Achieving an efficient Sb2Se3-based solar cell by improving the performance parameters using the grey wolf optimization algorithm
Source abstract
Abstract
Antimony selenide (Sb 2Se 3 ) exhibits promising characteristics as an absorber material in photovoltaic solar cells. To enhance the efficiency of Sb 2Se 3 solar cells, we propose a reevaluation of the device design through the utilization of device simulation techniques and optimization algorithms. To ensure the model`s accuracy, a calibration procedure is performed by comparing the experimental data obtained from a fabricated structure (Mo/MoSe 2/Sb 2Se 3/TiO 2 /CdS/ZnO/Al:ZnO) with numerical simulation results. Simultaneous investigation was conducted to assess the efficacy of incorporating sulfur into the absorber layer of Sb 2Se 3 and introducing zinc into the CdS buffer layer within the conventional Sb 2Se 3 cell configuration. In this study, we examined the influence of alterations in energy levels at the Cd 1-xZn xS/Sb 2(S 1-ySe y) 3 junction. Our research demonstrates that by utilizing an Sb 2(S 1-ySe y) 3 absorber layer with a Se concentration of 0.8 and a Cd 1-xZn x S buffer with a Zn mole fraction of 0.7, the cell efficiency can be enhanced from 9.2% to 15.6%. The presented solar cell undergoes optimization of crucial design factors, comprising the thickness of the buffer and absorber layers, as well as their doping concentration. These optimizations are achieved through the utilization of the grey wolf optimization algorithm and fuzzy system, for the first time. By meticulously adjusting each of the aforementioned key design parameters, we were able to achieve an impressive efficiency of approximately 18% for the suggested Sb 2(S 0·2Se 0.8) 3/Cd 0·3Zn 0·7S cell.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Phase-change materials and chalcogenides
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (74)
Show source-provided references
1. Influence of S-content ratios on the defect properties of Sb2(Sx, Se1–x)3 thin-film solar cells10.1016/j.solmat.2023.112501 ↗
2. Design and analysis of Sb2S3/Si thin film tandem solar cell10.1016/j.solmat.2023.112210 ↗
3. Optimization of bifacial Ge-incorporated Sb2Se3 thin-film solar cells by modeling Cu2O back buffer layer10.1016/j.solmat.2023.112399 ↗
4. Controlled conduction band offset in Sb2Se3 solar cell through introduction of (Zn,Sn)O buffer layer to improve photovoltaic performance: a simulation study10.1016/j.solmat.2023.112492 ↗
5. Enhanced performance of Graphene/AlGaAs/GaAs heterostructure Schottky solar cell using AlGaAs drainage10.1007/s10854-021-07651-2 ↗
6. Modeling of GaAsxP1-x/CIGS tandem solar cells under stress conditions10.1016/j.spmi.2021.106860 ↗
7. Improvement of CIGS solar cell efficiency with graded bandgap absorber layer10.1007/s10854-020-04971-7 ↗
8. A review on solar-powered cooling systems coupled with parabolic dish collector and linear Fresnel reflector10.1007/s11356-022-19993-3 ↗
9. Route towards low cost-high efficiency second generation solar cells: current status and perspectives10.1007/s10854-014-2196-4 ↗
10. Improving photocurrent in Sb2Se3 thin-film solar cells through Sb2S3 electron reflector layer: a simulation study10.1002/adts.202300594 ↗
11. Solar cell efficiency tables (version 62)10.1002/pip.3726 ↗
12. Cd-free Cu(in,Ga)(Se,S)2 thin-film solar cell with Record efficiency of 23.3510.1109/JPHOTOV.2019.2937218 ↗
13. A review on additives for halide perovskite solar cells
14. Improving the efficiency of CZTSSe thin-film solar cells using an optimized Al2O3 rear surface passivation layer10.1007/s10854-023-09818-5 ↗
15. Effect of In(O,S) buffer layer on the band alignment and the performance of CZT(S,Se) thin film solar cells, Mater
16. Insights into interface and bulk defects in a high efficiency kesterite-based device10.1039/D0EE02004D ↗
17. Is it possible to Develop complex S–Se graded band gap profiles in kesterite-based solar cells?10.1021/acsami.9b09813 ↗
18. Controlling the anionic ratio and gradient in kesterite technology10.1021/acsami.1c21507 ↗
19. Concurrent investigation of antimony chalcogenide (Sb2Se3 and Sb2S3)-based solar cells with a potential WS2 electron transport layer10.1016/j.heliyon.2022.e12034 ↗
20. Performance enhancement of Sb2Se3 solar cell using a back surface field layer: a numerical simulation approach10.1016/j.solmat.2020.110919 ↗
21. Numerical simulation and performance evaluation of highly efficient Sb2Se3 solar cell with tin sulfide as hole transport layer10.1002/pssb.202000630 ↗
22. Sb2S3 solar cells10.1016/j.joule.2018.04.003 ↗
23. Highly improved Sb2S3 sensitized-inorganic–organic heterojunction solar cells and quantification of traps by deep-level transient spectroscopy10.1002/adfm.201304238 ↗
24. Sb2Se3 thin-film solar cells exceeding 10% power conversion efficiency enabled by injection vapor deposition technology10.1002/adma.202202969 ↗
25. Impact of loss mechanisms through defects on Sb2(S1-xSex)3/CdS solar cells with p-n structure
26. Analysis of hole transport layer and electron transport layer materials in the efficiency improvement of Sb2(Se1−x S x)3 solar cell10.1002/pssb.202200342 ↗
27. Theoretical insight into high-efficiency triple-junction tandem solar cells via the band engineering of antimony chalcogenides10.1002/solr.202000800 ↗
28. Efficient Sb2(S,Se)3/Zn(O,S) solar cells with high open-circuit voltage by controlling sulfur content in the absorber-buffer layers10.1016/j.solener.2021.09.039 ↗
29. Efficient inorganic-organic heterojunction solar cells employing Sb2(sx/Se1-x)3 graded-composition sensitizers10.1002/aenm.201301680 ↗
30. Water additive enhanced solution processing of alloy Sb2(S1−xSex)3-based solar cells10.1002/solr.201900582 ↗
31. High-throughput method to deposit continuous composition spread Sb2(SexS1 − x)3 thin film for photovoltaic application10.1002/pip.2980 ↗
32. Efficient double buffer layer Sb2 (SexS1–x)3 thin film solar cell via single source evaporation10.1002/solr.201800144 ↗
33. Antimony sulfide selenide prototype photovoltaic modules surpassing 4% conversion efficiency under the sun – a technological outlook10.1016/j.solener.2019.06.079 ↗
34. HTL-free Sb2(S, Se)3 solar cells with an optimal detailed balance band gap10.1021/acsami.1c10758 ↗
35. Hydrothermal deposition of antimony selenosulfide thin films enables solar cells with 10% efficiency10.1038/s41560-020-0652-3 ↗
36. Manipulating the electrical properties of Sb2(S,Se)3 film for high-efficiency solar cell10.1002/aenm.202002341 ↗
37. Alternative buffer layers in Sb2Se3 thin‐film solar cells to reduce open‐circuit voltage offset10.1016/j.solener.2020.03.115 ↗
38. Towards high efficiency Cd-Free Sb2Se3 solar cells by the band alignment optimization10.1016/j.solmat.2020.110581 ↗
39. Effect of the junction barrier on current–voltage distortions in the Sb2Se3/Zn(O,S) solar cells10.1016/j.optmat.2021.111098 ↗
40. An analytical model for Sb2Se3 thin-film solar cells by considering current-voltage distortion10.1002/adts.202200438 ↗
41. Improvement in Sb2Se3 solar cell efficiency through band alignment engineering at the buffer/absorber interface10.1021/acsami.8b17611 ↗
42. Efficient Se-rich Sb2Se3/CdS planar heterojunction solar cells by sequential processing: control and influence of Se content10.1002/solr.202070075 ↗
43. A theoretical study on Sb2S3 solar cells: the path to overcome the efficiency barrier of 810.1016/j.solmat.2019.110123 ↗
44. Simulation analysis of Cd1-xZnxS/Sb2(Se1-xSx)3 solar cells with n-i-p structure10.1016/j.solener.2021.05.092 ↗
45. Prospective efficiency boosting of full-inorganic single-junction Sb2(S, Se)3 solar cell10.1016/j.solmat.2022.112001 ↗
46. Modelling polycrystalline semiconductor solar cells10.1016/S0040-6090(99)00825-1 ↗
47. 9.2%-efficient core-shell structured antimony selenide nanorod array solar cells10.1038/s41467-018-07903-6 ↗
48. A review of Sb2Se3 photovoltaic absorber materials and thin-film solar cells10.1016/j.solener.2020.03.009 ↗
49. Evaluation of different methods for solar cells/modules parameters extraction10.1016/j.solener.2019.12.010 ↗
50. Parameters extraction of solar cells – a comparative examination of three methods10.1016/j.solmat.2013.11.011 ↗
51. A novel parameter extraction method for the one-diode solar cell model10.1016/j.solener.2010.03.012 ↗
52. Optimal extraction of solar cell parameters using pattern search10.1016/j.renene.2012.01.082 ↗
53. Parameters identification of PV solar cells and modules using flexible particle swarm optimization algorithm10.1016/j.energy.2019.04.218 ↗
54. Parameter estimation of PV solar cells and modules using whippy harris hawks optimization algorithm10.1016/j.egyr.2021.06.085 ↗
55. Coyote optimization algorithm for parameters estimation of various models of solar cells and PV modules10.1109/ACCESS.2020.3000770 ↗
56. Parameters identification of photovoltaic cells using improved version of the chaotic grey wolf optimizer10.1016/j.ijleo.2021.167150 ↗
57. Multi-group grey wolf optimizer (MG-GWO) for estimating photovoltaic solar cell model10.1007/s10973-020-09895-2 ↗
58. Grey wolf optimizer10.1016/j.advengsoft.2013.12.007 ↗
59. Wang · 1996
60. Fuzzy sets10.1016/S0019-9958(65)90241-X ↗
61. Quasi-one-dimensional Sb2(S,Se)3 alloys as bandgap-tunable and defect-tolerant photocatalytic semiconductors10.1063/5.0013217 ↗
62. Hydrazine solution processed Sb2S3, Sb2Se3 and Sb2(S1−xSex)3 film: molecular precursor identification, film fabrication and band gap tuning
63. Sb2(S1−xSex)3 solar cells: the impact of radiative and non-radiative loss mechanisms10.1088/1361-6463/aaddea ↗
64. Evaluation of Cd1–xZnxS as electron transport layer in superstrate and inverted configurations of Sb2Se3 solar cells with n-i-p structure10.1088/1361-6641/abc7d0 ↗
65. II–VI compound thin films for windows in heterojunction solar cells10.1016/0022-0248(90)90823-4 ↗
66. First-principles calculations of structural, electronic and optical properties of CdTexS1-x and Cd1-xZnxS ternary alloys
67. Over 6% certified Sb2(S,Se)3 solar cells fabricated via in situ hydrothermal growth and postselenization
68. Pulsed laser deposition of antimony selenosulfide thin film for efficient solar cells10.1063/1.5139467 ↗
69. Bandgap grading via sputtering and post-selenization using SeS2 powder enabling Sb2(S,Se)3 solar cells with 7.1% efficiency10.1016/j.solmat.2023.112464 ↗
70. Over 7% efficiency of Sb2(S,Se)3 solar cells via V-shaped bandgap engineering10.1002/solr.202000220 ↗
71. Fabricating over 7%-efficient Sb2(S,Se)3 thin-film solar cells by vapor transport deposition using Sb2Se3 and Sb2S3 mixed powders as the evaporation source10.1016/j.jpowsour.2021.229737 ↗
72. Sequential coevaporation and deposition of antimony selenosulfide thin film for efficient solar cells10.1002/adma.202006689 ↗
73. Efficient Sb2(S,Se)3 solar cells via monitorable chemical bath deposition10.1039/D2TA01465C ↗
74. Band gap and defect engineering for high-performance cadmium-free Sb2(S,Se)3 solar cells and modules10.1002/adfm.202209601 ↗