Effects of surface treatments and bonding types on the interfacial behavior of fiber metal laminate based on magnesium alloy
Source abstract
Abstract
Abstract Fiber metal laminates based on magnesium alloys (MgFML) with different surface treatments and different bonding types were tested and analyzed. By using dynamic contact angle measurement and scanning electron microscopy (SEM), it was found that phosphating treatment can significantly improve the surface energy and wettability of magnesium alloy, and the surface energy of phosphated magnesium alloy was approximately 50% higher than that of abraded-only magnesium alloy. The single cantilever beam (SCB) test showed that the interfacial fracture energies of directly bonded MgFMLs based on abraded-only magnesium and abraded + phosphated magnesium were 650 J/m2 and 1030 J/m2, respectively, whereas the interfacial fracture energies of indirectly bonded MgFMLs were 1650 J/m2 and 2260 J/m2, respectively. Phosphating treatment and modified polypropylene interleaf were observed to improve the tensile strength and interfacial fracture toughness of MgFML. In addition, the rougher surface was more conducive to enhance the bonding strength and interfacial fracture toughness of MgFML.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Surface Modification and Superhydrophobicity · Fiber-reinforced polymer composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Thermal postbuckling analysis of fiber-metal laminated plates including interfacial damage10.1016/j.compositesb.2013.08.033 ↗
2. Analytical evaluation on uniaxial tensile deformation behavior of fiber metal laminate based on SRPP and its experimental confirmation10.1016/j.compositesb.2014.06.031 ↗
3. Long term behaviour of Glare10.1023/A:1025589812963 ↗
4. Fatigue and damage tolerance issues of Glare in aircraft structures10.1016/j.ijfatigue.2006.02.015 ↗
5. A review: fibre metal laminates, background, bonding types and applied test methods10.1016/j.matdes.2011.03.011 ↗
6. A review on the development and properties of continuous fiber/epoxy/aluminum hybrid composites for aircraft structures10.1590/S1516-14392006000300002 ↗
7. The mechanical behavior of GLARE laminates for aircraft structures10.1007/s11837-005-0067-4 ↗
8. Mechanical behaviors of Ti/CFRP/Ti laminates with different surface treatments of titanium sheets10.1016/j.compstruct.2016.12.033 ↗
9. Applicability of AZ31B-H24 magnesium in fibre metal laminates—an experimental impact research10.1016/j.compositesa.2012.04.008 ↗
10. The applicability of magnesium based fibre metal laminates in aerospace structures10.1016/j.compscitech.2008.06.017 ↗
11. Impact characterization of thermoformable fibre metal laminates of 2024-T3 aluminium and AZ31B-H24 magnesium based on self-reinforced polypropylene10.1016/j.compositesa.2014.02.011 ↗
12. A review on hot tearing of magnesium alloys10.1016/j.jma.2016.08.003 ↗
13. Synthesis and properties of hydroxyapatite-containing coating on AZ31 magnesium alloy by micro-arc oxidation10.1016/j.apsusc.2016.12.216 ↗
14. Plasma electrolytic oxidation of magnesium and its alloys: mechanism, properties and applications10.1016/j.jma.2017.02.004 ↗
15. Research on potassium permanganate-phosphate treatment of magnesium alloy surface and fiber/magnesium alloy composite laminate10.1002/maco.201609058 ↗
16. Effect of surface treatment on the interfacial adhesion performance of aluminum foil/CFRP laminates for cryogenic propellant tanks10.1016/j.matdes.2016.12.011 ↗
17. Effect of surface treatments on the durability of green polyurethane adhesive bonded aluminium alloy10.1016/j.ijadhadh.2014.07.007 ↗
18. Effect of adhesive quantity on failure behavior and mechanical properties of fiber metal laminates based on the aluminum-lithium alloy10.1016/j.compstruct.2016.05.098 ↗
19. Surface modifications of Ti alloy with tunable hierarchical structures and chemistry for improved metal–polymer interface used in deepwater composite riser10.1016/j.apsusc.2014.12.081 ↗
20. Effects of surface pre-treatments on Mode I and Mode II interlaminar strength of CFRP/Mg laminates10.1016/j.surfcoat.2017.04.010 ↗
21. Improvement of adhesion performance between aluminum alloy sheet and epoxy based on anodizing technique10.1016/j.ijadhadh.2016.05.007 ↗
22. Interface analysis of fiber metal laminates10.1080/15685543.2014.854527 ↗
23. Effects of surface pre-treatment and void content on GLARE laminate process characteristics10.1016/j.jmatprotec.2010.01.017 ↗
24. Modeling effects of asymmetry and fiber bridging on Mode I fracture behavior of bonded pultruded composite joints10.1016/j.engfracmech.2013.02.001 ↗
25. Investigation on mode-II interface fracture toughness of CFRP/Al laminates toughened by VGCF interleaves10.1007/s10853-014-8755-5 ↗
26. Experimental and numerical study on the improvement of interlaminar mechanical properties of Al/CFRP laminates10.1016/j.jmatprotec.2014.08.031 ↗
27. Hydrofluoric–nitric–sulphuric-acid surface treatment of tungsten for carbon fibre-reinforced composite hybrids in space applications10.1016/j.apsusc.2014.12.036 ↗
28. Effects of aluminum surface treatments on the interfacial fracture toughness of carbon-fiber aluminum laminates10.1016/j.engfracmech.2017.01.004 ↗
29. Interfacial fracture of the fibre-metal laminates based on fibre reinforced thermoplastics10.1016/j.matdes.2014.03.058 ↗
30. The fracture properties of a fibre–metal laminate based on magnesium alloy10.1016/j.compositesb.2005.06.002 ↗
31. Effect of surface treatment on the corrosion properties of magnesium-based fibre metal laminate10.1016/j.apsusc.2016.11.131 ↗
32. Research on surface treatment of magnesium alloy and its wettability with resin10.1080/02670836.2015.1104020 ↗
33. Surface free energy evaluation of well-ordered Langmuir-Blodgett surfaces: comparison of different approaches10.1016/j.colsurfa.2005.10.025 ↗
34. The fracture properties of a fiber metal laminate based on a self-reinforced thermoplastic composite material10.1002/pc.22677 ↗
35. Mechanical properties of a novel fiber-metal laminates based on a polypropylene composite10.1016/j.mechmat.2009.03.002 ↗
36. Interfacial fracture toughness of polyester-based fiber-metal laminates with primary contact and secondary adhesive bonding10.1023/B:JMSC.0000021464.13845.79 ↗
37. Sizing a single cantilever beam specimen for characterizing facesheet–core debonding in sandwich structure10.1177/0021998311401116 ↗
38. Strategies for the replacement of chromic acid anodising for the structural bonding of aluminium alloys10.1016/j.ijadhadh.2005.07.001 ↗