Nonselective etching of As and P based III‒V solar cell heterostructures with aqueous solutions of HIO3 and HCl
Source abstract
Abstract
Etching characteristics of lattice-matched GaInP/GaAs/GaInNAsSb heterostructures by aqueous solutions of iodic acid (HIO3) and hydrochloric acid (HCl) is reported. The study aims at optimization of mesa fabrication process involved in the development of III‒V multijunction solar cells. The effects of temperature, agitation, etchant composition, and illumination on the etching selectivity are investigated. Varying the etchant composition and agitation rate at room temperature results in various mesa sidewall morphologies, ranging from rough surfaces and significant undercut to smoother sidewall profiles with only minor undercut. Especially, the undercut emerging in the GaInNAsSb junction, as well as in the AlInP layers, was observed for several etching conditions. Increasing the etching temperature also caused an unwanted increase in the selectivity, whereas reducing the temperature below the room temperature enhanced remarkably the formation of smooth morphology. Illumination during the etching resulted in a severe undercut in the GaAs junction, due to an increased selectivity caused by photoetching. This points out the need of controlled illumination condition to avoid unwanted reactions in wet etching of such multijunction structures. The etching process resulting in the best morphology was used for electrical isolation of triple-junction GaInP/GaAs/GaInNAsSb solar cells. The good photovoltaic performance exhibited by these devices proves the suitability of the nonselective etch process in developing multijunction solar cells.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: solar cell performance optimization · Semiconductor Quantum Structures and Devices · Chalcogenide Semiconductor Thin Films
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. Guide to references on III–V semiconductor chemical etching10.1016/S0927-796X(00)00027-9 ↗
2. Surface chemistry of prototypical bulk II−VI and III−V semiconductors and implications for chemical sensing10.1021/cr980093r ↗
3. López · 2007
4. 3-D modeling of perimeter recombination in GaAs diodes and its influence on concentrator solar cells10.1016/j.solmat.2013.08.009 ↗
5. Modelling of the perimeter recombination effect in GaAs-based micro-solar cell10.1016/j.solmat.2005.01.009 ↗
6. Does micro-scaling of CPV modules improve efficiency? A cell-to-module performance analysis10.1016/j.solener.2018.07.074 ↗
7. Analysis of perimeter recombination in the subcells of GaInP/GaAs/Ge triple‐junction solar cells10.1002/pip.2501 ↗
8. Isolation of III‒V/Ge multijunction solar cells by wet etching10.1155/2013/583867 ↗
9. Photoelectric characteristics of InGaP/Ga(In)As/Ge solar cells fabricated with a single-stage wet chemical etching separation process10.1063/1.4897088 ↗
10. Development of wet etch processing for InxAl1−xAsySb1−y solar cells grown on InP
11. Wet etching of dilute nitride GaInNAs, GaInNAsSb, and GaNAsSb alloys lattice-matched to GaAs10.1016/j.corsci.2018.03.018 ↗
12. Photovoltaic properties of low-bandgap (0.7–0.9 eV) lattice-matched GaInNAsSb solar junctions grown by molecular beam epitaxy on GaAs10.1016/j.solmat.2019.02.030 ↗
13. Nonselective wet chemical etching of GaAs and AlGaInP for device applications
14. Fidaner · 1622016
15. Composition dependent growth dynamics in molecular beam epitaxy of GaInNAs solar cells10.1016/j.solmat.2014.01.044 ↗
16. Wet etching of III‒V semiconductors
17. Baca · 2005
18. Diffusion limited chemical etching effects in semiconductors10.1016/0038-1101(94)E0072-M ↗
19. Notten · 1991
20. Estimation of activation energy and surface reaction mechanism of chlorine neutral beam etching of GaAs for nanostructure fabrication10.1088/0022-3727/47/27/275201 ↗
21. Anisotropic etching of silicon on {111} and near {111} planes
22. Franssila · 2004