Enhanced thermal stability of organic photovoltaics via incorporating triphenylamine derivatives as additives
Source abstract
Abstract
Abstract In this work, we prepared four star-shaped conjugated small molecules, the triphenylamine dithiophene (TBT) derivatives, namely TBT-H, TBT-Br, TBT-OH, and TBT-N 3 presenting hydride, bromide, hydroxyl, and azide terminal functional groups, respectively. These TBT derivatives were used as additives in the active layers of organic photovoltaics to investigate the effect of intermolecular interactions (TBT-H, TBT-OH) or crosslinking (TBT-N 3 , TBT-Br) on the long-term thermal stability of the devices. From analyses of blend film morphologies, and optoelectronic and device performance, we observed significant enhancements in thermal stability during accelerated heating tests at 150 °C for the devices incorporated with the additives TBT-N 3 and TBT-Br. These two additives functioned as crosslinkers, and constructed local borders that effectively impeded heat-promoted fullerene aggregation, thereby leading to highly stable morphologies. When compared with corresponding normal devices, the TBT-N 3 –derived devices based on poly(3-hexylthiophene) exhibited greater stability, with the power conversion efficiency (PCE) remaining as high as 2.5% after 144h at 150 °C. Because of this enhancement, a device based on an amorphous low-bandgap polymer, namely poly(thieno[3,4- b ]thiophene- alt -benzodithiophene), with the addition of TBT-N 3 was fabricated. We observed a significant improvement in device stability, retaining approximately 60% (from 5.0 to 3.3%) of its initial PCE under accelerated heating (150 °C). In contrast, the PCE of the corresponding normal device decayed to 0.01% of its initial value.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Thin-Film Transistor Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (49)
Show source-provided references
1. Polymer–fullerene bulk-heterojunction solar cells10.1002/adma.200903697 ↗
2. Interface investigation and engineering – achieving high performance polymer photovoltaic devices10.1039/b925382c ↗
3. Printable luminescent down shifter for enhancing efficiency and stability of organic photovoltaics10.1016/j.solmat.2015.09.037 ↗
4. Making ends meet: flow synthesis as the answer to reproducible high-performance conjugated polymers on the scale that roll-to-roll processing demands10.1002/aenm.201401996 ↗
5. Probing individual subcells of fully printed and coated polymer tandem solar cells using multichromatic opto-electronic characterization methods10.1016/j.solmat.2015.01.030 ↗
6. A polymer tandem solar cell with 10.6% power conversion efficiency10.1038/ncomms2411 ↗
7. 25th Anniversary Article: Bulk heterojunction solar cells: understanding the mechanism of operation10.1002/adma.201304373 ↗
8. Single junction inverted polymer solar cell reaching power conversion efficiency 10.31% by employing dual-doped zinc oxide nano-film as cathode interlayer10.1038/srep06813 ↗
9. Aggregation and morphology control enables multiple cases of high-efficiency polymer solar cells10.1038/ncomms6293 ↗
10. Single-junction polymer solar cells exceeding 10% power conversion efficiency10.1002/adma.201404535 ↗
11. A series of simple oligomer-like small molecules based on oligothiophenes for solution-processed solar cells with high efficiency10.1021/jacs.5b00305 ↗
12. From lab to fab: how must the polymer solar cell materials design change? – an industrial perspective10.1039/c3ee43460e ↗
13. Stability of polymer solar cells10.1002/adma.201104187 ↗
14. Large scale deployment of polymer solar cells on land, on sea and in the air10.1039/c3ee43212b ↗
15. Solution processed large area fabrication of Ag patterns as electrodes for flexible heaters, electrochromics and organic solar cells10.1039/c4ta00301b ↗
16. High-efficiency solution processable polymer photovoltaic cells by self-organization of polymer blends10.1038/nmat1500 ↗
17. Spatial Fourier-Transform analysis of the morphology of bulk heterojunction materials used in “Plastic” solar cells10.1002/adma.200601933 ↗
18. Conjugated polymer photovoltaic cells10.1021/cm049654n ↗
19. A quantitative correlation between the mobility and crystallinity of photo-cross-linkable P3HT10.1021/ma202203z ↗
20. Thermally stable bulk heterojunction solar cells based on cross-linkable acrylate-functionalized polythiophene diblock copolymers10.1021/ma3020905 ↗
21. Stabilization of the film morphology in polymer: Fullerene heterojunction solar cells with photocrosslinkable bromine-functionalized low-bandgap copolymers10.1002/pola.26695 ↗
22. Solvent-resistant organic transistors and thermally stable organic photovoltaics based on cross-linkable conjugated polymers10.1021/cm203058p ↗
23. Photo-cross-linkable azide-functionalized polythiophene for thermally stable bulk heterojunction solar cells10.1021/ma3001725 ↗
24. Morphological stabilization by in situ polymerization of fullerene derivatives leading to efficient, thermally stable organic photovoltaics10.1002/adfm.201002502 ↗
25. Cross-linkable azido C60-fullerene derivatives for efficient thermal stabilization of polymer bulk-heterojunction solar cells10.1039/C4TC01178C ↗
26. Highly thermal stable and efficient organic photovoltaic cells with crosslinked networks appending open-cage fullerenes as additives10.1002/adfm.201401735 ↗
27. Stabilization of poly(3-hexylthiophene)/PCBM morphology by hydroxyl group end-functionalized P3HT and its application to polymer solar cells10.1016/j.orgel.2011.11.019 ↗
28. Manipulating the horizontal morphology and vertical distribution of the active layer in BHJ-PSC with a multi-functional solid organic additive10.1039/C3TA15378A ↗
29. Improved thermal stability of polymer solar cells by incorporating porphyrins10.1002/adfm.201403018 ↗
30. Thermal stabilisation of polymer–fullerene bulk heterojunction morphology for efficient photovoltaic solar cells10.1002/adma.201401062 ↗
31. A solvent additive to enhance the efficiency and the thermal stability of polymer:fullerene solar cells10.1039/C4RA14139C ↗
32. Dual function additives: a small molecule crosslinker for enhanced efficiency and stability in organic solar cells10.1002/aenm.201401426 ↗
33. Enhanced efficiency of organic and perovskite photovoltaics from shape-dependent broadband plasmonic effects of silver nanoplates10.1016/j.solmat.2015.04.021 ↗
34. Electron spin resonance of tropenyl radical110.1021/ja01093a059 ↗
35. Thermal stabilisation of polymer-fullerene bulk heterojunction morphology for efficient photovoltaic solar cells10.1002/adma.201401062 ↗
36. Increasing the open-circuit voltage in high-performance organic photovoltaic devices through conformational twisting of an indacenodithiophene-based conjugated polymer10.1002/marc.201300569 ↗
37. Morphology of polymer/fullerene bulk heterojunction solar cells10.1039/B510618B ↗
38. Applications of functional fullerene materials in polymer solar cells10.1039/c3ee43080d ↗
39. Nanoscale morphology of high-performance polymer solar cells10.1021/nl048120i ↗
40. Efficient polymer solar cells based on a low bandgap semi-crystalline dpp polymer-PCBM blends10.1002/adma.201200902 ↗
41. Synthesis of conjugated polymers bearing indacenodithiophene and cyclometalated platinum(II) units and their application in organic photovoltaics10.1016/j.solmat.2012.09.033 ↗
42. Organic photovoltaics incorporating fulleroisoquinolinones as n-type materials10.1039/C0CC04246C ↗
43. Low-bandgap poly(thiophene-phenylene-thiophene) derivatives with broaden absorption spectra for use in high-performance bulk-heterojunction polymer solar cells10.1021/ja801877k ↗
44. For the bright future—bulk heterojunction polymer solar cells with power conversion efficiency of 7.4%10.1002/adma.200903528 ↗
45. Recent advances in bulk heterojunction polymer solar cells10.1021/acs.chemrev.5b00098 ↗
46. When function follows form: effects of donor copolymer side chains on film morphology and BHJ solar cell performance10.1002/adma.201002687 ↗
47. Correlating high power conversion efficiency of PTB7:PC71BM inverted organic solar cells with nanoscale structures10.1039/C5NR03332B ↗
48. Organic photovoltaics: crosslinking for optimal morphology and stability10.1016/j.mattod.2015.04.001 ↗
49. Morphological stabilization by supramolecular perfluorophenyl-C60 interactions leading to efficient and thermally stable organic photovoltaics10.1002/adfm.201300437 ↗