Erosion behaviour of WC–10Co–4Cr coating on 23-8-N nitronic steel by HVOF thermal spraying
Source abstract
Abstract
Abstract WC–10Co–4Cr coating was deposited by high-velocity oxy-fuel (HVOF) process on cast and solution treated (1220 °C/150 min) 23-8-N nitronic steel substrates. Solution treated substrate has shown higher toughness, ductility and impact energy with a marginal reduction in hardness as compared to cast substrate. This influence the coating deposition efficiency and erosion behaviour. Erosion resistance of coatings was evaluated by air jet erosion tester on two different impact angles (30° and 90°). Phases, microstructure and eroded surface of the coating were characterised by X-ray diffraction (XRD) analysis and field-emission scanning electron microscopy (FESEM) respectively. It is observed that coating on solution treated substrate was superior to cast substrate. The reason being that coating has dense and well-bonded structure with low porosity, less decarburization and inter-splat oxidation. Higher erosion resistance of coated solution treated 23-8-N nitronic steel was attributed to combination of high fracture toughness and hardness of coating including optimum mechanical properties of the substrate. FESEM analysis reveals that erosion response of WC–10Co–4Cr coating also dependent on the relative size of the impact crater with respect to the WC grain size. Coating is removed by combined mode of ductile and brittle erosion.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Erosion and Abrasive Machining · Advanced materials and composites · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. Developing silt consciousness in the minds of hydropower engineers
2. Metallurgy of erosion of under water parts in hydro electric projects
3. Effect of size and concentration of silt particles on erosion of Pelton turbine buckets10.1016/j.energy.2009.06.015 ↗
4. Effect of impingement angle on slurry erosion behaviour and mechanisms of 1017 steel and high-chromium white cast iron10.1016/j.wear.2006.11.018 ↗
5. Erodent particle characterization and the effect of particle size and shape on erosion10.1016/0043-1648(90)90176-B ↗
6. Slurry erosion of ductile materials under normal impact condition10.1016/j.wear.2007.03.022 ↗
7. Effect of the material surface hardness on the erosion of AISI31610.1016/j.wear.2005.02.004 ↗
8. The impact angle dependence of erosion damage caused by solid particle impact10.1016/S0043-1648(96)07430-3 ↗
9. Influence of microstructure on erosion resistance of steels10.1016/j.wear.2009.08.004 ↗
10. An experimental study of slurry erosion involving tensile stress for pressure pipe manifold10.1016/j.triboint.2014.07.025 ↗
11. Solid particle erosion behaviour of 13Cr–4Ni and 21Cr–4Ni–N steels10.1016/j.jallcom.2007.12.053 ↗
12. Slurry erosion behaviour of HVOF sprayed WC–10Co–4Cr and Al2O3+13TiO2 coatings on a turbine steel10.1016/j.wear.2012.04.016 ↗
13. Corrosion behaviour of cermet-based coatings with a bond coat in 0.5M H2SO410.1016/j.corsci.2008.09.020 ↗
14. Influence of spray parameters on the particle in-flight properties and the properties of HVOF coating of WC–CoCr10.1016/j.wear.2003.07.002 ↗
15. HVOF sprayed coatings of nano-agglomerated tungsten-carbide/cobalt powders for water droplet erosion application10.1016/j.wear.2015.02.034 ↗
16. Microstructure and cavitation erosion behavior of WC–Co–Cr coating on 1Cr18Ni9Ti stainless steel by HVOF thermal spraying10.1016/j.ijrmhm.2012.01.002 ↗
17. Effect of processing parameters on the microstructure and properties of WC–10Co–4Cr coatings formed by a new multi-chamber gas-dynamic accelerator10.1016/j.ceramint.2015.07.169 ↗
18. Microstructure and properties of WC-10% Co-4% Cr spray powders and coatings: part 1. Powder characterization10.1361/105996301770349402 ↗
19. Effects of carbide size and Co content on the microstructure and mechanical properties of HVOF-sprayed WC–Co coatings10.1016/j.surfcoat.2007.06.026 ↗
20. Comparative investigation on HVOF sprayed carbide-based coatings10.1016/j.apsusc.2013.03.010 ↗
21. Pawlowski · 2008
22. Effect of nanostructuring and Al alloying on corrosion behaviour of thermal sprayed WC–Co coatings10.1016/j.msea.2012.08.015 ↗
23. A study on powder mixing for high fracture toughness and wear resistance of WC–Co–Cr coatings sprayed by HVOF10.1016/j.surfcoat.2009.12.014 ↗
24. A comparative study on the microstructure and surface property evaluation of coatings produced from nanostructured and conventional WC–Co powders HVOF-sprayed on Al707510.1016/j.surfcoat.2015.06.017 ↗
25. Erosion of hard surface coatings for use in offshore gate valves10.1016/j.wear.2004.03.035 ↗
26. Comparison of slurry and dry erosion behaviour of some HVOF thermal sprayed coatings10.1016/S0043-1648(99)00034-4 ↗
27. Wear rates and specific energies of some ceramic cermet and metallic coatings determined in the Coriolis erosion tester10.1016/S0043-1648(99)00213-6 ↗
28. Erosion behaviour of ceramic bulk and coating materials caused by water droplet impingement10.1016/j.wear.2009.02.009 ↗
29. The development of sub-surface damage during high energy solid particle erosion of a thermally sprayed WC–Co–Cr coating10.1016/j.wear.2005.02.008 ↗
30. Solid particle erosion behavior of WC–CoCr nanostructured coating10.1080/10402004.2013.797532 ↗
31. Coating fracture toughness determined by Vickers indentation: an important parameter in cavitation erosion resistance of WC–Co thermally sprayed coatings10.1016/S0257-8972(03)00917-4 ↗
32. Effect of heat treatment on microstructure, mechanical properties and erosion resistance of cast 23-8-N nitronic steel10.1016/j.msea.2015.04.031 ↗
33. Local impact damage and erosion mechanisms in WC-6wt .% Co alloys10.1016/0025-5416(88)90725-2 ↗
34. Hardness and deformation of cemented tungsten carbide10.1016/0025-5416(78)90163-5 ↗
35. Parametric study of an HVOF process for the deposition of nanostructured WC–Co coatings10.1361/10599630523746 ↗
36. Quasi-static solid particle damage in brittle solids—I. Observations analysis and implications10.1016/0001-6160(76)90042-0 ↗
37. ASTM G76-13, Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 1, (2013) 1–6.
38. Short communication measurement of solid particle velocity in erosive wear10.1016/0043-1648(75)90154-4 ↗
39. Investigations on the corrosion-enhanced erosion behavior of carbon steel AISI 102010.1016/S1452-3981(23)10928-X ↗
40. A method for optimizing the particle flux in erosion testing with a gas-blast apparatus10.1016/0043-1648(94)90099-X ↗
41. Tribology of HVOF- and HVAF-sprayed WC −10Co4Cr hardmetal coatings: A comparative assessment10.1016/j.surfcoat.2015.01.048 ↗
42. www.matweb.com,(n.d.). http://www.matweb.com./(accessed 02.14.16).
43. Microstructure and scaling effects in the damage of WC–Co alloys by single impacts of hard particles10.1007/BF00547472 ↗
44. A model for the erosion of metals by spherical particles at normal incidence10.1016/0043-1648(81)90347-1 ↗
45. The erosion of heat-treated steels10.1016/0043-1648(83)90107-2 ↗
46. Effect of substrate hardness on splat morphology in high-velocity thermal spray coatings10.1361/105996306X147261 ↗
47. Preparation of copper–diamond composites with chromium carbide coatings on diamond particles for heat sink applications10.1016/j.applthermaleng.2013.05.038 ↗
48. The Effect of HVOF particle-substrate interactions on local variations in the coating microstructure and the corrosion resistance10.1007/s11666-010-9483-2 ↗
49. Grooving wear of single-crystal tungsten carbide10.1016/S0043-1648(99)00101-5 ↗
50. Solid particle erosion behaviour of thermal sprayed ceramic, metallic and polymer coatings10.1016/S0043-1648(98)00267-1 ↗