Collimated solar simulator for curved PV modules characterization
Source abstract
Abstract
The vehicle integrated photovoltaic (VIPV) technology, which consists in integrating PV solar panels in the surfaces of electric vehicles, is a promising technology to increase car autonomy. Free-form curved PV surfaces are demanded to meet the specific design constraints of the automotive. The proper characterization of three dimensional PV surfaces requires specific methods and equipment that must be developed. This paper describes the design principles and requirements of a solar simulator for characterization of curved PV modules. Its effectiveness is demonstrated by means of ray-tracing simulations, the results show the advantages provided by the use of a collimated light source in comparison to the conventional solar simulators used for flat modules. The light beam divergence of a non-collimated light source produces a non-uniformity boost between 2% and 20% depending on the module size and curvature. The module performance will be affected by this non-uniform irradiance, but the performance loss will also depend on specific characteristics of the module such as curvature, number and size of cells, series/parallel electrical connection and number of by-pass diodes. On the contrary, the proposed collimated solar simulator reproduces the solar illumination profile over the curved surface. The Helios 3198, a solar simulator with collimated light developed for concentrator modules, has been adapted accordingly to the design proposed. A module of 1 m of curvature has been tested, the short-circuit current of the cells follows the ideal cosine response of the curvature, differences are lower than 0.5% which proves the quality of the collimated beam.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: solar cell performance optimization · Photovoltaic System Optimization Techniques · Solar Thermal and Photovoltaic Systems
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. 2022
2. Static concentrator photovoltaics for automotive applications10.1016/j.solener.2017.03.028 ↗
3. NEDO, “Interim Report from ‘PV-Powered Vehicle Strategy Committee.’”.
4. International Standard Series · 2022
5. CPV standardization 2021 – maintenance and stability
6. “IEC 60904-9 Ed3. Photovoltaic devices – Part 9: solar simulator characteristics.”
7. LED-based solar simulator for terrestrial solar spectra and orientations10.1016/j.solener.2022.01.001 ↗
8. Determining the accuracy of solar cell and module measurements on high-capacitance devices
9. Importance of developing high-efficiency solar cells for PV-powered vehicles
10. Development of high‐efficiency and low‐cost solar cells for PV‐powered vehicles application10.1002/pip.3343 ↗
11. Challenges in the design of concentrator photovoltaic (CPV) modules to achieve highest efficiencies10.1063/1.5046752 ↗
12. Current-matching estimation for multijunction cells within a CPV module by means of component cells: current-matching estimation for MJ cells within a concentrator10.1002/pip.2227 ↗
13. Determination of spectral variations by means of component cells useful for CPV rating and design: determination of spectral variations10.1002/pip.2715 ↗
14. Characterization of CPV modules and receivers
15. Characterization of five CPV module technologies with the Helios 3198 solar simulator
16. IEC 62670-3 Photovoltaic concentrators (CPV) - performance testing - Part 3: performance measurements and power rating
17. Droz · 2010
18. Curve correction of the energy yield by flexible photovoltaics for VIPV and BIPV applications using a simple correction factor
19. Curve correction of vehicle‐integrated photovoltaics using statistics on commercial car bodies
20. Solar simulator for concentrator photovoltaic systems10.1364/OE.16.014894 ↗
21. Solar simulator for indoor characterization of large area high-concentration PV modules
22. Characterization capabilities of solar simulators for concentrator photovoltaic modules10.7567/JJAP.51.10ND12 ↗
23. Indoor characterization of CPV modules using the Helios 3198 solar simulator
24. Realization of a solar simulator for production testing of HCPV modules
25. Experimental analysis and simulation of a production line for CPV modules: impact of defects, misalignments, and binning of receivers10.1002/ese3.178 ↗
26. On the effect of cell interconnection in Vehicle Integrated Photovoltaics: modelling energy under different scenarios
27. Evaluation of the solar resource and energy generation in vehicle integrated photovoltaics
28. Freniere · 1981 · 19
29. Fest · 2013
30. Masoumi · 2012
31. Calculation of the PV modules angular losses under field conditions by means of an analytical model10.1016/S0927-0248(00)00408-6 ↗
32. 2013
33. Constant voltage I–V curve flash tester for solar cells10.1016/j.solmat.2003.11.001 ↗
34. Sinton · 2006