journal article·2024-10

Improving n-TOPCon solar cell printing conditions and performance analysis by local dot contact approaches

Hasnain Yousuf, Muhammad Quddamah Khokhar, Alamgeer, Rafi ur Rahman, Polgampola Chamani Madara, Jaljalalul Abedin Jony, Maha Nur Aida, Muhammad Aleem Zahid, Donghyun Oh, Youngkuk Kim, Junsin Yi

Publisher page

Abstract

This study investigates the optimization of printing conditions for n-TOPCon (n-type Tunnel Oxide Passivated Contact) solar cells to enhance their efficiency and performance. Key parameters varied include, dot print type, co-firing belt speed, and paste application method. Experiments conducted on n-type Cz silicon wafers analyzed the impact of high-temperature TOPCon Ag paste and low-temperature HIT (Heterojunction with Intrinsic Thin layer) paste on cell performance. The highest efficiency of 22.57 % was achieved at a belt speed of 100 ipm (inch per minute) with the incorporation of low-temperature HIT paste in a single dot printing configuration. Similarly, at 130 ipm, an efficiency of 22.15 % was obtained under optimized conditions. The fill factor (FF) significantly improved, achieving an FF of 79.66 % at 100 ipm and 78.63 % at 130 ipm. The optimal belt speed of 130 ipm was found to offer the best compromise between enhancing cell efficiency and minimizing potential thermal damage. The best short-circuit current density (J sc) of 41.70 mA/cm 2 was achieved at 100 ipm, while the highest open-circuit voltage (Voc) of 0.69007 V was recorded at 130 ipm. Loss analysis indicated that efficiency and FF improvements were primarily driven by superior passivation and reduced contact resistance. This comprehensive study underscores the critical role of optimizing printing conditions to enhance n-TOPCon solar cell efficiency, contributing to more efficient and cost-effective photovoltaic technologies.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Thin-Film Transistor Technologies · solar cell performance optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. High-efficiency crystalline silicon solar cells: status and perspectives10.1039/C5EE03380B ↗
2. Phosphorus-diffused polysilicon contacts for solar cells10.1016/j.solmat.2015.06.001 ↗
3. n-Type Si solar cells with passivating electron contact: identifying sources for efficiency limitations by wafer thickness and resistivity variation10.1016/j.solmat.2017.05.042 ↗
4. Solar cell efficiency tables (Version 45)10.1002/pip.2573 ↗
5. High-efficiency silicon heterojunction solar cells: a review10.1515/green-2011-0018 ↗
6. Passivated rear contacts for high-efficiency n-type Si solar cells providing high interface passivation quality and excellent transport characteristics10.1016/j.solmat.2013.09.017 ↗
7. Influence of Ag-paste properties on the performance of screen-printed front side metallizations for silicon solar cells
8. Impact of silver paste properties on the contact formation and performance of silicon heterojunction solar cells
9. Crystalline silicon solar cells—state of the art and future developments
10. Electronic properties of light‐induced recombination centers in boron‐doped Czochralski silicon10.1063/1.371186 ↗
11. Schropp · 1998
12. Silicon heterojunction solar cells with screen-printed metallization exceeding 22% efficiency
13. The effect of annealing on the properties of amorphous silicon oxide passivation layers for silicon heterojunction solar cells
14. Transport and recombination in silicon heterojunction solar cells
15. Current status and challenges for hole-selective poly-silicon based passivating contacts10.1063/5.0185379 ↗
16. Laser-doped, contact-passivated rear for industrial p-type Si solar cells
17. Silicon heterojunction solar cells: recent advances and outlook
18. Silver screen-printing pastes for silicon solar cells: material requirements for high efficiency solar cells and a simple model for describing the serial resistance of the metal layer
19. Improving the efficiency of silicon solar cells by using selective emitters formed by laser doping
20. Metal aerosol jet printing for solar cell metallization10.1002/pip.759 ↗
21. High-efficiency p-type silicon solar cell with an a-Si: H/c-Si heterojunction emitter and an a-Si: H/TiO2 passivation layer
22. Advanced screen printed polymer Ag paste for HIT cells
23. Surface passivation of crystalline silicon solar cells: present and future10.1016/j.solmat.2018.06.047 ↗
24. Low-temperature processes for passivation and metallization of high-efficiency crystalline silicon solar cells10.1016/j.solener.2018.01.074 ↗
25. Improving surface passivation on very thin substrates for high efficiency silicon heterojunction solar cells10.1016/j.solmat.2020.110715 ↗
26. Efficient carrier-selective p-and n-contacts for Si solar cells10.1016/j.solmat.2014.05.039 ↗
27. Role of firing temperature, sheet resistance, and contact area in contact formation on screen-printed metal contact of silicon solar cell10.1007/s11664-017-6022-7 ↗
28. Characterization of screen printed and fire-through contacts on LPCVD based passivating contacts in monoPolyTM solar cells10.1016/j.solener.2020.03.087 ↗