journal article·2011-06

Engineering of hybrid interfaces in organic photovoltaic devices

Konstantinos Fostiropoulos, Marin Rusu

Publisher page

Abstract

Abstract In this study, we engineer and investigate the interface structure and chemistry at the indium tin oxide (ITO) anode (front-side electrode) as well as at the Mg−Ag cathode (back-side electrode) in metal phthalocyanine (MePc)/C60 organic solar cells (OSCs). For the front-side electrode, Zn-phthalocyaninetetraphosphonic acid (Zn-PTPA) and Sn-phthalocyanine axially substituted with tartaric acid (Sn-PTA) have been used for the surface termination of ITO coated glass substrates. Both terminations yielded OSCs with higher fill factors and open circuit voltages, thus increasing the power conversion efficiency by 33% and 67%, respectively. A possible influence of a chemisorbed Zn-PTPA on the film growth of the adjacent ZnPc absorber in the vicinity of the hybrid interface is discussed using X-ray reflectivity and near edge X-ray absorption fine structure data. Distinct effects of the Zn-PTPA and Sn-PTA terminations on the electronic properties of the ITO surface were found by X-ray photoelectron spectroscopy (XPS) measurements at the valence band edge. We demonstrate the possibility to engineer the hybrid interface without additional buffer. For the back-side electrode we report the formation of buffer-free charge carrier selective Mg−Ag cathodes, which are applied for bulk heterojunction organic absorbers consisting of copper phthalocyanine (CuPc) donor and fullerene C60 acceptor materials. The chemical and structural properties of the CuPc:C60/Mg−Ag interface are investigated by element depth profiling using secondary ion mass spectrometry (SIMS), grazing incidence X-ray diffraction analysis (GI-XRD) and XPS. We demonstrate that an optimum charge carrier selectivity is achieved with Mg:Ag/Ag cathode structures, where the Mg:Ag alloy layer has a composition close to that of Ag3Mg. In addition, Mg diffusion into CuPc:C60 layer is observed. As a result, an interaction between Mg and Cu2+ with a concurrent change in oxidation state of both metals takes place. However, no formation of MgPc is observed. The findings of this work are discussed against the background of the performance and electrical properties of the corresponding MePc/C60-based organic solar cells.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Advanced Memory and Neural Computing

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Preparation and investigation of phthalocyanine/C60 solar cells
2. 2008
3. Monolayer passivation of the transparent electrode in organic solar cells10.1016/j.tsf.2005.04.058 ↗
4. M. Rusu, B. Johnev, F. Streicher, N. Barreau, M. Vogel, Th. Glatzel, S. Sadewasser M.Ch. Lux-Steiner, K. Fostiropoulos, Work function homogeneity of monolayer passivated ITO surfaces for organic solar cells, Conference record of the 89th OSA Annual Meeting: Frontiers in Optics 2005, Laser Science XXI, October 18–19, Tucson, USA, 2005, ISBN 1-55752-797-0, p.SMA3.10.1364/FIO.2005.SMA3 ↗
5. Zinc-phthalocyaninetetraphosphonic acid as a novel transparent-conducting-oxide passivation for organic photovoltaic devices10.1016/j.solmat.2007.09.014 ↗
6. Fabrication of electron injecting Mg:Ag alloy electrodes for organic light-emitting diodes with radio frequency magnetron sputter deposition10.1063/1.117047 ↗
7. Improvement in power efficiency in organic light emitting diodes through intermediate Mg:Ag layer in LiF/Mg:Ag/Al cathodes10.1149/1.2756337 ↗
8. Top light-harvesting organic solar cell using ultrathin Ag/MgAg layer as anode10.1143/JJAP.46.1734 ↗
9. Low work function MgAg-coated poly(ethylene terephthalate) films for organic light-emitting device fabrication with lamination process10.1143/JJAP.46.7483 ↗
10. Moffat · 1984
11. Work function measurements on indium tin oxide films10.1016/S0368-2048(01)00310-3 ↗
12. Toward accurate in-depth profiling of As and P ultra-shallow implants by SIMS10.1016/j.apsusc.2004.03.130 ↗
13. Latest developments for the CAMECA ULE-SIMS instruments: IMS Wf and SC-Ultra10.1016/j.apsusc.2004.03.202 ↗
14. On the SIMS depth profiling analysis: reduction of matrix effect10.1016/0168-1176(94)04113-L ↗
15. Niesen, Synchrotron-based soft X-ray spectroscopy
16. Organic donor, acceptor and buffer layers of small molecules prepared by OVPD technique for photovoltaics10.1016/j.renene.2007.05.021 ↗
17. Organic p-i-n solar cells10.1007/s00339-003-2494-9 ↗
18. Characterization of zinc phthalocyanine (ZnPc) for photovoltaic applications10.1007/s00339-003-2184-7 ↗
19. Surface studies of solids by total reflection of X-rays10.1103/PhysRev.95.359 ↗
20. Molecular orientation of F16ZnPc deposited on Au and Mg substrates studied by NEXAFS and IRRAS10.1016/j.cplett.2005.07.083 ↗
21. Electronic structure and current injection in zinc phthalocyanine doped with tetrafluorotetracyanoquinodimethane: interface versus bulk effects10.1016/S1566-1199(02)00033-2 ↗
22. Formation of charge-selective Mg–Ag electrodes to CuPc:C60 blend layers10.1063/1.3481395 ↗
23. Chemical bonding and electronic structures at magnesium/copper phthalocyanine interfaces10.1016/j.apsusc.2005.09.027 ↗