Selenization of printed Cu–In–Se alloy nanopowder layers for fabrication of CuInSe2 thin film solar cells
Source abstract
Abstract
Abstract One of the promising low cost and non-vacuum approaches for the fabrication of semiconductor CuInSe 2 and Cu(In,Ga)(S,Se) 2 thin film absorbers is the printing of precursor materials followed by a sintering/selenization process. The selenization process parameters such as temperature, duration, and selenium vapor pressure strongly influence the morphology and electronic properties of the absorber film. In this study, the effect of pre-annealing in an inert atmosphere and selenization on printed mechanically synthesized CuInSe 0.5 alloy nanopowder precursor films was investigated. 1–2 μm thick CuInSe 0.5 alloy nanopowder layers were deposited on a Mo-sputtered glass substrate by means of doctor blade coating of a nanopowder based precursor suspension. Pre-annealing was performed on a hot plate inside a nitrogen gas filled glove box. Selenization was performed in a home-made rapid thermal processing (RTP) furnace with two RTP heating zones for independent temperature control of the selenium source and the coated substrate. The temperature of the selenium source was fixed at 390–410 °C during the selenization to provide a constant supply of selenium vapor. A two-step process, i.e., a pre-annealing in nitrogen atmosphere at 400 °C for 30 min followed by selenization at 530 °C for 15 min was found to result in better densification and grain growth of the CuInSe 2 phase, compared to a single step selenization at 530 °C for 15 min. The solar cell fabricated by the two-step process had an efficiency of 5.4% and a fill factor of 52%, while the device fabricated by the single step selenization had an efficiency of 1.1% and a fill factor of 31%.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Copper-based nanomaterials and applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (14)
Show source-provided references
1. Colloidal CIGS and CZTS nanocrystals: a precursor route to printed photovoltaics10.1016/j.jssc.2011.11.002 ↗
2. Non vacuum methods for formation of Cu(In, Ga)(Se, S)2 thin film photovoltaic absorbers10.1002/pip.914 ↗
3. Non-vacuum deposition of CIGS absorber films for low-cost thin film solar cells10.1007/s11814-013-0101-0 ↗
4. Ink formulation and low-temperature incorporation of sodium to yield 12% efficient Cu (In, Ga)(S, Se)2 solar cells from sulfide nanocrystal inks10.1002/pip.2200 ↗
5. CIS film growth by metallic ink coating and selenization10.1016/S0927-0248(99)00075-6 ↗
6. Low cost processing of CIGS thin film solar cells10.1016/j.solener.2004.08.015 ↗
7. CIS module pilot processing applying concurrent rapid selenization and sulfurization of large area thin film precursors10.1016/S0040-6090(03)00249-9 ↗
8. Rapid CIS-process for high efficiency PV-modules: development towards large area processing10.1016/S0040-6090(00)01800-9 ↗
9. Mechanical synthesis of high purity Cu–In–Se alloy nanopowder as precursor for printed CISe thin film solar cells10.1016/j.apt.2014.03.003 ↗
10. Effect of selenium content of CuInSex alloy nanopowder precursors on recrystallization of printed CuInSe2 absorber layers during selenization heat treatment10.1016/j.tsf.2014.10.003 ↗
11. Phase diagram of the Culn-2Se system for CulnSe2 crystal growth by controlling Se contents10.1016/S0022-0248(97)00147-4 ↗
12. Sintering and grain growth
13. In situ investigation of the selenization kinetics of Cu–Ga precursors using time-resolved high-temperature X-ray diffraction10.1016/j.tsf.2006.12.173 ↗
14. In situ investigation on selenization kinetics of Cu–In precursor using time-resolved, high temperature X-ray diffraction10.1016/j.jcrysgro.2006.05.066 ↗