Three-phase heterogenous microstructure and hardness enhancement in a TiZrHfMoW-O high-entropy coating prepared by reactive glow discharge sputtering
Source abstract
Abstract
A TiZrHfMoW–O high-entropy alloy (HEA) metal–metal oxide coating was fabricated via double-cathode glow discharge sputtering under an argon-to-oxygen (Ar:O 2 ) flow ratio of 30:1. Detailed microstructural analysis revealed a coating ∼23.6 μm in thickness, possessing a complex three-phase architecture consisting of a body-centered cubic (bcc) HEA metallic phase, a spinel-type high-entropy oxide (HEO) phase, and a face-centered cubic (fcc) oxide phase. The coating exhibited a heterogeneous microstructure across its cross-section, transitioning from equiaxed grains, ∼20 nm in diameter, in the inner region to ultra-fine grains, ∼2 nm in diameter, in the outer region. High-resolution TEM confirmed the co-existence of all three phases within individual microstructural domains, forming ultra-fine grain clusters together with intricate phase boundaries that enhance mechanical properties through interfacial strengthening. Additionally, the coating exhibited a compressive residual stress, further contributing to its hardness. The maximum hardness reached ∼22.6 ± 0.2 GPa—approximately 2.4 times higher than its fully metallic, oxygen-free TiZrHfMoW counterpart (∼9.6 ± 0.8 GPa). These findings demonstrate that partial oxidation during sputtering can significantly strengthen HEA coatings through multiple synergistic mechanisms.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: High Entropy Alloys Studies · Metal and Thin Film Mechanics · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (79)
Show source-provided references
1. Huang · 1996
2. Phase composition and solid solution strengthening effect in TiZrNbMoV high-entropy alloys10.1016/j.matdes.2015.06.072 ↗
3. Unusual dislocation behavior in high-entropy alloys10.1016/j.scriptamat.2020.02.021 ↗
4. Oxidation behavior of a refractory NbCrMo0.5Ta0.5TiZr alloy10.1007/s10853-012-6582-0 ↗
5. Microstructure and elevated temperature properties of a refractory TaNbHfZrTi alloy10.1007/s10853-012-6260-2 ↗
6. Mechanical properties of Nb25Mo25Ta25W25 and V20Nb20Mo20Ta20W20 refractory high entropy alloys10.1016/j.intermet.2011.01.004 ↗
7. Refractory high-entropy alloys10.1016/j.intermet.2010.05.014 ↗
8. High entropy alloy coatings and technology10.3390/coatings11040372 ↗
9. Atomic size effect on the formability of metallic glasses
10. Solid‐solution phase formation rules for multi‐component alloys10.1002/adem.200700240 ↗
11. Entropy-driven phase stability and slow diffusion kinetics in an Al0.5CoCrCuFeNi high entropy alloy10.1016/j.intermet.2012.07.001 ↗
12. Structure and properties of high-entropy nitride coatings10.3390/met12050847 ↗
13. Multi-component and high-entropy nitride coatings—a promising field in need of a novel approach10.1063/1.5144154 ↗
14. Processing and properties of high-entropy ultra-high temperature carbides10.1038/s41598-018-26827-1 ↗
15. Controlling the electrical properties of reactively sputtered high entropy alloy CrFeNiCoCu films10.1007/s11664-021-09343-3 ↗
16. Recent progress in high entropy alloys
17. Understanding the role of entropy in high entropy oxides10.1021/jacs.2c11608 ↗
18. Entropy-stabilized oxides10.1038/ncomms9485 ↗
19. Structure and properties of reactively-sputtered AlxCoCrCuFeNi oxide films
20. Thermodynamics of high entropy oxides10.1016/j.actamat.2020.10.043 ↗
21. Crystallography of a new Mn(V,Ti,Al)2O4 compositionally complex spinel oxide in a BCC compositionally complex alloy10.1016/j.scriptamat.2023.115683 ↗
22. Magnetron sputtering high-entropy alloy coatings: a mini-review10.3390/met12020319 ↗
23. Performance and local structure evolution of NbMoTaWV entropy-stabilized oxide thin films with variable oxygen content10.1016/j.surfcoat.2020.126326 ↗
24. High-entropy oxide thin films based on Al–Cr–Nb–Ta–Ti10.1016/j.vacuum.2019.108850 ↗
25. Magnetron co-sputtering synthesis and nanoindentation studies of nanocrystalline (TiZrHf)x(NbTa)1−x high-entropy alloy thin films10.1007/s12274-021-3805-1 ↗
26. Tuning microstructure and mechanical and wear resistance of ZrNbTiMo refractory high-entropy alloy films via sputtering power
27. Synthesis and characterization of refractory TiZrNbWMo high-entropy alloy coating by laser cladding10.1016/j.surfcoat.2017.01.012 ↗
28. Titanium bipolar plates augmented by nanocrystalline TiZrHfMoW coatings for application in proton exchange membrane fuel cells10.1016/j.apsusc.2022.153200 ↗
29. The impact of surface scratches on the corrosion behavior of nanocrystalline high entropy alloy coatings: electrochemical experiments and first-principles study
30. Residual stresses in Cu/Ni multilayer thin films measured using the sin2ψ method10.1007/s11340-018-00447-2 ↗
31. Measurement of hardness and elastic modulus by instrumented indentation: advances in understanding and refinements to methodology10.1557/jmr.2004.19.1.3 ↗
32. Estimating the structure factors in X-ray diffraction10.1107/S2053273318007593 ↗
33. Determination of crystallinity of thermosetting urea-formaldehyde resins using deconvolution method10.1007/s13233-020-8076-2 ↗
34. A structure zone diagram obtained by simultaneous deposition on a novel step heater: a case study for Cu2O thin films
35. Determination of crystallite size with the X‐Ray spectrometer10.1063/1.1699612 ↗
36. P. Touseef Ahmad, S. Shaibal Kanti, Challenges in Rietveld Refinement and Structure Visualization in Ceramics, in: M. Mohsen (Ed.), Advanced Ceramic Materials, IntechOpen, p. Ch. 12 (2021) https://doi.org/10.5772/intechopen.96065.10.5772/intechopen.96065 ↗
37. Evaluation of the volume fraction of nanocrystals devitrified in Al-based amorphous alloys
38. Effect of Ni content on the microstructure and mechanical behaviour of CrAlNiN coatings deposited by closed field unbalanced magnetron sputtering10.1016/j.surfcoat.2018.10.052 ↗
39. Enhanced quantification for 3D SEM–EDS: using the full set of available X-ray lines10.1016/j.ultramic.2014.10.010 ↗
40. Acquisition and evaluation procedure to improve the accuracy of SAED10.1002/jemt.24229 ↗
41. D.B. Williams, C.B. Carter, The transmission electron microscope, Transmission electron microscopy: a textbook for materials science, Springer, pp. 3-17 (1996) https://doi.org/10.1007/978-1-4757-2519-3.10.1007/978-1-4757-2519-3_1 ↗
42. Microstructure and tribological properties of TiTaHfNbZr high entropy alloy coatings deposited on Ti6Al4V substrates10.1016/j.intermet.2018.11.015 ↗
43. Structural and mechanical properties of multi-element (TiVCrZrHf) N coatings by reactive magnetron sputtering10.1016/j.apsusc.2011.09.006 ↗
44. Investigation of microstructure, mechanical properties, and biocorrosion behavior of Ti1.5ZrTa0.5Nb0.5W0.5 refractory high-entropy alloy film doped with Ag nanoparticles
45. Characteristics of TiVCrAlZr multi-element nitride films prepared by reactive sputtering10.1016/j.nimb.2010.05.039 ↗
46. High entropy oxide thin films of (HfNbTaTiZr)Ox by pulsed laser deposition10.1016/j.surfcoat.2025.132129 ↗
47. Target poisoning during reactive sputtering of silicon with oxygen and nitrogen
48. Nanostructured nitride films of multi-element high-entropy alloys by reactive DC sputtering
49. Nanostructured AlCoCrCu0.5FeNi high entropy oxide (HEO) thin films fabricated using reactive magnetron sputtering10.1016/j.apsusc.2021.149491 ↗
50. Lithium storage characteristic of nanoporous high-entropy alloy@high-entropy oxide with spin-dependent synergism of cations10.1016/j.cej.2023.146881 ↗
51. Spinels: Controlled preparation, oxygen reduction/evolution reaction application, and beyond10.1021/acs.chemrev.7b00051 ↗
52. Synthesis, elastic properties, and high-temperature stability of multicomponent spinel oxide10.1557/s43579-022-00210-8 ↗
53. Synthesis and characterization of zirconium substituted cobalt ferrite nanopowders10.1166/jnn.2016.11775 ↗
54. Crystal structures of spinel-type Na2MoO4 and Na2WO4 revisited using neutron powder diffraction
55. Thermodynamics of A3O4-B3O4 spinel solid solutions10.1016/0022-1902(69)80054-0 ↗
56. Understanding the self-reconfiguration properties of a novel spinel-type high-entropy catalyst10.1002/cctc.202400971 ↗
57. The effect on electrochemical properties of Ti4+ and V5+ doping in LiNi0.8Co0.1Mn0.1O210.1016/j.jallcom.2023.170451 ↗
58. Ionization energy calculations of MCl4 (M·Ti, Zr and Hf)-type molecules by the MS Xα method
59. The thermodynamics of formation, molar heat capacity, and thermodynamic functions ofZrTiO4(cr)10.1006/jcht.2000.0755 ↗
60. Complexation of Zr and Hf in fluoride-rich hydrothermal aqueous fluids and its significance for high field strength element fractionation10.1016/j.gca.2023.12.013 ↗
61. Oxidation of amorphous HfNbTaTiZr high entropy alloy thin films prepared by DC magnetron sputtering10.1016/j.jallcom.2020.157978 ↗
62. Interaction of cations on octahedral and tetrahedral sites in simple spinels10.1007/BF00309461 ↗
63. Residual stresses in thin film systems: Effects of lattice mismatch, thermal mismatch and interface dislocations
64. Influence of substrate temperature and deposition rate on structure of thick sputtered Cu coatings
65. Grain size and growth of Ni-Rich Ni-Al alloy films10.1016/0001-6160(83)90029-9 ↗
66. Influence of apparatus geometry and deposition conditions on the structure and topography of thick sputtered coatings
67. The microstructure of sputter‐deposited coatings10.1116/1.573628 ↗
68. Perspectives on oblique angle deposition of thin films: from fundamentals to devices10.1016/j.pmatsci.2015.06.003 ↗
69. Tunable hydrophilicity in a surface nano-textured stainless steel thin film deposited by DC magnetron sputtering10.1016/j.apsusc.2021.149705 ↗
70. Entropic phase transformation in nanocrystalline high entropy oxides10.1080/21663831.2018.1554605 ↗
71. Diffusion enhancement due to low‐energy ion bombardment during sputter etching and deposition10.1063/1.328265 ↗
72. Vegard's law10.1103/PhysRevA.43.3161 ↗
73. Hysteresis effects in the sputtering process using two reactive gases10.1016/0040-6090(94)06501-2 ↗
74. A review on fundamental of high entropy alloys with promising high–temperature properties10.1016/j.jallcom.2018.05.067 ↗
75. Experimental and mechanistic investigation of the residual stress in SiCP/Al composites at the multi scale10.1016/j.matdes.2025.113888 ↗
76. Hall-Petch strengthening in nanocrystalline metals
77. Below the hall–petch limit in nanocrystalline ceramics10.1021/acsnano.7b07380 ↗
78. (Zr,Ti,O) alloy films with enhanced hardness and resistance to cracking prepared by magnetron sputtering10.1016/j.surfcoat.2017.05.006 ↗
79. Reinforcement of nanoglasses by interface strengthening10.1016/j.scriptamat.2017.08.004 ↗