journal article·2014-01

Inter-diffused ordered bulk heterojunction organic photovoltaics: optimized morphology for efficient exciton dissociation and charge transport

Buyoung Jung, Kangmin Kim, Jungwon Kim, Sehwan Kim, Eunkyoung Kim, Woochul Kim

Publisher page

Abstract

Effective control of the morphology can enhance the performance of organic photovoltaics. The morphology of an active layer needs to have a large interfacial area between donors and acceptors for efficient exciton dissociation and continuous, direct charge transport paths to electrodes for high charge transport efficiency. These two requirements are usually contradictory. Here, we propose a morphology that meets these requirements nearly simultaneously, called an inter-diffused ordered bulk heterojunction (IDOBHJ). This novel structure exhibited 9% higher performance based on the Monte Carlo simulation than an optimized disordered bulk heterojunction. The main reasons for superior performance were attributed to the comparable short circuit current density and a higher fill factor. We also implemented the IDOBHJ morphology by the experimental nanoimprint technique combined with thermal annealing process to confirm simulation results. Our experimental results are indeed consistent with the theoretical analysis.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Thin-Film Transistor Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (77)

Show source-provided references
1. On the importance of morphology control in polymer solar cells10.1002/marc.201000080 ↗
2. Polymer: fullerene bulk heterojunction solar cells10.1016/S1369-7021(11)70210-3 ↗
3. Polymer solar cells
4. Roll-to-roll fabrication of polymer solar cells10.1016/S1369-7021(12)70019-6 ↗
5. Polymer-fullerene bulk heterojunction solar cells10.1088/0034-4885/73/9/096401 ↗
6. Influence of exciton diffusion and charge-transfer state dissociation efficiency on the short-circuit current densities in semi-random donor/acceptor polymer: fullerene solar cells10.1021/jp311930m ↗
7. Photocurrent generation in polymer-fullerene bulk heterojunctions10.1103/PhysRevLett.93.216601 ↗
8. Photocurrent generation in nanostructured organic solar cells10.1021/nn700447t ↗
9. Toward high-performance polymer solar cells: the importance of morphology control10.1021/ma0618732 ↗
10. Controlling nanomorphology in plastic solar cells10.1680/nme.11.00010 ↗
11. Exciton diffusion and dissociation in a poly(p-phenylenevinylene)/C60 heterojunction photovoltaic cell10.1063/1.115797 ↗
12. Exciton diffusion and dissociation in conjugated polymer/fullerene blends and heterostructures10.1103/PhysRevB.59.15346 ↗
13. The effect of thermal treatment on the morphology and charge carrier dynamics in a polythiophene–fullerene bulk heterojunction10.1002/adfm.200400559 ↗
14. Solvent Annealing effect in polymer solar cells based on poly(3-hexylthiophene) and methanofullerenes10.1002/adfm.200600624 ↗
15. Morphology evolution via self-organization and lateral and vertical diffusion in polymer:fullerene solar cell blends10.1038/nmat2102 ↗
16. Sequential processing: control of nanomorphology in bulk heterojunction solar cells10.1021/nl202320r ↗
17. Evolution of structure, optoelectronic properties, and device performance of polythiophene: fullerene solar cells during thermal annealing10.1002/adfm.201002300 ↗
18. Materials interface engineering for solution-processed photovoltaics10.1038/nature11476 ↗
19. On modelling surface directed spinodal decomposition10.1002/mats.200500027 ↗
20. Dynamical Monte Carlo modelling of organic solar cells: the dependence of internal quantum efficiency on morphology10.1021/nl051098o ↗
21. Quantifying the relation between the morphology and performance of polymer solar cells using Monte Carlo simulations10.1063/1.2956689 ↗
22. Simulation of loss mechanisms in organic solar cells: a description of the mesoscopic Monte Carlo technique and an evaluation of the first reaction method10.1063/1.3483603 ↗
23. Dynamic Monte Carlo simulation for highly efficient polymer blend photovoltaics10.1021/jp907167u ↗
24. The quantitative effect of surface wetting layers on the performance of organic bulk heterojunction photovoltaic devices10.1021/jp2078709 ↗
25. The relative importance of domain size, domain purity and domain interfaces to the performance of bulk-heterojunction organic photovoltaics10.1039/c2ee21327c ↗
26. Morphological device model for organic bulk heterojunction solar cells10.1021/nl901511a ↗
27. Mechanism for efficient photoinduced charge separation at disordered organic heterointerfaces10.1002/adfm.201200249 ↗
28. Description of the morphology dependent charge transport and performance of polymer: fullerene bulk heterojunction solar cells10.1002/adfm.201001515 ↗
29. Morphology characterization in organic and hybrid solar cells10.1039/c2ee22056c ↗
30. Morphology of all-polymer solar cells10.1039/c2ee03071c ↗
31. Analysis of surface morphological changes in organic photovoltaic devices: bilayer versus bulk-heterojunction10.1039/c0ee00643b ↗
32. Recent advances in solution-processed interfacial materials for efficient and stable polymer solar cells10.1039/c2ee02806a ↗
33. Effects of postproduction treatment on plastic solar cells10.1002/adfm.200390011 ↗
34. Recombination in annealed and nonannealed polythiophene/fullerene solar cells: transient photovoltage studies versus numerical modeling10.1021/jz1001506 ↗
35. Improving device efficiency of polymer/fullerene bulk heterojunction solar cells through enhanced crystallinity and reduced grain boundaries induced by solvent additives10.1002/adma.201101274 ↗
36. Enhancement of P3HT/PCBM photovoltaic efficiency using the surfactant of triblock copolymer containing poly(3-hexylthiophene) and poly(4-vinyltriphenylamine) segments10.1021/ma1011182 ↗
37. Crystallization-driven enhancement in photovoltaic performance through block copolymer incorporation into P3HT: PCBM blends10.1021/ma302128h ↗
38. Fullerene crystallisation as a key driver of charge separation in polymer/fullerene bulk heterojunction solar cells10.1039/C1SC00674F ↗
39. Correlation between polymer architecture, mesoscale structure and photovoltaic performance in side-chain-modified poly(p-arylene-ethynylene)-alt-poly(p-arylene-vinylene): PCBM bulk-heterojunction solar cells10.1016/j.polymer.2011.06.008 ↗
40. Conjugated polymer photovoltaic cells10.1021/cm049654n ↗
41. Nano-confinement induced chain alignment in ordered P3HT nanostructures defined by nanoimprint lithography10.1021/nn900831m ↗
42. Hole mobility enhancement by chain alignment in nanoimprinted poly(3-hexylthiophene) nanogratings for organic electronics10.1116/1.3501343 ↗
43. A microscopic model for the behavior of nanostructured organic photovoltaic devices10.1063/1.2718865 ↗
44. Poly[3-(5-octyl-thienylene-vinyl)-thiophene]: A side-chain conjugated polymer with very broad absorption band10.1039/b516576h ↗
45. Synthesis of C60-end capped P3HT and its application for high performance of P3HT/PCBM bulk heterojunction solar cells10.1039/b923752f ↗
46. A simultaneous achievement of high performance and extended thermal stability of bulk-heterojunction polymer solar cells using a polythiophene-fullerene block copolymer10.1016/j.solmat.2012.04.035 ↗
47. Molecular miscibility of polymer−fullerene blends10.1021/jz101276h ↗
48. Bulk heterojunction photovoltaic active layers via bilayer interdiffusion10.1021/nl200552r ↗
49. Nonequilibrium behavior of thin polymer films10.1103/PhysRevE.83.021804 ↗
50. Numerical solution of initial boundary value problems involving Maxwell's equations in isotropic media10.1109/TAP.1966.1138693 ↗
51. Taflove · 1995
52. Diffusion-limited recombination in polymer-fullerene blends and its influence on photocurrent collection10.1103/PhysRevB.67.155209 ↗
53. An improved dynamic Monte Carlo model coupled with Poisson equation to simulate the performance of organic photovoltaic devices10.1063/1.3569130 ↗
54. Dynamic Monte Carlo modeling of exciton dissociation in organic donor-acceptor solar cells10.1063/1.4731698 ↗
55. A kinetic Monte Carlo model with improved charge injection model for the photocurrent characteristics of organic solar cells10.1063/1.4811337 ↗
56. Nanoimprinted P3HT/C[sub 60] solar cells optimized by oblique deposition of C[sub 60]10.1116/1.3517513 ↗
57. Formation of well-ordered heterojunctions in polymer:PCBM photovoltaic devices10.1002/adfm.201000573 ↗
58. Formation of nanopatterned polymer blends in photovoltaic devices10.1021/nl904098m ↗
59. Partial separation of fullerenes by gradient sublimation10.1021/j100141a033 ↗
60. Interdiffusion of PCBM and P3HT reveals miscibility in a photovoltaically active blend10.1002/aenm.201000023 ↗
61. Density sub-20nm SiO2 nanostructures fabricated by block copolymer template for nanoimprint lithography10.1021/nn900701p ↗
62. Organic solar cells: a new look at traditional models10.1039/c1ee01663f ↗
63. Bimolecular recombination in polymer electronic devices10.1103/PhysRevB.78.155205 ↗
64. Extracting microscopic device parameters from transient photocurrent measurements of P3HT:PCBM solar cells10.1002/aenm.201100709 ↗
65. Organic photovoltaics: challenges and opportunities10.1002/polb.23083 ↗
66. Offset energies at organic semiconductor heterojunctions and their influence on the open-circuit voltage of thin-film solar cells10.1103/PhysRevB.75.115327 ↗
67. Enhanced diode characteristics of organic solar cells using titanium suboxide electron transport layer
68. Synthesis and FT-IR spectroscopy of perdeuterofullerane: C60D36 evidences of isotope effect in the stability of C60D3610.1080/15363830903008182 ↗
69. Relating the morphology of poly(p-phenylene vinylene)/methanofullerene blends to solar-cell performance10.1002/adfm.200305049 ↗
70. A quantitative study of PCBM diffusion during annealing of P3HT: PCBM blend films10.1021/ma901444u ↗
71. Poly(3-hexylthiophene) and [6,6]-Phenyl-C61-butyric acid methyl ester mixing in organic solar cells10.1021/ma3008527 ↗
72. Poly(3-hexylthiophene): synthetic methodologies and properties in bulk heterojunction solar cells10.1039/c2ee22129b ↗
73. The effect of solvent induced crystallinity of polymer layer on poly(3-hexylthiophene)/C70 bilayer solar cells10.1016/j.solmat.2010.05.055 ↗
74. Thermally stable, efficient polymer solar cells with nanoscale control of the interpenetrating network morphology10.1002/adfm.200500211 ↗
75. Modeling nongeminate recombination in P3HT:PCBM solar cells10.1021/jp200234m ↗
76. Field effect measurements on charge carrier mobilities in various polymer-fullerene blend compositions10.1016/j.tsf.2005.12.025 ↗
77. The formation of crystalline P3HT fibrils upon annealing of a PCBM: P3HT bulk heterojunction10.1016/j.tsf.2005.12.123 ↗