journal article·2023-01Open access

Assessment of 3D micro-computed tomography for PV interconnection technology development

Rik Van Dyck, Alexandros Prapavesis, Tom Borgers, Jonathan Govaerts, Jef Poortmans, Aart W. van Vuure

Abstract

X-ray (micro-)computed tomography is a non-destructive characterization method using photons to obtain multiple radiographic projections, which generates a 3D volume rendering of a scanned object after reconstruction. It is recently used in the research and development of photovoltaic modules to investigate smaller volumes in a PV module, for example, detection of cavities in solder joints and visualization of module volumes up to connection ribbon sizes. This work shows that current advanced devices are able to scan larger volumes, using a single-cell 20 × 20 × 0.5 cm 3 module with back-contact multi-ribbon interconnection technology as an example. The generated 3D volume renderings show the interconnection structures and give information on ribbon-metallization interconnections. Next to this, also the solder reflow volume is visible, indicating that the technology has great potential to be used in further interconnection technology development. Finally, a destructive cross section analysis using scanning electron microscopy is performed; it has a higher resolution and can differentiate elements with similar photon absorption coefficients, thus enabling microstructure and intermetallic compound analysis. The findings show the potential for micro-computed tomography as a non-destructive and relatively fast visualization method and how it can give complementary information to other characterization techniques for photovoltaic interconnection research.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Integrated Circuits and Semiconductor Failure Analysis · Silicon and Solar Cell Technologies · Electron and X-Ray Spectroscopy Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Characterisation of rear local contacts including BSF formation using Raman and scanning acoustic microscopy
2. PV backsheet failure analysis by scanning acoustic microscopy
3. Nondestructive characterization of voids in rear local contacts of PERC-type solar cells10.1109/JPHOTOV.2014.2359745 ↗
4. Interconnection of silicon heterojunction solar cells by infrared soldering-solder joint analysis and temperature study
5. Scanning acoustic microscopy (SAM): a robust method for defect detection during the manufacturing process of ultrasound probes for medical imaging10.3390/s19224868 ↗
6. Scanning acoustic microscopy as a tool for quantitative characterisation of damage in CFRPs10.1016/S0266-3538(98)00086-4 ↗
7. Micromachining and validation of the scanning acoustic microscope spatial resolution and sensitivity calibration block for 20–230 MHz frequency range10.1093/jmicro/dfw027 ↗
8. Shingling technology for cell interconnection: technological aspects and process integration10.1016/j.egypro.2018.09.010 ↗
9. Multi-busbar solar cells and modules: high efficiencies and low silver consumption
10. Multi-wire interconnection of busbar-free solar cells
11. Borgers · 2016 · 3580
12. Reducing the cost of MWT module technology based on conductive back-sheet foils
13. Exploring diagnostic capabilities for application to new photovoltaic technologies
14. Non-destructive testing of crystalline silicon photovoltaic back-contact modules10.1016/j.egypro.2011.06.153 ↗
15. Microstructural characterization and unified reliability assessment of aged solder joints in a PV module10.1109/TCPMT.2020.2972027 ↗
16. Review of high energy X-ray computed tomography for non-destructive dimensional metrology of large metallic advanced manufactured components10.1088/1361-6633/ac43f6 ↗
17. Metal artifact reduction in x-ray computed tomography (CT) by constrained optimization10.1118/1.3533711 ↗
18. Quantification of metal artifacts in computed tomography: methodological considerations10.21037/qims.2020.04.03 ↗
19. Three-dimensional multi-ribbon interconnection for back-contact solar cells10.1002/pip.3390 ↗
20. Three-dimensional multi-ribbon back-contact interconnection: latest results on reliability testing
21. 2021
22. Stress and strain within photovoltaic modules using the finite element method: a critical review10.1016/j.rser.2021.111022 ↗
23. Impact of inter-metallic compound thickness on thermo-mechanical reliability of solder joints in solar cell assembly10.1016/j.microrel.2020.114008 ↗