journal article·2017-08Open access

An end of service life assessment of PMMA lenses from veteran concentrator photovoltaic systems

David C. Miller, Hussameldin I. Khonkar, Rebeca Herrero, Ignacio Antón, David K. Johnson, Thorsten Hornung, Tobias Schmid-Schirling, Todd B. Vinzant, Steve Deutch, Bobby To, Gabriel Sala, Sarah R. Kurtz

Abstract

The optical performance of poly(methyl methacrylate) lenses from veteran concentrator photovoltaic modules was examined after the end of their service life. Lenses from the Martin-Marietta and Intersol module designs were examined from the “Solar Village” site near Riyadh, Saudi Arabia, as well as the Phoenix Sky Harbor airport, followed by the Arizona Public Service Solar Test and Research (APS-STaR) center in Tempe, Arizona. The various lens specimens were deployed for 20, 27, and 22 years, respectively. Optical characterizations included lens efficiency (Solar Simulator instrument), material transmittance and haze (of coupons cut from veteran lenses, then measured again after their faceted back surface was polished, and then measured again after the incident front surface was polished), and direct transmittance (as a function of detector's acceptance angle, using the Very Low Angular Beam Spread (“VLABS”) instrument). Lens efficiency measurements compared the central region to the entire lens, also using hot and cold mirror measurements to diagnose differences in performance. A series of subsequent characterizations was performed because a decrease in performance of greater than 10% was observed for some of the veteran lenses. The optimal focal distance of the lenses was quantified using the Solar Simulator, and then correlated to lens curvature using a recently developed measurement technique. Surface roughness was examined using atomic force microscopy and scanning electron microscopy. Facet geometry (tip and valley radius) was quantified on cross-sectioned specimens. Molecular weight was compared between the incident and faceted surfaces of the lenses.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: solar cell performance optimization · Photovoltaic System Optimization Techniques · Surface Roughness and Optical Measurements

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (100+)

Show source-provided references
1. 2003 · 449
2. Durability of Fresnel lenses: a review specific to the concentrating photovoltaic application10.1016/j.solmat.2011.01.031 ↗
3. Analysis of transmitted optical spectrum enabling accelerated testing of multi-junction CPV designs10.1117/1.3530092 ↗
4. F. Ruesch, S. Brunold, Ageing performance of collector glazing materials–results from 20 years of outdoor weathering, in: Proceedings of the EuroSun Conference, 2008.
5. Durability of poly(methyl methacrylate) lenses used in concentrating photovoltaics
6. H. Gomez, G.S. Kinsey, A. Nayak, H. Oba, CPV reliability program at AMONIX Inc., in: Proceedings of the International Conference CPV, 2011, pp. 327–330.
7. Solar radiation durability framework applied to acrylic solar mirrors
8. Reliability
9. Durability of poly(methyl methacrylate) lenses used in concentrating photovoltaics
10. D.C. Miller, T. Arndt, R. Kogler, Characteristics of a veteran acrylic lens relative to acrylic lens materials after accelerated laboratory weathering, in: Proceedings of the 11th International Conference on Concentrator Photovoltaic Systems (Aix-les-Bains, France), 2015.10.1063/1.4931503 ↗
11. M.O. Nazer, Photovoltaic concentrator power station for a village in Saudi Arabia, in: Proceedings of the Euro PVSEC, 1980, pp. 368–374.10.1007/978-94-009-8423-3_53 ↗
12. Solar energy in Saudi Arabia: the SolERAS project
13. F.S. Huraib, B.H. Khoshaim, A. Al-Sani, M.S. Imamura, A.A. Salim, Design installation and initial performance of 350-kW photovoltaic power system for Saudi Arabian villages, in: Proceedings of the Euro PVSEC, 1982, pp. 57–66.10.1007/978-94-009-7898-0_9 ↗
14. F.S. Huraib, A. Al-Sani, B.H. Khoshaim, Operational results from the Saudi solar village photovoltaic power system, in: Proceedings of the IEEE IECEC, 1982, pp. 1531–1534.
15. B.H. Khoshaim, F.S. Huraib, A. Al-Sani, A.A. Salim, Eighteen-month performance of 350kW PVPS for Saudi Arabian villages, in: Proceedings of the IEEE IECEC, 1983, pp. 1278–1283.
16. B.H. Khoshaim, F.S. Huraib, A. Al-Sani, A.A. Salim, Performance of 350kW concentrating photovoltaic power system after two years, in: Proceedings of the Euro PVSEC, 1983, pp. 207–214.
17. B.H. Khoshaim, F.S. Huraib, A. Al-Sani, A.A. Salim, M.S. Imamura, Performance of 350kW photovoltaic power system for Saudi Arabian villages after 30 months, in: Proceedings of the IEEE PVSC, 1984, pp. 1426–1432.
18. A. Bowen, S.A. Balto, A. Al-Saief, Photovoltaic electrification of 3 villages in Saudi Arabia, in: Proceedings of the PLEA Conference, 1985, pp. 837–848.10.1016/B978-0-08-031644-4.50067-9 ↗
19. A.A. Salim, F.S. Huraib, B.H. Khoshaim, N.N. Eugenio, N.R. Rao, Four year performance summary of 350kW concentrating photovoltaic power system, in: Proceedings of the IEEE PVSC, 1985, pp. 1545–1552.
20. A.A. Salim, F.S. Huraib, B.H. Khoshaim, N.N. Eugenio, N.R. Rao, M.S. Imamura, Performance characteristics of the 350kW concentrator photovoltaic array field, in: Proceedings of the IEEE IECEC, 1986, pp. 1285–1291.
21. F.S. Huraib, A.A. Salim, The first interconnection of a solar photovoltaic power system with the utility grid in Saudi Arabia, in: Proceedings of the Symp. Electr. Power Fast Develop. Countries, 1987, pp. 512–515.
22. A.A. Salim, F.S. Huraib, N.N. Eugenio, T.C. Lepley, Performance comparison of two similar concentrating PV systems operating in the U.S. and Saudi Arabia, in: Proceedings of the IEEE PVSC, 1987, pp. 1351–1357.
23. A comprehensive report on the performance of the longest operating 350kW concentrator photovoltaic power system
24. M.S. Smiai, S. Al-Awaji, Performance of a 350kW photovoltaic concentrator field (in operation since 1981), in: Proceedings of the Euro. PVSEC, 1992, pp. 1340–1343.
25. Evaluation of solar energy research and its applications in Saudi Arabia – 20 years of experience10.1016/S1364-0321(00)00006-X ↗
26. Photovoltaic Concentrator Technology Development Project: First Project Integration Meeting, SAND-78-0374, 1978, pp. 1–151.
27. R.L. Donovan, S. Broadbent, 10-kW Photovoltaic Concentrator Array, SAND78-7024, 1978, pp. 1–194.
28. Photovoltaic Concentrator Technology Development Project: Second Project Integration Meeting, SAND-78-0988, 1978, pp. 1–227.
29. Photovoltaic Concentrator Technology Development Project: Third Project Integration Meeting, SAND-79-0557, 1979, pp. 1–141.
30. Photovoltaic Concentrator Technology Development Project: Fourth Project Integration Meeting, SAND-79-1791, 1979, pp. 1–347.
31. Photovoltaic Concentrator Technology Development Project: Fifth Project Integration Meeting, SAND-80-0852, 1980, pp. 1–337.
32. Photovoltaic Concentrator Technology Development Project: Sixth Project Integration Meeting, SAND-80-2373, 1980, pp. 1–298.
33. J.A. Sanders, R.L. Donovan, S. Broadbent, 10-kW Photovoltaic Concentrator Fabrication, SAND80-7062, 1980, pp. 1–294.
34. N. Sharma, Airport Solar Photovoltaic Concentrator Project, DOE-CS-05317-1, 1979, pp. 1–335.
35. W.J. McGuirk, Solar photovoltaic concentrator project at Sky Harbor airport, in: Proceedings of the ASME ASPCP Conference, 1982, pp. 1–6.
36. W.J. McGuirk, Phase II Fabrication and Construction of the Sky Harbor Airport Solar Photovoltaic Concentrator Project, DOE-ET-20624-1, 1984, pp. 1–60.
37. Photovoltaics generation – recent technology advancements
38. T. Lepley, Sky Habor Photovoltaic Concentrator Project, Phase III: First Forty-two Months of Operation, DOE-ET-20624-T14, 1986, pp. 1–83.
39. Past experience and new challenges of PV concentrators
40. S. Boradbent, J.E. Baumann, B.W. Heler, D.J. Hughs, L.S. Marshall, R.P. Semma, R.E. Stegeman, Second Generation Photovoltaic Concentrator Array Design, SAND82-7133, 1982, pp. 1–321.10.2172/6567483 ↗
41. J.A. Sanders, Design of Photovoltaic Central Power Station Concentrator Array, SAND82-7148, 1982, pp. 1–255.
42. S. Broadbent, J.A. Sanders, Development and Fabrication of Photovoltaic Concentrator Modules for a Point-Focus Fresnel Lens Array, SAND85-7001, 1985, pp. 1–76.
43. An investigation of the changes in poly(methyl methacrylate) specimens after exposure to ultra-violet, heat, and humidity10.1016/j.solmat.2012.05.043 ↗
44. D.C. Miller, H.I. Khonkar, R. Herrero, I. Antón, D.K. Johnson, T. Hornung, T. Schmid, T.B. Vinzant, B. To, G. Sala, S.R. Kurtz, An End of Service Life Assessment of PMMA Lenses from Veteran Concentrator Photovoltaic Systems, NREL-PR-5J00-67733, 2017.10.1016/j.solmat.2017.03.031 ↗
45. Effects of sorbed water on crack propagation in poly(methyl methacrylate) under static tensile stress10.1023/A:1004803030131 ↗
46. Craze growth in PMMA under cyclic loads10.1002/app.1973.070170401 ↗
47. Interferenzoptische vermessung der craze-zone vor der rißspitze in PMMA unterschiedlichen molekulargewichtes10.1007/BF01517034 ↗
48. The kinetics of the growth of “silver” cracks in transparent solid polymers
49. Mechanism of fracture in glassy polymers: I. Fracture surfaces of polymethyl methacrylate
50. Mechanism of fracture in glassy polymers. III: direct observation of the craze ahead of the propagating crack in poly(methyl methacrylate) and polystyrene10.1002/pol.1966.160040305 ↗
51. Craze shape and fracture in poly(methyl methacrylate)10.1016/0032-3861(73)90152-3 ↗
52. Crazing under applied compression
53. Residual craze and crack formation in poly(methyl methacrylate)10.1002/pen.760230409 ↗
54. Time-dependent deformation and craze initiation in PMMA: volume effects10.1016/0032-3861(84)90165-4 ↗
55. Strain-amplitude and strain-rate dependent craze damage of poly(methyl methacrylate)
56. Yield criteria for plastic deformation of glassy high polymers in general stress fields
57. Yielding of glassy polymers in the second quadrant of principal stress space10.1080/00222347308201636 ↗
58. Solvent stress crazing in PMMA: 1. Geometrical effects10.1016/0032-3861(74)90160-8 ↗
59. Craze initiation in poly(methyl methacrylate) under biaxial stress
60. Effect of water on the crazing of a crosslinked poly(methyl methacrylate)10.1007/BF00724868 ↗
61. Size and mechanical properties of craze zones at propagating crack tips in poly(methyl methacrylate) during fatigue loading10.1016/0032-3861(83)90256-2 ↗
62. Non-steady periodic behavior in the dynamic fracture of PMMA10.1007/BF00012390 ↗
63. Nonsteady crack and craze behavior in PMMA under cyclical loading: I. Experimental preliminaries10.1023/A:1007577904159 ↗
64. Nonsteady crack and craze behavior in PMMA under cyclical loading: II. Effect of load history on growth rate and fracture morphology10.1023/A:1007525920089 ↗
65. Nonsteady crack and craze behavior in PMMA under cyclical loading: III. Effect of load history on cohesive force distribution on the craze10.1023/A:1007569703250 ↗
66. Craze growth in polymethylmethacrylate: a fracture mechanics approach
67. On the environmental fracture of polymethylmethacrylate10.1007/BF00823210 ↗
68. Environmental crazing and intrinsic tensile deformation in polymethylmethacrylate10.1007/BF00540922 ↗
69. The influence of liquid environmental media on the mechanical behavior of thermoplastics10.1002/pi.4980100113 ↗
70. Effect of absorbed water on the thermal relaxation of biaxially stretched crosslinked poly(methyl methacrylate)10.1016/0032-3861(79)90202-7 ↗
71. The fracture of acrylic polymer sin water10.1007/BF00550261 ↗
72. Effects of sorbed water on properties of low and high molecular weight PMMA: 1. Deformation and fracture behavior10.1016/0032-3861(85)90150-8 ↗
73. Sorbed water and mechanical behavior of poly(methyl methacrylate)
74. Environmental crazing and cracking in poly(methyl methacrylate) under diametral compression10.1007/BF03372201 ↗
75. Influence of water on crack propagation in poly methyl methacrylate: craze stress and craze fibril lifetime10.1007/BF00351609 ↗
76. Effects of humidity on creep fracture and crazing behavior of PMMA
77. The effects of diffusion on environmental; stress crack initiation in PMMA10.1023/A:1004431920449 ↗
78. Effects of humidity on environmental stress cracking behavior in poly(methyl methacrylate)10.1002/polb.10045 ↗
79. Environmental fatigue testing of molded plastics for prothetic heart valves10.1007/BF02326566 ↗
80. Fatigue crack propagation of PMMA in organic solvents
81. Effects of sorbed water on properties of low and high molecular weight PMMA: 11. Fatigue performance10.1016/0032-3861(85)90061-8 ↗
82. Fracture surface energy and craze fibril stress in PMMA in water
83. Time-temperature-stress superposition principle of PMMA's crazing damages under creep condition10.1007/s11771-007-0273-z ↗
84. Spannungsrissverhalten von PMMA nach freibewittrung10.1002/apmc.1983.051140115 ↗
85. Altstädt · 2005 · 126
86. Polymethyl methacrylate plus water: sorption kinetics and volumetric changes10.1016/0032-3861(82)90300-7 ↗
87. Durability of polymeric encapsulation materials for concentrating photovoltaic systems10.1002/pip.1241 ↗
88. Solar simulator for concentrator photovoltaic systems10.1364/OE.16.014894 ↗
89. Effects of temperature on hybrid lens performance10.1063/1.3658294 ↗
90. Advances in indoor characterization of CPV modules and components
91. Methodology of quantifying curvature of Fresnel lenses and its effect on CPV module performance10.1364/OE.23.0A1030 ↗
92. IEC 60904-3: Photovoltaic devices, Part 3: Measurement Principles for Terrestrial Photovoltaic (PV) Solar Devices with Reference Spectral Irradiance Data, International Electrotechnical Commission: Geneva, 2016, (188 pages).
93. Assessment of the optical efficiency of a primary lens to be used in a CPV system10.1016/j.solener.2016.05.016 ↗
94. IEC 62788-1-4: Measurement Procedures for Materials Used in Photovoltaic Modules – Part 1–4: Encapsulants – Measurement of Optical Transmittance and Calculation of the Solar-Weighted Photon Transmittance, Yellowness Index, and UV Cut-off Frequency, International Electrotechnical Commission: Geneva, 2016, (37 pages).
95. Examination of an optical transmittance test for photovoltaic encapsulation materials
96. D.C. Miller, J. Apezteguia, J.G. Bokria, M. Köhl, N.E. Powell, M.E. Smith, M.D. White, H.R. Wilson, J.H. Wohlgemuth, Examination of an Optical Transmittance Test for Photovoltaic Encapsulation Materials, NREL/PR-5200-60379, 2013, pp. 1–24.
97. A. Heimsath, T. Schmid, P. Nitz, Angle resolved specular reflectance measured with VLABS, in: Proceedings of the International Conference Concentrating Solar Power Chem. Energy Syst. (SolarPACES 2014), Energy Procedia, 69, 2015, pp. 1895–1903, http://dx.doi.org/10.1016/j.egypro.2015.03.173.10.1016/j.egypro.2015.03.173 ↗
98. Leutz · 2001
99. Durability of polymeric encapsulation materials in a PMMA/glass concentrator photovoltaic system10.1002/pip.2796 ↗
100. Scalar scattering theory for multilayer optical coatings10.1117/12.7972335 ↗