Mechanisms underlying the limited injectability of hydraulic calcium phosphate paste. Part ІІ: Particle separation study
Source abstract
Abstract
Calcium phosphate cements (CPCs) are of great interest for bone augmentation procedures. In these a hydraulic calcium phosphate paste is injected through a small bore needle into the bone. The injectability of these pastes is relatively poor, resulting into partial injection only. In earlier studies we have shown that phase separation brings the injection process to a halt. Phase separation is characterized by a faster flow of the liquid than of the solid during paste extrusion. So far it is unclear whether or not particle separation contributes to the poor injectability of such hydraulic pastes. It is hypothesized that fine particles behave like a liquid and thus separate under the injection pressure, leaving larger particles behind. A factorial experimental design was used to examine this hypothesis. The particle size distribution (PSD) of the extrudate was measured over the course of each injection experiment using laser diffraction. The solid content of the paste was further inspected using scanning electron microscopy. A total of 48 experiments covering four factors at two levels each were performed. One factor was the ultrasound exposure duration, to ensure the dispersion quality of the particles during the PSD measurements. Another factor was the location of the samples over the course of the injection, so as to compare the extrudate with the PSDs remaining in the syringe. The liquid:powder ratio (LPR) in the injected paste was another factor investigated. Specifically, two different pastes with 40% and 50% LPR were examined. The dispersal medium was a fourth factor investigated, to ensure adequate dispersion of the particles during the PSD measurements. Analysis of variance showed that sample location did not significantly affect PSD. No apparent PSD change for the extruded paste and the paste remaining in the syringe could be detected by scanning electron microscopy. In conclusion, the present study did not show any evidence suggesting that particle separation occurred over the course of injection and thus that phase separation remains the main phenomenon leading to the poor injectability of CPCs.
Source: europepmc · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Bone Tissue Engineering Materials · Dental Implant Techniques and Outcomes · Endodontics and Root Canal Treatments
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (12)
Show source-provided references
1. Effects of various adjuvants (lactic acid, glycerol, and chitosan) on the injectability of a calcium phosphate cement10.1016/S8756-3282(99)00130-1 ↗
2. Some factors controlling the injectability of calcium phosphate bone cements10.1023/A:1008811215655 ↗
3. Ionic modification of calcium phosphate cement viscosity. Part I. Hypodermic injection and strength improvement of apatite cement10.1016/j.biomaterials.2003.08.066 ↗
4. Ionic modification of calcium phosphate cement viscosity. Part II. Hypodermic injection and strength improvement of brushite cement10.1016/j.biomaterials.2003.09.085 ↗
5. Mechanical and rheological improvement of a calcium phosphate cement by the addition of a polymeric drug10.1002/1097-4636(200110)57:1<113::AID-JBM1149>3.0.CO;2-5 ↗
6. Rheological enhancement of mechanically activated α-tricalcium phosphate cements10.1002/jbm.b.30148 ↗
7. Injectability of calcium phosphate pastes10.1016/j.biomaterials.2004.05.010 ↗
8. Mechanisms underlying the limited injectability of hydraulic calcium phosphate paste10.1016/j.actbio.2008.03.004 ↗
9. Prediction of the viscosity of multimodal suspensions from uniomodal viscosity data10.1122/1.549109 ↗
10. Chiara · 2006
11. Particle size distribution of fine powders by LASER diffraction spectrometry. Case of cementitious materials10.1007/BF02486485 ↗
12. Hackley · 2004