journal article·2016-12

Influence of minimum position in [Ga]/([Ga]+[In]) profile of Cu(In,Ga)Se2 on flexible stainless steel substrate on its photovoltaic performances

Jakapan Chantana, Taichi Watanabe, Seiki Teraji, Takashi Minemoto

Publisher page

Abstract

Abstract Cu(In, Ga)Se 2 (CIGS) solar cells on stainless steel (SUS) substrates are fabricated with various [Ga]/([Ga]+[In]), GGI, profiles in their absorbers. From GGI profiles, near-surface GGI is defined as average GGI within 200 nm from CIGS surface, mini GGI value is the lowest GGI, and mini GGI position is a distance between the lowest GGI position and CIGS surface. These are used as representatives of the GGI profile. Their impacts on cell performances are quantitatively examined. It is revealed that near-surface GGI is optimized in a range of approximately 0.40–0.45 (or band-gap energy of 1.28–1.30 eV), resulting in improvement of conduction band offset at CdS/CIGS interface. From simulation, optimized mini GGI position is in a range of 250–350 nm, well consistent with space charge region width. According to experimental results, fill factor and open-circuit voltage are increased when mini GGI position is decreased from 1.1 to 0.4 µm, while short-circuit current density is increased with decreasing mini GGI value. Ultimately, 17.3%-efficient CIGS solar cell on flexible SUS substrate with thin CIGS thickness of 1.5 µm is achieved, where near-surface GGI, mini GGI position, and mini GGI value are 0.42, 0.5 µm, and 0.06, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · ZnO doping and properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Background and motivation for thin-film solar-cell development
2. Epitaxial thin film crystalline silicon solar cells on low cost silicon carriers
3. Properties of Cu(In,Ga)Se2 solar cells with new record efficiencies up to 21.7%10.1002/pssr.201409520 ↗
4. Potassium-induced surface modification of Cu(In,Ga)Se2 thin films for high-efficiency solar cells10.1038/nmat3789 ↗
5. Highly efficient Cu(In,Ga)Se2 solar cells grown on flexible polymer films10.1038/nmat3122 ↗
6. Electronic properties of Cu(In,Ga)Se2 solar cells on stainless steel foil without diffusion barrier10.1002/pip.1247 ↗
7. Flexible Cu(In,Ga)Se2 solar cell on stainless steel substrate deposited by multi-layer precursor method: its photovoltaic performance and deep-level defects10.1002/pip.2748 ↗
8. Impact of Ga/(In+Ga) profile in Cu(In,Ga)Se2 prepared by multi-layer precursor method on its cell performance10.1016/j.tsf.2014.01.009 ↗
9. Investigation of Cu(In,Ga)Se2 absorber by time-resolved photoluminescence for improvement of its photovoltaic performance10.1016/j.solmat.2014.08.012 ↗
10. Controlled back slope of Ga/(In+Ga) profile in Cu(In,Ga)Se2 absorber fabricated by multi layer precursor method for improvement of its photovoltaic performance10.1016/j.solmat.2014.11.023 ↗
11. Physical properties of Cu(In,Ga)Se2 film on flexible stainless steel substrate for solar cell application: a multi-layer precursor method10.1016/j.solmat.2015.08.001 ↗
12. Chantana · 2015
13. Band-gap engineering in Cu(In,Ga)Se2 thin films grown from (In,Ga)2Se3 precursors10.1016/0927-0248(95)00122-0 ↗
14. A. Chirila, D. Guettler, P. Bloesch, S. Nishiwaki, S. Seyrling, S. Buecheler, R. Verma, F. Pianezzi, Y.E. Romanyuk, G. Bilger, R. Ziltener, D. Bremaud, A.N. Tiwari, Optimization of composition grading in Cu(In,Ga)Se2 for flexible solar cells and modules, in: Conference Proceedings of the 35th IEEE Photovoltaic Specialists Conference, 2010, pp. 656–660.10.1109/PVSC.2010.5616887 ↗
15. Band-gap grading in Cu(In,Ga)Se2 solar cells
16. Modelling polycrystalline semiconductor solar cells10.1016/S0040-6090(99)00825-1 ↗
17. Influence of iron on defect concentrations and device performance for Cu(In,Ga)Se2 solar cells on stainless steel substrates10.1002/pip.2260 ↗
18. CIGS thin-film solar cells on steel substrates10.1016/j.tsf.2008.11.016 ↗
19. Enhancing efficiency of Cu(In,Ga)Se2 solar cells on flexible stainless steel foils using NaF co-evaporation10.1016/j.solener.2013.03.010 ↗
20. Dielectric barriers for flexible CIGS solar modules10.1016/S0040-6090(01)01516-4 ↗
21. Barrier effect of AlN film in flexible Cu(In,Ga)Se2 solar cells on stainless steel foil and solar cell10.1016/j.jallcom.2014.12.021 ↗
22. Electronic properties of Cu(In,Ga)Se2heterojunction solar cells-recent achievements, current understanding, and future challenges10.1007/s003390050984 ↗
23. Effect of Cu deficiency on the optical bowing of chalcopyrite Cu In1−x GaxSe210.1063/1.2089154 ↗
24. Dielectric function of Cu(In, Ga)Se2-based polycrystalline materials10.1063/1.4790174 ↗
25. Investigation of compositional inhomogeneities in complex polycrystalline Cu(In,Ga)Se2 layers for solar cells10.1063/1.3280049 ↗
26. Characterization of Cu(InGa)Se2 (CIGS) thin films in solar cell devices by secondary ion mass spectrometry10.1384/jsa.17.324 ↗
27. Surface characterization of chemically treated Cu(In, Ga)Se2 thin films10.1143/JJAP.35.4760 ↗
28. Influence of KCN treatment on CuInS2 thin films10.1016/0169-4332(95)00236-7 ↗
29. Interdependence of absorber composition and recombination mechanism in Cu(In,Ga)(Se,S)2 heterojunction solar cells10.1063/1.1467621 ↗
30. Thin-film solar cells: Device measurements and analysis10.1002/pip.518 ↗
31. Bhattacharya · 1994
32. Infrared Faraday effect in n-type CuInSe210.1002/pssb.2220810161 ↗
33. Thermal properties of p-type CuInSe210.1002/pssa.2210590268 ↗
34. Theoretical analysis of the effect of conduction band offset of window/CIS layers on performance of CIS solar cells using device simulation10.1016/S0927-0248(00)00266-X ↗
35. The recombination parameter J010.1016/j.egypro.2014.08.073 ↗
36. Influence of conduction band minimum difference between transparent conductive oxide and absorber on photovoltaic performance of thin-film solar cell