Large area, high efficiency and stable perovskite solar cells enabled by fine control of intermediate phase
Source abstract
Abstract
Abstract Organic-inorganic lead halide perovskites have shown great potential in efficient photovoltaic devices. However, there are issues related to device stability and reliability and the high power conversion efficiencies (PCE) are typically demonstrated on cell areas much less than 0.2 cm2. The main challenges which limit high efficiencies in larger area devices lie on the low temperature solution processing methods which typically produce lower quality perovskites with defects (pinholes and traps) and the undesired increase in series resistance with cell area. Herein, the control of the dimethyl sulfoxide (DMSO) adduct intermediate phase for the formation of the defect-free perovskite layer and their suitability for larger area solar cells are investigated. We have also selected different conducting substrates, namely indium tin oxide (ITO) with sheet resistance of 10 Ω/□ and fluorine doped tin oxide (FTO) substrates with sheet resistances of 7 and 15 Ω/□ to characterize the effect of substrate sheet resistance and transparency on the photovoltaic performance in large area devices. We demonstrate high PCEs of 18.2% for small area devices (0.16 cm2) and 15.1% for large area device (2 cm2) using the DMSO-enriched recipe. In addition, enhanced device stability was observed, where the devices sustained 94% of their initial efficiency after 105 days without encapsulation. These results confirm that the fine control of adduct intermediate phase for reduced-defect perovskite film provides a simple and universal solution for larger area, efficient and stable perovskite solar cells.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Perovskite Materials and Applications · Conducting polymers and applications · Chalcogenide Semiconductor Thin Films
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Organometal halide perovskites as visible-light sensitizers for photovoltaic cells10.1021/ja809598r ↗
2. 6.5% efficient perovskite quantum-dot-sensitized solar cell10.1039/c1nr10867k ↗
3. Chemical management for colorful, efficient, and stable inorganic–organic hybrid nanostructured solar cells10.1021/nl400349b ↗
4. Efficient hybrid solar cells based on meso-superstructured organometal halide perovskites10.1126/science.1228604 ↗
5. Hollow rice grain-shaped TiO2 nanostructures for high-efficiency and large-area perovskite solar cells10.1016/j.solmat.2018.11.028 ↗
6. High-performance photovoltaic perovskite layers fabricated through intramolecular exchange10.1126/science.aaa9272 ↗
7. Compositional engineering of perovskite materials for high-performance solar cells10.1038/nature14133 ↗
8. Towards high efficiency thin film solar cells10.1016/j.pmatsci.2017.02.003 ↗
9. Performance enhancement of tri‐cation and dual‐Anion mixed perovskite solar cells by Au@ SiO2 nanoparticles10.1002/adfm.201606545 ↗
10. High efficiency planar-type perovskite solar cells with negligible hysteresis using EDTA-complexed SnO210.1038/s41467-018-05760-x ↗
11. Planar-structure perovskite solar cells with efficiency beyond 21%10.1002/adma.201703852 ↗
12. Enhanced photovoltage for inverted planar heterojunction perovskite solar cells10.1126/science.aap9282 ↗
13. Impact of monovalent cation halide additives on the structural and optoelectronic properties of CH3NH3PbI3 perovskite10.1002/aenm.201502472 ↗
14. Employing lead thiocyanate additive to reduce the hysteresis and boost the fill factor of planar perovskite solar cells10.1002/adma.201600594 ↗
15. Enhanced photovoltaic performance of perovskite solar cells using polymer P(VDF-TrFE) as a processed additive10.1021/acs.jpcc.6b05255 ↗
16. Thermally stable MAPbI3 perovskite solar cells with efficiency of 19.19% and area over 1 cm2 achieved by additive engineering10.1002/adma.201701073 ↗
17. Ionic liquid control crystal growth to enhance planar perovskite solar cells efficiency10.1002/aenm.201600767 ↗
18. Ionic liquid-Assisted perovskite crystal film growth for high performance planar heterojunction perovskite solar cells10.1039/C6RA24616H ↗
19. Additive enhanced crystallization of solution‐processed perovskite for highly efficient planar‐heterojunction solar cells10.1002/adma.201400231 ↗
20. One-step, low-temperature deposited perovskite solar cell utilizing small molecule additive10.1117/1.JPE.5.057405 ↗
21. Balancing transformation and dissolution–crystallization for pure phase CH3NH3PbI3 growth and its effect on photovoltaic performance in planar-structure perovskite solar cells10.1016/j.solmat.2018.05.062 ↗
22. A promising unisource thermal evaporation for in situ fabrication of organolead halide perovskite CH3NH3PbI3 thin film10.1002/pip.2632 ↗
23. High-performance perovskite CH 3 NH 3 PbI 3 thin films for solar cells prepared by single-source physical vapour deposition10.1038/srep29910 ↗
24. Highly uniform large-area (100 cm2) perovskite CH3NH3PbI3 thin-films prepared by single-source thermal evaporation10.3390/coatings8080256 ↗
25. Vacuum flash–Assisted solution process for high-efficiency large-area perovskite solar cells10.1126/science.aaf8060 ↗
26. A pure and stable intermediate phase is key to growing Aligned and vertically monolithic perovskite crystals for efficient PIN planar perovskite solar cells with high processibility and stability10.1016/j.nanoen.2017.02.019 ↗
27. Efficient and Ambient‐Air‐stable solar cell with highly oriented 2D@ 3D perovskites10.1002/adfm.201801654 ↗
28. Lewis Acid–base adduct Approach for high efficiency perovskite solar cells10.1021/acs.accounts.5b00440 ↗
29. Highly reproducible perovskite solar cells with average efficiency of 18.3% and best efficiency of 19.7% fabricated via lewis base adduct of lead (II) iodide10.1021/jacs.5b04930 ↗
30. Solvent engineering for high-performance inorganic–organic hybrid perovskite solar cells10.1038/nmat4014 ↗
31. Temperature effect of the compact TiO2 layer in planar perovskite solar cells: an interfacial electrical, optical and carrier mobility study10.1016/j.solmat.2017.01.005 ↗
32. Dimensional engineering of a graded 3D–2D halide perovskite interface enables ultrahigh Voc enhanced stability in the p‐i‐n photovoltaics10.1002/aenm.201701038 ↗
33. Iodide management in formamidinium-lead-halide–based perovskite layers for efficient solar cells10.1126/science.aan2301 ↗
34. A fast deposition-crystallization procedure for highly efficient lead iodide perovskite thin‐film solar cells10.1002/ange.201405334 ↗
35. Universal Approach toward hysteresis-free perovskite solar cell via defect engineering10.1021/jacs.7b10430 ↗
36. Enhanced charge carrier transport and device performance through dual-cesium doping in mixed-cation perovskite solar cells with near unity free carrier ratios10.1021/acsami.6b12845 ↗
37. Enhanced thermal stability in perovskite solar cells by Assembling 2d/3d stacking structures10.1021/acs.jpclett.7b02679 ↗
38. Ultrafast photogenerated hole extraction/transport behavior in a CH3NH3PbI3/carbon nanocomposite and its Application in a metal‐electrode‐free solar cell10.1002/cphc.201600817 ↗
39. Photocarrier recombination dynamics in perovskite CH3NH3PbI3 for solar cell Applications10.1021/ja506624n ↗
40. Improved Air stability of perovskite solar cells via solution-processed metal oxide transport layers10.1038/nnano.2015.230 ↗
41. Intensity dependence of current voltage characteristics and recombination in high-efficiency solution-processed small-molecule solar cells10.1021/nn401267s ↗
42. Interpretation and evolution of open-circuit voltage, recombination, ideality factor and subgap defect states during reversible light-soaking and irreversible degradation of perovskite solar cells10.1039/C7EE02415K ↗
43. Leong · Adv. Mater. · 2016 · 28 · 243910.1002/adma.201505480 ↗
44. Causes and solutions of recombination in perovskite solar cells
45. Meaning of reaction orders in polymer: fullerene solar cells10.1103/PhysRevB.86.165201 ↗
46. Relationship between energetic disorder and open-circuit voltage in bulk heterojunction organic solar cells10.1103/PhysRevB.84.075210 ↗
47. Enhanced efficiency parameters of solution‐processable small‐molecule solar cells depending on ITO sheet resistance10.1002/aenm.201300277 ↗
48. Photovoltaic property dependence of dye-sensitized solar cells on sheet resistance of FTO substrate deposited via spray pyrolysis10.1016/j.ceramint.2012.01.018 ↗
49. FTO/ITO double-layered transparent conductive oxide for dye-sensitized solar cells10.1016/j.jphotochem.2003.12.028 ↗
50. Fully printable organic and perovskite solar cells with transfer-printed flexible electrodes10.1021/acsami.7b02717 ↗
51. Flexible counter electrodes based on metal sheet and polymer film for dye-sensitized solar cells10.1016/j.tsf.2004.07.083 ↗
52. Post-treatment of perovskite film with phenylalkylammonium iodide for hysteresis-less perovskite solar cells10.1016/j.solmat.2018.02.015 ↗
53. Performance improvement of perovskite solar cells by employing a CdSe quantum dot/PCBM composite as an electron transport layer10.1039/C7TA00203C ↗
54. RF sputtered CdS films as independent or buffered electron transport layer for efficient planar perovskite solar cell10.1016/j.solmat.2018.01.017 ↗