journal article·2026-06Open access

Voltage-controlled composition tuning of anodic oxide layers on alloy surface using anodization

Jun Heo, Jichan Kim, Sung Oh Cho

Abstract

• Selective anodic layer composition tailoring achieved via voltage tuning. • Voltage determines the dominant driver of anodic oxide formation. • Fe/Cr-rich spinels formed at high voltages in composition ratio-driven regime. • Al 2 O 3 -rich layers emerge at low voltages in oxidation tendency-driven regime. Anodization is a widely employed surface engineering strategy for improving comprehensive performance enhancement, particularly in single-component valve metals. In this study, we extend the anodization approach to a multicomponent system to enable compositional control of anodic layers. Using FeCrAl alloy as a prototype substrate, we demonstrate that the applied voltage can be used to modulate the electrochemical oxidation behavior of individual alloying elements. At high potentials (≥60 V), field-assisted ion mobility and composition ratio dominate, resulting in the preferential formation of Fe 3 O 4 and FeCr 2 O 4 phases, defined as the “composition ratio-dominant” regime. In contrast, lowering the voltage (≤30 V) leads to the introduction of transition and α-Al 2 O 3 phases, governed by the superior intrinsic oxidation tendency of Al, termed the “oxidation tendency-dominant” regime. While precise control of oxide architecture in complex systems also depends on factors such as electrolyte chemistry, alloy composition, and temperature, this work demonstrates that voltage alone can drive the formation of tailored anodic layers. This finding offers a broad applicability for designing compositionally selective oxides with strong potential for widespread impact through fields such as corrosion protection, catalysis, sensing, energy devices, and beyond.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Anodic Oxide Films and Nanostructures · High-Temperature Coating Behaviors · Electrocatalysts for Energy Conversion

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (52)

Show source-provided references
1. Advances in corrosion-resistant thermal spray coatings for renewable energy power plants. Part I: effect of composition and microstructure10.1007/s11666-019-00938-1 ↗
2. An experimental study of the wear performance of NiCrBSi thermal spray coatings10.1016/S0043-1648(03)00162-5 ↗
3. Wear-resistant ceramic coatings deposited by liquid thermal spraying10.1016/j.ceramint.2022.07.267 ↗
4. Study of vanadium-based chemical conversion coating on the corrosion resistance of magnesium alloy10.1016/j.matchemphys.2006.08.007 ↗
5. Phosphate chemical conversion coatings on metallic substrates for biomedical application: a review10.1016/j.msec.2014.11.038 ↗
6. Study on corrosion resistance of electroplating zinc–nickel alloy coatings10.1002/sia.3017 ↗
7. Electrodeposition of Ni–SiC nano-composite coatings and evaluation of wear and corrosion resistance and electroplating characteristics10.1016/j.colsurfa.2007.07.027 ↗
8. Identifying adhesion characteristics of metal-polymer interfaces: recent advances in the case of electroplated acrylonitrile butadiene styrene
9. Corrosion behavior of Cu during graphene growth by CVD10.1016/j.corsci.2014.08.026 ↗
10. Resistance of PVD coatings to erosive and wear processes: a review10.3390/coatings10100921 ↗
11. MOF-based protective coatings for metal corrosion protection: a critical review of design/synthesis, performance, and mechanism10.1016/j.mseb.2024.117932 ↗
12. Wear-and corrosion-resistant coatings for extreme environments: advances, challenges, and future perspectives10.3390/coatings15080878 ↗
13. Porous anodic aluminum oxide: anodization and templated synthesis of functional nanostructures10.1021/cr500002z ↗
14. Anodizing of iron-based alloys: fundamentals, recent progress, and applications10.1088/1361-6633/ad959b ↗
15. A unified thermodynamic theory for the formation of anodized metal oxide structures10.1016/j.electacta.2011.12.054 ↗
16. Corrosion resistance of austenitic stainless steel using cathodic plasma electrolytic oxidation10.1016/j.surfcoat.2023.129448 ↗
17. Improvement of corrosion resistance of stainless steel welded joint using a nanostructured oxide layer10.3390/nano11040838 ↗
18. Self-organized honeycomb-like nanoporous oxide layer for corrosion protection of type 304 stainless steel in an artificial seawater medium10.1016/j.molliq.2019.111823 ↗
19. Self-adaptive MgAl2O4 spinel layer for enhanced corrosion resistance of alumina-forming alloy in molten chloride salts10.1016/j.corsci.2025.113262 ↗
20. Enhanced wear resistance and surface properties of oxide film coating on biocompatible Ti45Nb alloy by anodization method10.1016/j.surfcoat.2023.129797 ↗
21. Improving the wear resistance of aluminum by a nickel-filled anodized porous alumina layer10.1016/j.wear.2023.204858 ↗
22. The effect of anodization temperature on optical properties of nanoporous anodic alumina (NAA) films10.1016/j.jelechem.2016.01.009 ↗
23. Influence of anodization mode and temperature on the optical properties of photonic crystals based on porous anodic alumina10.1149/1945-7111/ad1370 ↗
24. Effects of graphene oxide-filled sol-gel sealing on the corrosion resistance and paint adhesion of anodized aluminum10.1016/j.apsusc.2019.02.005 ↗
25. Improvement of adhesion performance between aluminum alloy sheet and epoxy based on anodizing technique10.1016/j.ijadhadh.2016.05.007 ↗
26. Recent progress in Li-ion batteries with TiO2 nanotube anodes grown by electrochemical anodization10.1007/s12598-020-01499-x ↗
27. TiO2 nanotube array film prepared by anodization as anode material for lithium ion batteries10.1007/s10008-009-0910-6 ↗
28. Recent progress of self‐supported metal oxide nano‐porous arrays in energy storage applications10.1002/smll.202302786 ↗
29. Use of modified anodization procedures to prepare advanced TiO2 nanostructured catalytic electrodes and thin film materials10.1016/j.cattod.2014.11.003 ↗
30. A brief history of anodizing aluminum10.1007/978-3-319-72177-4_2 ↗
31. Controlled fabrication of nanoporous oxide layers on zircaloy by anodization10.1186/s11671-015-1086-x ↗
32. Corrosion resistance of plasma-anodized AZ91D magnesium alloy by electrochemical methods10.1016/j.electacta.2007.04.030 ↗
33. Performance of an FeCrAl alloy in a high-temperature CO2 environment10.1016/j.corsci.2018.05.007 ↗
34. Microstructure and high temperature mechanical properties of as-cast FeCrAl alloys10.1016/j.msea.2018.04.039 ↗
35. A study of the oxidation of FeCrAl alloy in pressurized water and high-temperature steam environment10.1016/j.corsci.2015.02.027 ↗
36. Recent advances in the application of magnetite (Fe3O4) in lithium-ion batteries: Synthesis, electrochemical performance, and characterization techniques10.1021/acs.chemmater.4c02013 ↗
37. Flower-like magnetite nanoparticles with unfunctionalized surface as an efficient catalyst in photo-Fenton degradation of chemical dyes10.1016/j.apsusc.2023.158127 ↗
38. N–doping of alumina thin film support to improve the thermal stability of Catalysts: Preparation and investigation10.1016/j.apsusc.2021.150631 ↗
39. High-performance and safe lithium-ion battery with precise ultrathin Al2O3-coated polyethylene separator10.1016/j.apsusc.2024.159918 ↗
40. Influence of water content on the formation of TiO2 nanotubes and photoelectrochemical hydrogen generation10.1016/j.jallcom.2017.03.007 ↗
41. Effect of processing parameters on pore structure and thickness of anodic aluminum oxide (AAO) tubular membranes10.1016/j.memsci.2008.03.044 ↗
42. Effects of the voltage and time of anodization on modulation of the pore dimensions of AAO films for nanomaterials synthesis10.1016/j.spmi.2015.10.011 ↗
43. Pore diameter control of anodic aluminum oxide with ordered array of nanopores10.1016/j.electacta.2007.09.039 ↗
44. Thermal analysis of phase transformation kinetics in α-Al2O3 seeded boehmite and γ-Al2O310.1016/S0040-6031(98)00343-8 ↗
45. Thermal evolution of transitional aluminas followed by NMR and IR spectroscopies10.1021/jp983316q ↗
46. Influence of fluorides on phase transition of α-Al2O3 formation10.1016/j.ceramint.2006.02.002 ↗
47. Modification of alumina barrier-layer through re-anodization in an oxalic acid solution with fluoride additives10.1016/j.apsusc.2005.04.007 ↗
48. Influences of precursor and additive on the morphology of nanocrystalline α-alumina10.1016/j.jpcs.2007.10.024 ↗
49. Effects of size and specific Surface Area of Boron Nitride Particles on the Crystallization of Bacterial Poly (3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)
50. Surface energy and structure effects on surface crystallization10.1016/0022-3093(94)00643-1 ↗
51. Voltage effect on electrochemical anodization of aluminum at ambient temperature
52. The role of electric field in pore formation during aluminum anodization10.1016/j.electacta.2011.02.002 ↗