journal article·2023-09

Influence of micro– and macrostructure when determining the contact resistivity of interconnects based on electrically conductive adhesives

M. Ignacia Devoto Acevedo, Stephan Großer, Karl Wienands, Tudor Timofte, Andreas Halm, Ralph Gottschalg, Daniel Tune

Publisher page

Abstract

The contact resistivity of interfaces in solar module interconnects has a direct impact on the series resistance of the entire module and fill factor. Thus, this impacts the performance of entire photovoltaic systems. Accurate measurement of the contact resistance is a key component of optimizing the performance of such interconnects. However, this is difficult for electrically conductive adhesive (ECA) based interconnects. This work shows that transmission line method (TLM) test structures based on ECA display non–negligible inhomogeneities leading to inaccuracies when determining the contact resistivity. Seven methods based on two models — the front– and end–contact TLM models (or a combination of both) — were investigated for four commercially available ECAs used in solar modules and their impacts on the extrapolation of the contact resistivity were quantified. It was determined that even when macroscale inhomogeneities (e.g., variations in the thickness of the ECA) are not present, microscopic structural effects influence the sheet and contact resistance. In particular, variations in the distribution of fillers significantly alter the bulk resistivity of the composites and this variability is also clearly correlated with differences in the geometry of the fillers. It is concluded that the best approach to reduce inaccuracies in the determination of the contact resistivity of ECA–based interconnects is to calculate the sheet and contact resistance locally (using three consecutive contacts) employing a redundant and modified test structure. Afterwards, the contact resistivity ought to be computed using the end–contact TLM model and the median should be assigned as the contact resistivity of the sample.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Electrostatic Discharge in Electronics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (51)

Show source-provided references
1. The sun is rising on conductive adhesives
2. Study of isotropically conductive bondings filled with aggregates of nano-sited Ag-particles10.1109/95.558539 ↗
3. Effect of Ag particle size on electrical conductivity of isotropically conductive adhesives10.1109/6104.816098 ↗
4. Electrically conductive nanocomposite adhesives based on epoxy resin filled with silver coated nanocarbon black10.1007/s10854-018-9284-9 ↗
5. Effect of silver powders on a low curing temperature silver conductive adhesive10.1007/s10854-018-9971-6 ↗
6. Adhesives in electronics10.1016/S1874-5695(02)80007-0 ↗
7. Electrical characteristics of a new class of conductive adhesive10.2320/matertrans.46.2276 ↗
8. Conductivity enhancement of nano silver-filled conductive adhesives by particle surface functionalization10.1007/s11664-005-0202-6 ↗
9. Research on electrical conductive adhesives filled with mixed filler10.1016/j.ijadhadh.2013.07.001 ↗
10. Conductivity improvement of silver flakes filled electrical conductive adhesives via introducing silver-graphene nanocomposites10.1007/s10854-013-1671-7 ↗
11. A comprehensive study of silver nanowires filled electrically conductive adhesives10.1007/s10854-015-3446-9 ↗
12. Isotropical conductive adhesives with very-long silver nanowires as conductive fillers10.1007/s10854-016-5487-0 ↗
13. Effects of silver microparticles and nanoparticles on thermal and electrical characteristics of electrically conductive adhesives10.1007/s11664-017-5690-7 ↗
14. Lu · 2017
15. Performance of various fillers in adhesives applications: a review10.1007/s00289-021-04022-z ↗
16. Contact resistance on diffused resistors
17. Messung des übergangswiderstandes zwischen metall und diffusionsschicht in Si-planarelementen10.1016/0038-1101(69)90045-8 ↗
18. Obtaining the specific contact resistance from transmission line model measurements10.1109/EDL.1982.25502 ↗
19. Solar cell contact resistance—a review10.1109/T-ED.1984.21583 ↗
20. Determining specific contact resistivity from contact end resistance measurements10.1109/EDL.1984.25875 ↗
21. Current crowding effects and determination of specific contact resistivity from contact end resistance (CER) measurements10.1109/EDL.1985.26259 ↗
22. Evaluation of contact resistance for isotropic electrically conductive adhesives10.1109/96.386265 ↗
23. Mechanisms underlying the unstable contact resistance of conductive adhesives
24. A novel approach to stabilize contact resistance of electrically conductive adhesives on lead-free alloy surfaces10.1007/s11664-004-0278-4 ↗
25. Optimization of electrically conductive adhesive bonds in photovoltaic modules10.1109/JPHOTOV.2018.2828829 ↗
26. Heterojunction module technology
27. Comprehensive study of material dependency for silver based conductive glues10.1016/j.egypro.2014.08.017 ↗
28. Cross testing electrically conductive adhesives and conductive back-sheets for the ECN back-contact cell and module technology10.1016/j.egypro.2015.03.301 ↗
29. Testing interconnections using conductive adhesives for application in PV modules
30. Test structures for ohmic contact characterization
31. Contact resistance and methods for its determination10.1016/0040-6090(83)90577-1 ↗
32. Contact resistance: its measurement and relative importance to power loss in a solar cell10.1109/T-ED.1984.21584 ↗
33. Analytical and finite-element modeling of a cross kelvin resistor test structure for low specific contact resistivity10.1109/TED.2009.2028623 ↗
34. Modeling and measurement of contact resistances10.1109/T-ED.1987.22957 ↗
35. The effect of sheet resistance modifications underneath the contact on the extraction of the contact resistivity: application to the cross Kelvin resistor10.1109/16.2466 ↗
36. Electrical modelling of Kelvin structures for the derivation of low specific contact resistivity
37. Kelvin test structure modeling of metal-silicide-silicon contacts10.1557/PROC-514-363 ↗
38. New challenges to the modelling and electrical characterisation of ohmic contacts for ULSI devices10.1016/S0026-2714(00)00006-8 ↗
39. Accurate contact resistivity extraction on Kelvin structures with upper and lower resistive layers10.1109/16.848288 ↗
40. Contact resistance measurement of bonded copper interconnects for three-dimensional integration technology10.1109/LED.2003.821591 ↗
41. An evaluation of test structures for measuring the contact resistance of 3-D bonded interconnects
42. Geipel · 2018
43. Statistical modeling of transmission line model test structures. I. The effect of inhomogeneities on the extracted contact parameters10.1109/16.62287 ↗
44. Models for contacts to planar devices10.1016/0038-1101(72)90048-2 ↗
45. Shockley · 1964
46. Statistical modeling of transmission line model test structures. II. TLM test structure with four or more terminals: a novel method to characterize nonideal planar contacts in presence of inhomogeneities10.1109/16.62288 ↗
47. Electrical conduction models for isotropically conductive adhesives10.1142/S096031319500030X ↗
48. Electrical conduction models for isotropically conductive adhesive joints10.1109/95.558537 ↗
49. Evaluation of electrical conductivity models for conductive polymer composites10.1002/app.10014 ↗
50. Deconstructing the myth of percolation in electrically conductive adhesives and its implications
51. A review of electrical conductivity models for conductive polymer composite10.1016/j.ijhydene.2016.03.045 ↗