Study on particle fragmentation evolution characteristics and contact reconstruction response characteristics at the steel–coal–rock interface in compressed structures
Source abstract
Abstract
The crushing and micro-contact characteristics of powdery particles at the compressed structural steel–coal–rock interface have an important impact on the micro-contact mechanical characteristics of the structural steel surface and the macro-contact and friction characteristics of the interface with coal and rock as fixed supports and sliding bases. In order to explore the fragmentation evolution and microscopic contact mechanism of powdery particles at the compressed structural steel–coal–rock interface, the structural steel and coal–rock models were first reconstructed based on three-dimensional surface topography data and three-dimensional fractional theoretical models. Second, key characteristic parameters, such as ultra-fine powder particle size distribution, were obtained through ultra-fine powder performance measurement tests; a particle fragmentation model was established; and the particle fragmentation parameters were verified and adjusted using the results of constrained compression tests. Furthermore, considering the water content of powder particles, combined with the theory of particle adhesion and fragmentation, a three-body contact model of steel-powder–particle-coal–particle-rock is established by using the finite element–discrete element coupling method. Finally, using the obtained key characteristic parameters as simulation inputs, the time-varying breaking characteristics and microscopic contact characteristics of powder particles under different moisture content conditions were simulated and analyzed. The results show that during dynamic compression, the time period of 0.03–0.20 ms is the main fracture period. When the moisture content is 2%, the original large particle structure basically collapses, producing fine particles with a wide particle size distribution. The remaining grains will show Level 3 crushing characteristics after moisture content crushing. A large amount of the original large-grained structure is retained or only slightly shattered. Among them, when the moisture content is 12%, the dust crushing amount and crushing rate are the largest, while when the moisture content is 6%, the dust crushing amount and crushing rate are the smallest. There is a nonlinear relationship between coal crushing behavior and water content, and the crushing position is persistent and spatial random. After crushing, the contact between particles is redefined. As the water content increases, the time change between particles weakens and the contact direction between particles begins to gradually converge, making the contact behavior more stable and regular.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Granular flow and fluidized beds · Erosion and Abrasive Machining · Particle Dynamics in Fluid Flows
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Mechanical Engineering, Liaoning Technical University 1 , Fuxin 123000,
CCTEG Coal Mining Research Institute 2 , Beijing 100000,
Zhengzhou Coal Mining Machinery (Group) Co., Ltd. 3 , Zhengzhou 450000,
Shanxi Yanchang Petroleum Yulin Kekegai Coal Industry Co., Ltd. 4 , Yulin 719000,
Funding
National Natural Science Foundation of China · Natural Science Foundation of Liaoning Province · Scientific Research Fund of Liaoning Provincial Education Department · Liaoning Technical University
References (31)
Show source-provided references
1. The third-body approach: A mechanical view of wear10.1016/0043-1648(84)90025-5 ↗
2. Third-bodies in tribology10.1016/0043-1648(90)90070-q ↗
3. Research on mixed lubrication model of rough interface considering soft three-body contact10.3901/JME.2018.21.113 ↗
4. Research on friction and wear characteristics of the third body based on pin-disk test of brake friction pairs10.3969/j.issn.0254-0150.2022.06.008 ↗
5. Three-body contact friction analysis of MoS2 thin film in space rolling bearings10.16490/j.cnki.issn.1001-3660.2023.12.028 ↗
6. Effect of three-body particles on time-varying characteristics of tire braking friction10.3969/j.issn.2097-3853.2024.03.012 ↗
7. Experimental analysis of key brake pad parameters on brake system stability10.16579/j.issn.1001.9669.2025.03.005 ↗
8. Friction and wear properties of wheat straw powder third body on steel–steel friction pair10.3390/agriculture12060882 ↗
9. Dynamic wheel–rail adhesion characteristics on wet curved tracks considering surface roughness10.1063/5.0252179 ↗
10. Multiscale insights into tunneling-induced ground responses in coarse-grained soils10.1016/j.compgeo.2025.107319 ↗
11. The multiscale structure of granular matter and its mechanics
12. Study on force chain of two-dimensional photoelastic particle system based on G2 value method10.7520/1001-4888-22-269 ↗
13. Distribution characteristics of contact force chain of asphalt mixtures under different loading modes10.11918/202205094 ↗
14. Study on the force chain characteristics with coal dust layer and the three-body contact stiffness10.1016/j.partic.2024.05.014 ↗
15. Identification of force chains in wet coal dust layer and the effect of porosity on three-body contact stiffness10.1038/s41598-024-67340-y ↗
16. Numerical analysis of direct shear test based on change of force chain10.12404/j.issn.1671-1815.2307099 ↗
17. Force-transmitting of granular medium under ultrasonic vibration: Experiments and simulation10.1016/j.simpat.2023.102793 ↗
18. Simulation of force chains and particle breakage of granular material by numerical manifold method10.1016/j.powtec.2021.05.088 ↗
19. Numerical simulation of mechanical characteristics and force chain evolution during densification of granular systems10.12382/bgxb.2025.0690 ↗
20. A multivariate Weierstrass–Mandelbrot function10.1098/rspa.1985.0083 ↗
21. Contact analysis of elastic-plastic fractal surfaces10.1063/1.368536 ↗
22. Numerical study of the fine particle deposition behaviors on three-dimensional random rough walls10.1016/j.powtec.2020.07.066 ↗
23. A theoretical model for calculating the point-surface contact collision recovery coefficient10.13952/j.cnki.jofmdr.2007.03.019 ↗
24. Surface energy and the contact of elastic solids10.1098/rspa.1971.0141 ↗
25. Granular dynamics, contact mechanics and particle system simulations: A DEM study10.1007/978-3-319-18711-2 ↗
26. A method for characterizing the moisture content of wet coal particles based on surface energy10.13732/j.issn.1008-5548.2021.01.009 ↗
27. Microstructure of quarry rocks and relationships to particle breakage and crushing10.1016/j.minpro.2008.01.007 ↗
28. Modeling of particle fracture by repeated impacts using continuum damage mechanics10.1016/s0032-5910(01)00438-7 ↗
29. Measurement and characterization of particle strength using a new robotic compression tester10.1016/j.powtec.2004.04.007 ↗
30. Breakage of single particles: Quasi-static10.1016/S0167-3785(07)12004-2 ↗
31. Modeling ore degradation during handling using continuum damage mechanics10.1016/j.minpro.2010.07.011 ↗