Development of nonresonant elliptical vibration cutting device based on parallel piezoelectric actuator
Source abstract
Abstract
Because of its unique intermittent cutting and friction reversal characteristics, elliptical vibration cutting (EVC) has become the most promising method for machining of otherwise difficult-to-machine materials in recent years. However, some problems remain in the research towards development of EVC devices. In this paper, with the intention of solving the existing problems of EVC devices, a nonresonant-type EVC device that is driven by two parallel piezoelectric stacks is developed. After the principle of the device is introduced, the stiffness of the EVC device is calculated, and device simulations and experimental evaluations are performed. In addition, the performance of the EVC device is also tested. The experimental results show that the maximum strokes of the two directional mechanisms operating along the X- and Z-axes can reach 16.78 μm and 15.35 μm, respectively, and the motion resolutions in the X-axis and Z-axis directions both reach approximately 50 nm. Finally, a curved surface cutting experiment is carried out to verify the performance of the developed device.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Surface Polishing Techniques · Advanced machining processes and optimization · Piezoelectric Actuators and Control
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Changchun University of Technology School of Mechatronic Engineering, , Changchun 130012, China
Funding
Micro-Nano and Ultra-Precision Key Laboratory of Jilin Province · The Department of Science and Technology of Jilin Province · National Natural Science Foundation of China
References (30)
Show source-provided references
1. Manufacturing and measurement of freeform optics10.1016/j.cirp.2013.05.003 ↗
2. The mechanism of ductile chip formation in cutting of brittle materials10.1007/s00170-006-0531-5 ↗
3. Design tools for freeform optics10.1117/12.617680 ↗
4. Review of micro/nano machining by utilizing elliptical vibration cutting10.1016/j.ijmachtools.2016.04.008 ↗
5. Review of vibration-assisted machining10.1016/j.precisioneng.2007.08.003 ↗
6. Fundamental investigation of ultra-precision ductile machining of tungsten carbide by applying elliptical vibration cutting with single crystal diamond10.1016/j.jmatprotec.2014.05.024 ↗
7. Study on elliptical vibration cutting10.1016/s0007-8506(07)62158-1 ↗
8. Ultrasonic elliptical vibration cutting10.1016/s0007-8506(07)62269-0 ↗
9. Ultaprecision diamond cutting of hardened steel by applying elliptical vibration cutting10.1016/s0007-8506(07)63222-3 ↗
10. Elliptical vibration cutting of tungsten alloy molds for optical glass parts10.1016/j.cirp.2007.05.032 ↗
11. Analysis of regenerative chatter suppression with adding the ultrasonic elliptical vibration on the cutting tool10.1016/j.precisioneng.2010.12.004 ↗
12. Investigation of tool wear suppression in ultraprecision diamond machining of die steel10.1016/j.precisioneng.2011.05.003 ↗
13. Micro/nano sculpturing of hardened steel by controlling vibration amplitude in elliptical vibration cutting10.1016/j.precisioneng.2010.09.006 ↗
14. Analysis of 3D elliptical vibration cutting with thin shear plane model10.1016/j.cirp.2008.03.073 ↗
15. Simulation of elliptical vibration cutting process with thin shear plane model10.1016/j.cirp.2008.03.073 ↗
16. A study on micro-grooving characteristics of planar lightwave circuit and glass using ultrasonic vibration cutting10.1016/s0924-0136(02)00740-9 ↗
17. A study on ultrasonic elliptical vibration cutting of tungsten carbide10.1016/j.jmatprotec.2008.10.047 ↗
18. Machinability study of tungsten carbide using PCD tools under ultrasonic elliptical vibration cutting10.1016/j.ijmachtools.2009.07.006 ↗
19. A study on the effect of tool nose radius inultrasonic elliptical vibration cutting of tungsten carbide10.1016/j.jmatprotec.2009.06.013 ↗
20. Development of a tertiary motion generator for elliptical vibration texturing10.1016/j.precisioneng.2012.10.005 ↗
21. Micro-structure fabrication using elliptical vibration-assisted machining (EVAM)10.1016/j.precisioneng.2007.08.003 ↗
22. Characteristics of chip formation in micro V-grooving using elliptical vibration cutting10.1088/0960-1317/17/8/007 ↗
23. Characteristics of elliptical vibration cutting in micro-V grooving with variations in the elliptical cutting locus and excitation frequency10.1088/0960-1317/18/2/025002 ↗
24. Direct machining of micro patterns on nickel alloy and mold steel by vibration assisted cutting10.1007/s12541-011-0075-y ↗
25. Machining of micro-channels and pyramid patterns using elliptical vibration cutting10.1007/s00170-009-2451-7 ↗
26. Development of a programmable vibration cutting tool for diamond turning of hardened mold steels10.1007/s00170-007-1311-6 ↗
27. Development of a non-resonant 3D elliptical vibration cutting apparatus for diamond turning10.1111/ext.12051 ↗
28. Development of a double-frequency elliptical vibration cutting apparatus for freeform surface diamond machining10.1007/s00170-016-8596-2 ↗
29. Kinematic analysis of a translational 3-dof micro-parallel mechanism using the matrix method10.1163/156855302760121927 ↗
30. Corner-filleted flexure hinges10.1115/1.1372190 ↗