journal article·2023-08Open access

Eddy current soldering of solar cell ribbons under a layer of glass

Dara Moazami Goodarzi, Janne Lauri, Jussi Putaala, Olli Nousiainen, Tapio Fabritius

Abstract

Thermal fatigue of soldered interconnections of silicon solar cells is considered one of the key failure modes in photovoltaic (PV) modules. Due to differences in thermal expansion coefficients of the used materials, cracks and disconnected wiring can occur, causing a local increase of resistance. This can lead to hot spots and early failure of a panel. In this research, we develop eddy current soldering as a non-contact soldering technique for tabbing the ribbon of PV cells under a layer of glass. The performance of eddy current soldering was studied in detail by changing an induction coil distance to the treated sample from 2 to 4 mm and varying exposure time. An IR camera monitored temperature profiles at the soldering zone, and I–V curves of samples were extracted to validate the soldering technique and the efficiency of the tabbing process. Electroluminescence imaging was deployed to monitor cracking after the soldering process; scanning electron microscopy (SEM) and scanning acoustic microscopy (SAM) were used to investigate the microstructure and cracking within the solder joint and silicon. The results showed that the shortest exposure times at a 2 mm heating distance caused higher risks for cracks in silicon. The intermediate exposures at a 3 mm heating distance increased the likelihood of cracking in the solder joint. For the longest heating times at a distance of 4 mm, the solder joint appeared crack free, although, in some areas, poor wetting of solder was observed. The performance of eddy current soldering under a layer of glass was compared to manually soldered samples. Based on the I–V curves, all samples were functional, and differences between exposure times and manually soldered samples were not evident. Thus, only electrical verification of the solder quality was insufficient. Due to the study, it was concluded that the proper solder interconnections through glass could be made by using the eddy current soldering process and a sufficient exposure time to avoid cracking within the solder joint configuration and silicon.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Electronic Packaging and Soldering Technologies · Integrated Circuits and Semiconductor Failure Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. Campeau · 2013
2. Review of degradation and failure phenomena in photovoltaic modules10.1016/j.rser.2022.112160 ↗
3. Crack reduction in tabbing and stringing processes for solar cells10.4028/www.scientific.net/KEM.777.126 ↗
4. Investigation of soldering for crystalline silicon solar cells, Solder10.1108/SSMT-04-2015-0015 ↗
5. Study on long term reliability of photo-voltaic modules and analysis of power degradation using accelerated aging tests and electroluminescence technique10.1016/j.egypro.2011.06.156 ↗
6. Thermal residual stress analysis of soldering and lamination processes for fabrication of crystalline silicon photovoltaic modules10.3390/en11123256 ↗
7. Detection of soldering induced damages on crystalline silicon solar modules fabricated by hot-air soldering method10.1016/j.renene.2015.05.017 ↗
8. De Rose · 2019
9. Intermetallic compounds in solar cell interconnections: microstructure and growth kinetics10.1016/j.solmat.2016.08.039 ↗
10. Study on the effect of soldering methods on the characteristics of the Ni-Cr alloy10.4047/jkap.2012.50.1.53 ↗
11. A study on soldering characteristics of laser tabbing system for crystalline silicon photovoltaic module production10.1007/s12206-014-0739-5 ↗
12. Lead-free solders for ribbon interconnection of crystalline silicon PERC solar cells with infrared soldering10.1063/1.5125880 ↗
13. Growth kinetics of Ag3Sn in silicon solar cells with a sintered Ag metallization layer10.1016/j.solmat.2014.01.018 ↗
14. Field failure mechanism study of solder interconnection for crystalline silicon photovoltaic module10.1016/j.microrel.2012.06.027 ↗
15. The effects of temperature and solders on the wettability between ribbon and solar cell10.1016/j.solmat.2008.10.005 ↗
16. Non-contact characterization of flexible hybrid electronics by synchronized thermography10.1109/TIM.2019.2962576 ↗
17. Sizing up the efficiency of induction heating systems for soldering electronic modules10.3103/S1068375518040105 ↗
18. Properties of Sn-Ag-Cu solder joints prepared by induction heating10.1155/2020/1724095 ↗
19. Photographic diagnosis of crystalline silicon solar cells utilizing electroluminescence10.1007/s00339-008-4986-0 ↗
20. Characterization of flip chip interconnect failure modes using high frequency acoustic micro imaging with correlative analysis
21. Finite-difference simulation of Eddy currents in nonmagnetic sheets via electric vector potential10.1109/TMAG.2019.2940204 ↗
22. Interaction of an Eddy-Current coil with a right-angled conductive wedge10.1109/TMAG.2009.2036724 ↗
23. Shear strengths and fracture behaviors of Cu/Sn37Pb/Cu soldered joints subjected to different displacement rates10.1016/j.jallcom.2014.02.039 ↗
24. Effect of Co addition into Ni film on shear strength of solder/Ni/Cu system: experimental and theoretical investigations10.1016/j.msea.2020.139589 ↗
25. Influence of thermal cycling-induced failures on RF performance of ceramic antenna assemblies10.1109/TCPMT.2011.2110655 ↗