journal article·2024-10

TiO2/Se heterojunction photovoltaic device made from Se/Te/Se stacked precursor

Taizo Kobayashi, Takumi Miyamoto, Ryota Ogata, Zacharie Jehl Li-Kao

Publisher page

Abstract

This paper presents an innovative approach for forming crystallized selenium (c-Se) using a Se/Te/Se stacked precursor. The aim is to enhance the adhesion between the TiO2 and Se layers to improve the power conversion efficiency of TiO2/Se heterojunction photovoltaic devices. Our previous study revealed that the accumulation of Te near the TiO2/Se interface resulted in insufficient shunt resistance, leading to increased dark leakage current. This issue arises because Te possesses a high carrier density (similar to 10(18) cm(-3)) and narrow bandgap energy (0.26 eV). However, a Te additive layer remains necessary to passivate the unbonded TiO2/Se interface and to maximize the adhesion between the absorber and the substrate. Previous research on Se-based photovoltaic devices demonstrated that an extremely thin (similar to 0.5 nm) and homogeneous Te adhesion layer could be formed beneath the Se photo-absorbing layer and subsequently crystallized through air-annealing post-deposition. However, achieving precise and homogeneous sub-nanometer Te films using a compact resistance heating evaporation system in a laboratory setting proved challenging so far. To address these limitations, we propose a novel technique for forming the Se absorber layer by post-annealing a stacked 1st-Se/Te/2nd-Se precursor on a TiO2 window layer. Through experimentation, we achieved the highest power conversion efficiency of 4.49 % without antireflective coating, accompanied by V-oc 0.795V, J(SC) 11.13 mA/cm(2), and FF 0.507 when the 1st-Se thickness was 5 nm. Furthermore, the impact of decreasing Te/(Te + Se) near the TiO2 window layer on photovoltaic performance was theoretically predicted using modelling by SCAPS-1D. Overall, this work introduces a promising method for enhancing the formation of c-Se, improving adhesion between TiO2 and Se layers, and enhancing the power conversion efficiency of TiO2/Se heterojunction photovoltaic devices.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Phase-change materials and chalcogenides

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. On the fritss selenium cells and batteries10.1016/0016-0032(85)90426-0 ↗
2. Properties of piezoelectric selenium and selenium layers10.1080/00150198208008111 ↗
3. Thermoelectric power and mobility of carriers in selenium10.1103/PhysRev.77.734 ↗
4. Polycrystalline thin-film TiO 2/Se solar cells10.1143/JJAP.24.L536 ↗
5. Ultrathin high band gap solar cells with improved efficiencies from the world's oldest photovoltaic material10.1038/s41467-017-00582-9 ↗
6. Record efficiencies for selenium photovoltaics and application to indoor solar cells
7. Ordering one-dimensional chains enables efficient selenium photovoltaics
8. Maximum efficiencies of indoor photovoltaic devices10.1109/JPHOTOV.2012.2225023 ↗
9. Selenium thin-film solar cells with cadmium sulfide as a heterojunction partner10.1021/acsaem.1c01700 ↗
10. Monolithic selenium/silicon tandem solar cells10.1103/PRXEnergy.3.013013 ↗
11. Materials perspectives for next-generation low-cost tandem solar cells10.1016/j.solmat.2017.07.033 ↗
12. Modern processing and insights on selenium solar cells: the world's first photovoltaic device10.1002/aenm.201802766 ↗
13. Origin of photovoltaic losses in selenium solar cells with open-circuit voltages approaching 1 V10.1039/D2TA07729A ↗
14. Indoor photovoltaics awaken the world’s first solar cells10.1126/sciadv.adc9923 ↗
15. Photovoltaic performances of TiO2/Se heterojunction devices with different crystallographic structures of sputter-deposited TiO2 thin films10.1016/j.matchemphys.2023.127371 ↗
16. Impact of piezo-phototronic effect on ZnMgO/Se heterojunction photovoltaic devices10.1016/j.nanoen.2022.107385 ↗
17. Formation of micro‐patterned Ga 2 O 3/Se heterojunction and its application to highly sensitive avalanche photodiode
18. Acceleration of wettability switching on TiO2 thin films under ultraviolet irradiation and direct current bias voltage10.1016/j.surfcoat.2019.02.043 ↗
19. TiO 2 patterns with wide photo-induced wettability change by a combination of reactive sputtering process and surface modification in a microfluidic channel10.1088/0960-1317/25/11/115014 ↗
20. Low-voltage-operation avalanche photodiode based on n-gallium oxide/p-crystalline selenium heterojunction10.1063/1.4883649 ↗
21. Modelling polycrystalline semiconductor solar cells10.1016/S0040-6090(99)00825-1 ↗
22. Advanced electrical simulation of thin film solar cells10.1016/j.tsf.2012.10.032 ↗
23. Numerical modeling of intra-band tunneling for heterojunction solar cells in scaps10.1016/j.tsf.2006.12.049 ↗
24. Germanium-Gallium arsenide heterojunctions10.1147/rd.43.0283 ↗
25. Design of lead-free perovskite solar cell using Zn1-Mg O as ETL: SCAPS device simulation10.1016/j.ijleo.2021.167306 ↗
26. Te/CdTe and Al/CdTe interfacial energy band alignment by atomistic modeling10.1021/acsami.2c05244 ↗
27. Nonlinear band gap tunability in selenium–tellurium alloys and its utilization in solar cells10.1021/acsenergylett.9b01619 ↗
28. Fabrication and characterization of ZnO/Se1-xTex solar cells10.1007/s12200-022-00040-5 ↗
29. Theoretical analysis of the effect of conduction band offset of window/CIS layers on performance of CIS solar cells using device simulation10.1016/S0927-0248(00)00266-X ↗
30. Cu(In,Ga)Se 2 solar cells with controlled conduction band offset of window/Cu(In,Ga)Se2 layers10.1063/1.1366655 ↗
31. Cu(In,Ga)Se2 thin film solar cells with a combined ALD-Zn(O,S) buffer and MOCVD-ZnO:B window layers10.1016/j.solmat.2013.05.052 ↗