Enhanced tribological behavior of anodic films containing SiC and PTFE nanoparticles on Ti6Al4V alloy
Source abstract
Abstract
Abstract Anodic films containing SiC and polytetrafluoroethylene (PTFE) nanoparticles were successfully fabricated on Ti6Al4V alloy by using anodic oxidation method in an environmental friendly electrolyte. The morphology, structure and composition of the films were studied with the scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). The results showed that the film contained a layered structure and have a surface full of petaloid bulges, which was totally different from the common anodic oxide film of the porous kind. The tribological properties of the films were investigated with dry friction tests in terms of the friction coefficient, wear rate and the morphology of worn surfaces. The results indicated that the SiC/PTFE composite film exhibited much better anti-wear and anti-friction performances than that of the SiC composite film, the PTFE composite film and the ordinary film without nanoparticles. The SiC/PTFE composite film has friction coefficient of 0.1 and wear rate of 20.133 mg/m, which was decreased respectively by 80% and 44.5% compared with that of the ordinary film. The lubricating mechanisms of the composite film containing SiC and PTFE nanoparticles were discussed. PTFE nanoparticles could lead to the formation of lubricating layer while SiC nanoparticles inside the lubricating layer turned sliding friction to rolling friction.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Orthopaedic implants and arthroplasty · Anodic Oxide Films and Nanostructures · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. Structure and physicochemistry of anodic oxide films on titanium and TA6V alloy10.1002/(SICI)1096-9918(199907)27:7<629::AID-SIA551>3.0.CO;2-0 ↗
2. Kinetic model of anodic oxidation of titanium in sulphuric acid
3. Tribological properties of titanium alloys10.1016/0043-1648(91)90249-T ↗
4. Anodic oxidation of titanium and its alloys10.1007/BF00561225 ↗
5. Anodic growth of titanium oxide: electrochemical behaviour and morphological evolution10.1016/j.electacta.2012.04.114 ↗
6. Investigation of wear behavior of titanium oxide films, produced by anodic oxidation, on commercially pure titanium in vacuum conditions10.1016/j.surfcoat.2010.08.079 ↗
7. Electrophoretic deposition of PTFE particles on porous anodic aluminum oxide film and its tribological properties10.1016/j.apsusc.2013.11.114 ↗
8. Synthesis of anodizing composite films containing superfine Al2O3 and PTFE particles on Al alloys10.1016/j.apsusc.2010.04.040 ↗
9. Anodic films containing polyaniline and nanoparticles for corrosion protection of AA2024T3 aluminium alloy10.1016/j.surfcoat.2008.11.023 ↗
10. Improvement of the tribological behavior of PTFE-anodic film composites prepared on 1050 aluminum substrate10.1016/j.apsusc.2012.05.022 ↗
11. Wear behaviour of aluminium alloy and its composites reinforced by SiC particles using statistical analysis10.1016/S0261-3069(02)00143-7 ↗
12. Abrasive wear behavior of Si3N4/TiO2 nanocomposite coatings fabricated by plasma electrolytic oxidation10.1016/j.surfcoat.2010.03.052 ↗
13. AC plasma electrolytic oxidation of magnesium with zirconia nanoparticles10.1016/j.apsusc.2008.04.100 ↗
14. Formation of Al2O3–TiO2 composite oxide films on aluminum foil by cathodic electrodeposition and anodizing10.1016/j.ceramint.2011.11.019 ↗
15. The tribology properties of alumina/silica composite nanoparticles as lubricant additives10.1016/j.apsusc.2011.01.084 ↗
16. Self-lubricating Al2O3/PTFE composite coating formation on surface of aluminium alloy10.1016/j.surfcoat.2010.03.049 ↗
17. Preparation and self-lubrication treatment of ordered porous anodic alumina film10.1016/S0254-0584(03)00265-7 ↗
18. Anodic oxidation of titanium and TA6V alloy in chromic media. An electrochemical approach10.1016/S0013-4686(99)00283-2 ↗
19. Morphology and performances of the anodic oxide films on Ti6Al4V alloy formed in alkaline-silicate electrolyte10.1016/j.apsusc.2013.08.043 ↗
20. Dispersion of nano-silicon carbide (SiC) powder in aqueous suspensions10.1007/s11051-006-9121-6 ↗
21. Surface characterisation and modification of submicron and nanosized silicon carbide powders10.1016/j.jeurceramsoc.2007.02.199 ↗
22. Porous anodic film formation on Al–Ti alloys in sulphuric acid10.1016/j.corsci.2011.12.035 ↗
23. Influence of anodization parameters on the volume expansion of anodic aluminum oxide formed in mixed solution of phosphoric and oxalic acids10.1016/j.apsusc.2013.10.091 ↗
24. Surface characteristics of anodic oxide films fabricated in acid and neutral electrolytes on Ti–10V–2Fe–3Al alloy10.1002/sia.5113 ↗
25. Tribological properties of nanoporous anodic aluminum oxide film10.1016/j.surfcoat.2010.07.056 ↗
26. Effect of SiC particles on microarc oxidation process of magnesium matrix composites10.1016/j.apsusc.2013.07.041 ↗
27. Formation of anodic TiO2 nanotube or nanosponge morphology determined by the electrolyte hydrodynamic conditions10.1016/j.elecom.2012.09.041 ↗
28. Tribological rutile-TiO2 coating on aluminium alloy10.1016/j.apsusc.2004.03.241 ↗
29. The properties of poly (tetrafluoroethylene) (PTFE) in compression10.1016/j.polymer.2004.08.064 ↗
30. Fabrication of self-lubricating coating on aluminum and its frictional behavior10.1016/j.apsusc.2006.09.058 ↗
31. Microstructure and microhardness of SiC nanoparticles reinforced magnesium composites fabricated by ultrasonic method10.1016/S0921-5093(04)00936-0 ↗