosphating—XPS and GDOES investigations10.1016/S0169-4332(01)00296-3 ↗
7. Characteristics of zinc phosphate coating activated by different concentrations of nickel acetate solution10.1007/s11661-016-3876-x ↗
8. Activation of zinc phosphate coating by silver nitrate pretreatment10.1080/02670844.2016.1277842 ↗
9. Corrosion performance and morphological analysis of activated zinc phosphate coating formed on steel surface10.1108/ACMM-03-2021-2462 ↗
10. The role of phosphate-conversion coatings in the makeup and sealing ability of casing connections10.2118/184690-PA ↗
11. Surface and wear analysis of zinc phosphate coated engine oil ring and cylinder liner tested with commercial lubricant10.1155/2014/150968 ↗
12. Applications of thin coatings in automotive industry
13. Study on tribological behavior of zinc phosphate impregnated graphite under oil lubrication condition10.1115/1.4051586 ↗
14. Friction behavior of lubricated zinc phosphate coatings10.1016/j.wear.2008.10.002 ↗
15. Mechanical characterization and single asperity scratch behaviour of dry zinc and manganese phosphate coatings10.1016/j.triboint.2017.04.034 ↗
16. Dry sliding wear behavior of hard-chrome and zinc-phosphate conversion coatings on steel substrates10.1177/13506501241227478 ↗
17. Exploration and tuning of Al2O3/Mo composite for enhancement of anti-corrosion and tribological characteristics in zinc phosphate conversion coatings10.1016/j.apsusc.2022.153370 ↗
18. Effect of carbon on the corrosion and wear performance of Zn-phosphate layers10.1016/j.electacta.2015.12.083 ↗
19. Mechanism of zinc phosphate conversion coating formation on iron-based substrates10.1016/j.corsci.2025.112796 ↗
20. Impedance study on the corrosion of PVD and CVD titanium nitride coatings, in
21. Electrochemical impedance spectroscopy and linear polarization applied to evaluation of porosity of phosphate conversion coatings on electrogalvanized steels10.1016/j.apsusc.2006.06.030 ↗
22. Porosity evaluation of protective coatings onto steel, through electrochemical techniques10.1016/S0257-8972(99)00659-3 ↗
23. Characterization of surface structure by cluster coincidental ion mass spectrometry10.1016/j.apsusc.2004.03.079 ↗
24. Chain-length-identification strategy in zinc polyphosphate glasses by means of XPS and ToF-SIMS10.1007/s00216-012-5836-7 ↗
25. Mechanochemical processing of sustainable TiO2 electrocatalysts: Divergent doping behaviors of Fe and Cu toward oxygen evolution
26. Principal investigation on the surface chemistry of phosphated zinc coatings treated by hot active plasma10.1016/j.apsusc.2024.160308 ↗
27. Zinc phosphate conversion coatings on magnesium alloys: a review10.1007/s12540-013-2023-0 ↗
28. Effect of temperature on the morphology and corrosion resistance of modified boron nitride nanosheets incorporated into steel phosphate coating10.3390/met13071186 ↗
29. Tribological interaction of manganese phosphate coatings with grease and solid lubricant particles10.1007/s11249-019-1258-4 ↗
30. An environment-friendly phosphate chemical conversion coating on novel Mg-9Li-7Al-1Sn and Mg-9Li-5Al-3Sn-1Zn alloys with remarkable corrosion protection10.1016/j.apsusc.2018.02.254 ↗
31. Microstructural characterization and surface properties of zinc phosphated medium carbon low alloy steel10.1016/j.surfcoat.2012.02.052 ↗
32. Influence of surface roughness and phosphate coating on galling resistance of medium-grade carbon steel
33. Characteristics of manganese phosphate coatings for wear-resistance applications10.1016/0043-1648(79)90159-5 ↗
34. Surface pretreatment by phosphate conversion coatings—a review
35. Functional atomic force microscopy investigation of osteopontin affinity for silicon stabilized tricalcium phosphate bioceramic surfaces10.1016/j.biomaterials.2005.05.093 ↗
36. Zinc phosphate as versatile material for potential biomedical applications Part II10.1007/s10856-006-6333-3 ↗
37. Effect of different chemical conversion coatings on the tribological performance of cylindrical thrust roller bearings under conditions of dry friction and solid lubrication
38. Influence of long-chain/medium-chain triglycerides and whey protein/tween 80 ratio on the stability of phosphatidylserine emulsions10.1021/acsomega.9b03702 ↗
39. Effect of mechanical factors on tribological properties of palm oil methyl ester blended lubricant10.1016/S0043-1648(00)00319-7 ↗
40. Experimental simulation of tribochemical reactions between borates esters and steel surface10.1007/s11249-010-9685-2 ↗