journal article·2022-09Open access

Demonstration of molded glass primary optics for high-efficiency micro-concentrator photovoltaics

Norman Jost, Guido Vallerotto, Alessandro Tripoli, Steve Askins, César Domínguez, Ignacio Antón

Abstract

Micro-concentrator photovoltaics (micro-CPV) is a branch of the CPV technology where the size of the solar cell is reduced below the millimeter range to permit novel manufacturing methods for cost reductions and maintaining high efficiencies by using high performance optical materials. The reduction in size of all the components demands a very good optical quality of the primary lenses to achieve high concentrations and high optical efficiencies. PMMA or silicon-on-glass are the most used materials for CPV primary optics, but PMMA reliability against UV weathering is questionable and silicone has a large coefficient of thermal expansion (CTE) mismatch with respect to glass, which introduces a large thermal sensitivity in the optical efficiency. In contrast, direct glass molding is a promising alternative due to benefits such as a high Abbe number (lower dispersion losses), great mechanical properties, low CTE, low thermal coefficient of the refractive index (dn/dT), and a proven outdoor reliability with very little degradation. Furthermore, glass can generally be manufactured with high throughput, straightforward, and cost-effective compression or roller molding processes. In this work we present a collaboration with the company Holophane S.A.S. in France that resulted in the manufacturing of several micro-CPV lens arrays of plano-convex lenses with a design tailored to the requirements imposed by the manual compression molding process. A comprehensive experimental characterization has been carried out based on surface metrology and functional measurements with a collimated-light solar simulator, and the results are compared with ray-tracing simulations. The measured optical efficiency at the design concentration of 178X is 79.2 ± 2.5% for the whole array with a best lens efficiency of 82.2%. Furthermore, the best performing array has been used to assemble a demonstrator mono-module, which has been characterized outdoors. The outdoor characterization shows very good thermal and spectral stability of the lens array with an I–V curve fill factor of 84.8 ± 1.9% and an electrical efficiency of 27.2 ± 1.8%. The experience gained with these prototypes will lead to further optimization in the manufacturing process to increase the optical performance, and to a larger scale manufacturing for micro-CPV modules. This works paves the way for the development of high-efficiency robust glass-based micro-CPV modules able to generate maximum energy yield per area in space-constrained applications.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: solar cell performance optimization · Chalcogenide Semiconductor Thin Films · TiO2 Photocatalysis and Solar Cells

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Domínguez · 2017
2. Precision glass molding: toward an optimal fabrication of optical lenses10.1007/s11465-017-0408-3 ↗
3. Comparative analysis of different secondary optical elements for aspheric primary lenses10.1364/OE.17.006487 ↗
4. Patton Edward · 2007
5. Design and demonstration of ultra-compact microcell concentrating photovoltaics for space10.1364/OE.27.0A1467 ↗
6. Ultra-compact high flux tailored edge-ray space micro concentrators
7. The CPV “Toolbox”: new approaches to maximizing solar resource utilization with application-oriented concentrator photovoltaics10.3390/en14040795 ↗
8. Industrialization of hybrid Si/III–V and translucent planar micro-tracking modules
9. Durability of Fresnel lenses: a review specific to the concentrating photovoltaic application10.1016/j.solmat.2011.01.031 ↗
10. A micro-concentrator photovoltaic module incorporating a bifacial silicon solar cell for direct and diffuse light capture
11. Fabrication of a double-sided micro-lens array by a glass molding technique10.1088/0960-1317/21/8/085020 ↗
12. Indoor experimental assessment of the efficiency and irradiance spot of the achromatic doublet on glass (ADG) fresnel lens for concentrating photovoltaics
13. Solar simulator for concentrator photovoltaic systems10.1364/OE.16.014894 ↗
14. Impact of the temperature dependence of CPV optics transmittance on the current mismatch of multi-junction solar cells10.1063/1.5053534 ↗
15. The path to volume production for CPV optics
16. Injection molding of high-precision optical lenses: a review10.1016/j.precisioneng.2022.02.002 ↗
17. Datasheet
18. Challenges in the design of concentrator photovoltaic (CPV) modules to achieve highest efficiencies10.1063/1.5046752 ↗
19. Bäumer · 2013
20. Review on fabrication technologies for optical mold inserts10.3390/mi10040233 ↗
21. Nelson · 2020
22. Bäumer · 2011
23. Schaub · 2013
24. Overview of PV module encapsulation materials
25. SAV Helios · 2021 · 3198
26. Assessment of the optical efficiency of a primary lens to be used in a CPV system10.1016/j.solener.2016.05.016 ↗
27. Current-matching estimation for multijunction cells within a CPV module by means of component cells10.1002/pip.2227 ↗
28. IES-UPM Meteo Data Repository
29. Kyu Kim · 2019
30. Efficient mold manufacturing for precision glass molding
31. Investigation of different Fresnel lens designs and methods to determine the optical efficiency10.1063/1.4897037 ↗
32. Direct comparison of polymethylmetacrylate (PMMA) and silicone-on-glass (SOG) for Fresnel lenses in concentrating photovoltaics (CPV)10.1117/12.893884 ↗
33. Optics for concentrating photovoltaics: Trends, limits and opportunities for materials and design10.1016/j.rser.2016.01.089 ↗
34. Challenges in the design of concentrator photovoltaic (CPV) modules to achieve highest efficiencies10.1063/1.5046752 ↗
35. 43 % sunlight to electricity conversion efficiency using CPV10.1109/JPHOTOV.2016.2551460 ↗
36. Vallerotto · 2019