journal article·2009-01

Network structure organic photovoltaic devices prepared by electrochemical copolymerization

So Yeon Kim, Kwang Hee Lee, Byung Doo Chin, Jae-Woong Yu

Publisher page

Abstract

Characteristics of the organic photovoltaic devices prepared by in-situ electrochemical copolymerization of substituted fullerene with alkylthiophene were studied. The active layer was formed by direct electrochemical copolymerization between thiophene moiety substituted fullerene and 3-octylthiophene on PEDOT-coated indium tin oxide (ITO) glass, where fullerene is anchored within conducting polymer chain through covalent bonding. Since two monomers utilized in this study had an opposite oxidation potential, the step potential bias method was used to copolymerize these two monomers. Bias potential and concentration of monomers were carefully controlled so that blend ratio of composite film was exactly same as monomer feed. Power conversion efficiency of electrochemically copolymerized photovoltaic device changed within experimental error ranges for before and after heat treatment. Meanwhile, composite films prepared by spin coating of blend of poly(3-octylthiophene) and PCBM showed morphological changes after heat treatment at 8 °C for 1 h according to field emission scanning electron microscopy (FE-SEM) study. This study suggests a new approach for preventing migration of fullerene from its optimized morphology.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Semiconductor materials and interfaces

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. Two-layer organic photovoltaic cell10.1063/1.96937 ↗
2. The limits to organic photovoltaic cell efficiency10.1557/mrs2005.5 ↗
3. Semiconducting polymer–buckminsterfullerene heterojunctions: diodes, photodiodes and photovoltaic cells10.1063/1.108863 ↗
4. Efficient photodiodes from interpenetrating polymer networks10.1038/376498a0 ↗
5. 2.5% efficient organic plastic solar cells10.1063/1.1345834 ↗
6. Effects of postproduction treatment on plastic solar cells10.1002/adfm.200390011 ↗
7. Thermally stable, efficient polymer solar cells with nanoscale control of the interpenetrating network morphology10.1002/adfm.200500211 ↗
8. Efficient tandem polymer solar cells fabricated by all-solution processing10.1126/science.1141711 ↗
9. How to model the behavior of organic photovoltaic cells10.1002/pi.2038 ↗
10. Conjugated polymer-based organic solar cells10.1021/cr050149z ↗
11. Low band gap polymers for organic photovoltaics10.1016/j.solmat.2007.01.015 ↗
12. Polymer–fullerene composite solar cells10.1002/anie.200702506 ↗
13. Dual-function semiconducting polymer devices: light-emitting and photodetecting diodes10.1063/1.111885 ↗
14. Temperature dependence for the photovoltaic device parameters of polymer–fullerene solar cells under operating conditions10.1063/1.1412270 ↗
15. Determination of the degradation constant of bulk heterojunction solar cells by accelerated lifetime measurements10.1007/s00339-003-2499-4 ↗
16. Flexible organic P3HT:PCBM bulk-heterojunction modules with more than 1 year outdoor lifetime10.1016/j.solmat.2008.01.004 ↗
17. A setup for studying stability and degradation of polymer solar cells10.1016/j.solmat.2008.02.008 ↗
18. Flexible, conjugated polymer–fullerene-based bulk-heterojunction solar cells: basics, encapsulation and integration10.1557/jmr.2005.0399 ↗
19. Nanoscale morphology of high-performance polymer solar cells10.1021/nl048120i ↗
20. Analysis of the failure mechanism for a stable organic photovoltaic during 10,000h of testing10.1002/pip.794 ↗
21. Stability/degradation of polymer solar cells10.1016/j.solmat.2008.01.005 ↗
22. Creation of a gradient polymer–fullerene interface in photovoltaic devices by thermally controlled interdiffusion10.1063/1.1522830 ↗
23. A route to stable nanostructures in conjugated polymers10.1021/ma0714823 ↗
24. Bulk heterojunctions based on native polythiophene10.1021/cm800431s ↗
25. A fulleropyrrolidine end-capped platinum-acetylide triad: the mechanism of photoinduced charge transfer in organometallic photovoltaic cells10.1039/b700379j ↗
26. Tetrafullerene conjugates for all-organic photovoltaics10.1021/jo702740d ↗
27. Electronic transport properties aspects and structure of polymer–fullerene based organic semiconductor for photovoltaic devices10.1016/j.tsf.2005.12.029 ↗
28. Polymers containing fullerene or carbon nanotube structures10.1016/j.progpolymsci.2004.08.001 ↗
29. Undoping effect of electropolymerized polymer for two-layer organic photovoltaic cells based on polymer/dye junction10.1002/app.1993.070481214 ↗
30. Photovoltaic devices based on polythiophenes and substituted polythiophenes10.1016/S0379-6779(00)00575-0 ↗
31. Interpenetrating organic conducting polymer composites based on polyaniline and poly(3,4-ethylenedioxythiophene) from sequential electropolymerization10.1016/j.jelechem.2005.05.015 ↗
32. Electrical properties of porous silicon/polypyrrole heterojunction10.1016/j.solmat.2006.03.014 ↗
33. Novel poly(3-methylthiophene)–TiO2 hybrid materials for photovoltaic cells10.1016/j.tsf.2005.12.112 ↗
34. Poly(3,4-ethylenedioxythiophene)-semiconductor nanoparticle composite thin films tethered to indium tin oxide substrates via electropolymerization10.1021/ja073332d ↗
35. Hybrid copper–indium disulfide/polypyrrole photovoltaic structures prepared by electrodeposition10.1016/j.solmat.2004.07.023 ↗
36. Fabrication of solid-state dye-sensitized TiO2 solar cells combined with polypyrrole10.1016/S0927-0248(98)00052-X ↗
37. A photoelectrochemical solar cell based on ZnO/dye/polypryyolr film electrode as photoanode10.1016/S0927-0248(99)00077-X ↗