A high-performance biodegradable Mg-Zn- Ca-Sn alloy with synergistic improvement of yield strength and corrosion rate achieved by precise control of extrusion and microstructural design
Source abstract
Abstract
Magnesium alloys are emerging as promising candidates for biomedical applications due to their biodegradability, biocompatibility, and appropriate mechanical properties. However, achieving a balance between high strength and corrosion resistance remains a critical challenge. This study presents the development of a low-alloy Mg-1.2Zn-0.32Ca-0.25Sn (ZXT100) alloy aimed at overcoming the trade-off between high strength and high corrosion resistance. Comprehensive microstructural, mechanical, and electrochemical analyses were performed to elucidate the alloy's performance and underlying mechanisms. The ZXT100 alloy demonstrates the promising tensile yield strength (∼345 ± 13 MPa) and degradation rate (∼0.209 ± 0.012 mm/y), surpassing most commercially available and recently reported medical magnesium alloys. Grain boundary strengthening was found to be the primary mechanism for the improved yield strength, contributing approximately 65.8%. The modification of heterogeneous fiber structure facilitates balance between elasticity and strength. In vitro cytocompatibility and osteogenic differentiation assays confirmed favorable biocompatibility and enhanced cell migration compared to high-purity Mg. In vivo studies in rats and rabbits demonstrated controlled degradation, minimal gas formation, and favorable osteointegration with no systemic toxicity. This work provides a feasible strategy for designing high-performance biodegradable Mg alloys for load-bearing orthopedic implants. STATEMENT OF SIGNIFICANCE: Biodegradable magnesium alloys offer a promising alternative to permanent metallic implants, eliminating the need for secondary removal surgery. However, achieving both high strength and controlled degradation-essential for load-bearing orthopedic applications-remains a major challenge. Building on our previous compositional optimization, this study demonstrates that precise control of extrusion temperature enables microstructural design that simultaneously achieves exceptional yield strength (349 ± 13 MPa) and a low degradation rate (0.209 ± 0.012 mm/y) in a low-alloyed Mg-Zn-Ca-Sn system. The alloy also exhibits favorable biocompatibility in vitro and in vivo, positioning it as a strong candidate for next-generation biodegradable orthopedic implants.
Source: europepmc · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Orthopaedic implants and arthroplasty · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (83)
Show source-provided references
1. Development of new metallic alloys for biomedical applications10.1016/j.actbio.2012.06.037 ↗
2. Mechanical properties of biomedical titanium alloys10.1016/S0921-5093(97)00806-X ↗
3. Manufacturing and processing of NiTi implants: a review10.1016/j.pmatsci.2011.11.001 ↗
4. A review on nickel-free nitrogen containing austenitic stainless steels for biomedical applications10.1016/j.msec.2013.06.002 ↗
5. Dissimilar transient liquid phase bonding of Ti–6Al–4V and Co–Cr–Mo biomaterials using a Cu interlayer: microstructure and mechanical properties10.1016/j.jallcom.2020.154510 ↗
6. Magnesium alloys as extremely promising alternatives for temporary orthopedic implants – A review10.1016/j.jma.2023.08.002 ↗
7. Recent progress in in vivo studies and clinical applications of magnesium based biodegradable implants – A review10.1016/j.jma.2020.11.001 ↗
8. Recent advances in the development of Mg-Ca-Zn alloys as biodegradable orthopedic implants
9. Effect of grain size on the mechanical properties and bio-corrosion resistance of pure magnesium10.1016/j.jmrt.2022.06.048 ↗
10. Approaching “stainless magnesium” by Ca micro-alloying10.1039/D0MH01380C ↗
11. Mechanical and bio-corrosion properties of quaternary Mg–Ca–Mn–Zn alloys compared with binary Mg–Ca alloys10.1016/j.matdes.2013.06.055 ↗
12. Simultaneously enhanced strength and ductility of Mg-Zn-Zr-Ca alloy with fully recrystallized ultrafine grained structures10.1016/j.scriptamat.2016.12.024 ↗
13. Realizing ultra-high strength and excellent ductility in a low-alloyed biomedical Mg-Zn-Ca-MgO composite10.1016/j.jma.2024.01.004 ↗
14. Possible relationship between Al/ferritin complex and Alzheimer's disease10.1016/j.clinbiochem.2012.10.023 ↗
15. Multimodal ex vivo methods reveal that Gd-rich corrosion byproducts remain at the implant site of biodegradable Mg-Gd screws10.1016/j.actbio.2021.09.047 ↗
16. Recent advances on the development of magnesium alloys for biodegradable implants10.1016/j.actbio.2014.07.005 ↗
17. Ultra-fine grain size and exceptionally high strength in dilute Mg–Ca alloys achieved by conventional one-step extrusion10.1016/j.matlet.2018.11.080 ↗
18. Achieving high strength near 400 MPa in an ultra-fine grained Mg–Bi–Ca ternary alloy via low-temperature extrusion10.1016/j.jmrt.2023.08.202 ↗
19. Mechanism of alloying element co-segregation at the grain boundary and its influence on mechanical properties in Mg-Zn-Ca alloy10.1016/j.jmst.2025.12.016 ↗
20. Effect of Sn addition on the microstructure and corrosion behavior of dilute wrought Mg-Zn-Ca series alloys10.1016/j.corsci.2024.112180 ↗
21. Synergistic improvement of corrosion-strength of Mg-Zn-Ca-Sn dilute alloys by adjusting the Sn/Ca atomic ratio10.1016/j.jma.2025.10.003 ↗
22. Biomechanical optimization of the magnesium alloy bionic cannulated screw for stabilizing femoral neck fractures: a finite element analysis10.3389/fbioe.2024.1448527 ↗
23. The effect of RE and Ca on corrosion resistance of AZ9110.4028/www.scientific.net/MSF.488-489.869 ↗
24. Corrosion behaviour in salt spray and in 3.5% NaCl solution saturated with Mg(OH)2 of as-cast and solution heat-treated binary Mg–X alloys: x=Mn, Sn, Ca, Zn, Al, Zr, Si, Sr10.1016/j.corsci.2013.06.030 ↗
25. Tailoring the micromorphology of the as-cast Mg–Sn–In alloys to corrosion-resistant microstructures via adjusting In concentration
26. Self-generating construction of applicable corrosion-resistant surface structure of magnesium alloy10.1016/j.corsci.2021.109378 ↗
27. The influence of Gd content on the microstructure, mechanical properties, corrosion behavior and corrosion film deposition mechanisms of as-extruded Mg–Zn–Mn–Sr–Gd alloys for biomedical applications10.1007/s10853-021-06622-6 ↗
28. Towards development of a high-strength stainless Mg alloy with Al-assisted growth of passive film10.1038/s41467-022-33480-w ↗
29. Exploring mechanism of corrosion inhibition of WE43 and AZ31 alloys by aqueous molybdate in Hank’s solution by multisine impedimetric monitoring10.1016/j.corsci.2024.111979 ↗
30. Deformation behavior of LPSO phases with regulated morphology and distribution and their role on dynamic recrystallization in hot-rolled Mg–Gd–Y–Zn–Zr alloy10.1016/j.jmrt.2023.08.307 ↗
31. Large plasticity in magnesium mediated by pyramidal dislocations10.1126/science.aaw2843 ↗
32. Ternäre E-Phasen von Hauptgruppenelementen I10.1515/znb-1969-0705 ↗
33. Enhancing corrosion resistance of Mg-Al-Mn-Ca-Y dilute alloy via novel core-shell structured Al8Mn4Y-Al2Ca and controllable solute segregation10.1016/j.jma.2023.10.009 ↗
34. Enhanced superplasticity of ultrafine-grained WEQ612 magnesium alloy via the coupling effect of grain boundary segregation and dense precipitation10.1016/j.msea.2024.146337 ↗
35. The effects of Ca and Mn on the microstructure, texture and mechanical properties of Mg-4 Zn alloy10.1016/j.jma.2020.03.012 ↗
36. Excellent synergy of formability and strength of a Mg-Zn-Y-Ca-Zr alloy by tailoring segregation-assisted weak elliptical ring texture10.1016/j.jma.2024.06.029 ↗
37. Dramatic enhancement of the corrosion resistance of dilute Mg–Al–Mn–Ca alloy through Gd alloying10.1016/j.corsci.2024.112351 ↗
38. Development of highly corrosion-resistant Mg-Al-Y extruded alloy via regulating the Mg17Al12 phase10.1016/j.corsci.2024.112124 ↗
39. Achieving ultra-high corrosion-resistant Mg-Zn-Sc alloys by forming Sc-assisted protective corrosion product film10.1016/j.jmst.2023.08.068 ↗
40. Measurement of the corrosion rate of magnesium alloys using Tafel extrapolation10.1016/j.corsci.2009.10.016 ↗
41. Corrosion inhibition effects of Corrosion products on high-purity Mg and AZ91D under thin electrolyte layers10.1149/1945-7111/ac9353 ↗
42. Microstructure and protection characteristics of the naturally formed oxide films on Mg–xZn alloys10.1016/j.corsci.2013.03.021 ↗
43. Improving corrosion resistance of Mg–Li alloys by Sn microalloying10.1016/j.jmrt.2023.07.205 ↗
44. A high-performance tin phosphide/carbon composite anode for lithium-ion batteries10.1039/D0DT03139A ↗
45. High-efficiency photocatalytic activity of type II SnO/Sn3O4 heterostructures via interfacial charge transfer10.1039/C4CE00884G ↗
46. Zn ion-modulated polyamide membrane with enhanced facilitated transport effect for CO2 separation10.1016/j.seppur.2022.121051 ↗
47. Effect of Sn addition on the mechanical properties and bio-corrosion behavior of cytocompatible Mg–4Zn based alloys10.1016/j.jma.2019.02.002 ↗
48. Review of Mg alloy corrosion rates10.1016/j.jma.2020.08.002 ↗
49. Structure, mechanical and corrosion properties of extruded Mg-Nd-Zn, Mg-Y-Zn and Mg-Y-Nd alloys10.1080/02670836.2019.1570680 ↗
50. Effect of grain refinement and crystallographic texture produced by friction stir processing on the biodegradation behavior of a Mg-Nd-Zn alloy10.1016/j.jmst.2018.11.025 ↗
51. Effect of thermal treatment on the bio-corrosion and mechanical properties of ultrafine-grained ZK60 magnesium alloy10.1016/j.jmbbm.2015.07.019 ↗
52. Microstructure, mechanical property, in vitro biodegradation behavior and biocompatibility of as-extruded Mg-2Zn-0.2Zr-xNd (x = 0.2, 0.6, 1.0) alloys10.1016/j.matchar.2023.113214 ↗
53. Influence of Sc on the microstructure, degradation behavior, biocompatibility in vitro and mechanical property of Mg-2Zn-0.2Zr alloy10.1016/j.matdes.2022.110863 ↗
54. Influence of second phase precipitates on mechanical and in-vitro corrosion behaviour of Mg-4Zn-0.5Ca-0.8Mn alloy in optimum homogenized conditions10.1016/j.jma.2022.11.011 ↗
55. Improving in vitro and in vivo corrosion resistance and biocompatibility of Mg-1Zn-1Sn alloys by microalloying with Sr
56. In- vitro corrosion behavior of the cast and extruded biodegradable Mg-Zn-Cu alloys in simulated body fluid (SBF)10.1016/j.jma.2021.01.002 ↗
57. Microstructure, mechanical and corrosion properties of novel quaternary biodegradable extruded Mg–1Zn–0.2Ca-xAg alloys10.1088/2053-1591/ab6a52 ↗
58. Effects of extrusion and heat treatment on the mechanical properties and biocorrosion behaviors of a Mg-Nd-Zn-Zr alloy10.1016/j.jmbbm.2011.05.026 ↗
59. Comparison of biodegradable behaviors of AZ31 and Mg–Nd–Zn–Zr alloys in Hank's physiological solution10.1016/j.mseb.2011.09.042 ↗
60. In vitro degradation behavior and cytocompatibility of Mg-6Zn-Mn alloy10.1016/j.matlet.2018.05.034 ↗
61. Microstructure, mechanical properties and corrosion behavior of extruded Mg-Zn-Ca alloys with same Zn/Ca atomic ratio
62. Influence of Sr on microstructure evolution, mechanical and corrosion properties of extruded Mg-2Zn-0.5Ca alloy10.1016/j.jma.2023.03.008 ↗
63. The critical roles of twinning and prismatic 〈a〉 slipping in affecting the dynamic recrystallization of hot-rolled Mg-Gd-Zr thick plate10.1016/j.jma.2025.07.016 ↗
64. Heterogeneous fiberous structured Mg-Zn-Zr alloy with superior strength-ductility synergy10.1016/j.jmst.2022.06.021 ↗
65. The interaction of grain refinement and ageing in magnesium–zinc–zirconium (ZK) alloys10.1016/j.actamat.2015.05.012 ↗
66. Strain partitioning by recurrent shear localization during equal-channel angular pressing of an AA6060 aluminum alloy10.1016/j.actamat.2019.07.009 ↗
67. In situ EBSD investigation of deformation processes and strain partitioning in bi-modal Ti-6Al-4V using lattice rotations10.1016/j.actamat.2019.04.033 ↗
68. Heterogeneous lamella structure unites ultrafine-grain strength with coarse-grain ductility10.1073/pnas.1517193112 ↗
69. Anomalous effects of strain rate on the room-temperature ductility of a cast Mg-Gd-Y-Zr alloy10.1016/j.actamat.2018.08.013 ↗
70. Interface affected zone for optimal strength and ductility in heterogeneous laminate10.1016/j.mattod.2018.03.006 ↗
71. Strain hardening and ductility in a coarse-grain/nanostructure laminate material10.1016/j.scriptamat.2015.03.006 ↗
72. Hall-petch relationship and deformation mechanism of pure Mg at room temperature10.1016/j.jallcom.2022.165924 ↗
73. Influence of grain size and texture on Hall–Petch relationship for a magnesium alloy10.1016/j.scriptamat.2011.08.028 ↗
74. Microstructure and strengthening mechanism of hot-extruded ultralight Mg-Li-Al-Sn alloys with high strength10.1016/j.jmst.2021.07.009 ↗
75. High plasticity mechanism of high strain rate rolled Mg-Ga alloy sheets10.1016/j.jmst.2021.05.064 ↗
76. Precipitation strengthening and reversed yield stress asymmetry in Mg alloys containing rare-earth elements: a quantitative study10.1016/j.actamat.2016.11.019 ↗
77. Thrombogenic characterization of alloyed and surface-modified magnesium bioresorbable metals for cardiovascular device applications10.1016/j.biomaterials.2025.123935 ↗
78. Compositional "plainification" in biodegradable magnesium-rare earth alloys - achieving well-balanced performance in an ultra-lean Mg-Pr alloy10.1016/j.biomaterials.2025.123681 ↗
79. Saijilafu, magnesium oxide/poly(l-lactide-co-ε-caprolactone) scaffolds loaded with neural morphogens promote spinal cord repair through targeting the calcium influx and neuronal differentiation of neural stem cells
80. Biomimetic porous magnesium alloy scaffolds promote the repair of osteoporotic bone defects in rats through activating the wnt/β-catenin signaling pathway10.1021/acsbiomaterials.2c01097 ↗
81. Ion channel functional protein kinase TRPM7 regulates Mg ions to promote the osteoinduction of human osteoblast via PI3K pathway: in vitro simulation of the bone-repairing effect of Mg-based alloy implant10.1016/j.actbio.2017.08.051 ↗
82. Magnesium enhances osteogenesis of BMSCs by tuning osteoimmunomodulation
83. A magnesium screw with optimized geometry exhibits improved corrosion resistance and favors bone fracture healing10.1016/j.actbio.2024.03.002 ↗