Boosting conversion efficiency by bandgap engineering of ecofriendly antimony trisulfide indoor photovoltaics via a modeling approach
Source abstract
Abstract
With the exponential growth of the Internet of Things (IoT), indoor photovoltaics (IPVs) have emerged as a pivotal technology for powering low-power devices, drawing heightened interest due to their adaptability to indoor environments. The Photovoltaic Conversion Efficiency (PCE) of IPV cells is critically dependent on their ability to match the indoor spectrum with the device`s response characteristics. In this realm, Antimony Trisulfide (Sb 2S 3), characterized by its wide bandgap and high absorption coefficient, emerges as a promising candidate for low-light applications. Our study focuses on the modeling and numerical analysis of Sb 2S 3 thin-film IPV cells by wxAMPS software, aiming to refine both the device structure and its photoelectric performance for effective indoor light harvesting. In a strategic shift from conventional CdS materials, we utilized SnO 2 —known for its high transmissivity, non-toxicity, and wide bandgap—as the electron transport layer (ETL) in Sb 2S 3 IPV cells. This substitution notably enhanced the short-wave response, elevating the spectral response from 45 % to 80 % at 400 nm. Additionally, we introduced a bandgap-tunable ZnOS buffer layer. This innovation proved instrumental in rectifying the band alignment mismatch between SnO 2 and Sb 2S 3 layer, thereby optimizing interfacial electron transport properties. The integration of the ZnOS buffer layer effectively improved the fill factor from 40.0 % to 64.7 % of the Sb 2S 3 IPV cell by solving the band mismatch problem. The resulting optimized Sb 2S 3 IPV cell demonstrated exceptional response characteristics across the full visible spectrum (400–750 nm) and showed notable photoelectric performance under both fluorescent lamps (FLs) and light-emitting diodes (LEDs). Moreover, a detailed analysis was conducted on the performance differences of the device under indoor light sources compared to solar spectrum conditions, along with the underlying mechanisms. Finally, the Sb 2S 3 IPV cell achieved a peak theoretical efficiency of 46.25 % under cold white FL lighting, a testament to the optimal match between the device structure and this specific emission power spectrum. This modeling research not only underscores the feasibility of employing antimony-based photovoltaic technologies in indoor settings but also offers theoretical guidance for further advancements in this domain.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Perovskite Materials and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (84)
Show source-provided references
1. Recent progress in solar cell technology for low-light indoor applications, Curr. Altern
2. Full‐dimensional grain boundary stress release for flexible perovskite indoor photovoltaics
3. Halide perovskites for indoor photovoltaics: the next possibility10.1021/acsenergylett.2c02268 ↗
4. Applications of graphene in five senses, nervous system, and artificial muscles10.1021/acssensors.2c02790 ↗
5. Applications of MXenes in human-like sensors and actuators10.1007/s12274-022-5272-8 ↗
6. Toward smart sensing by MXene
7. Br vacancy defects healed perovskite indoor photovoltaic modules with certified power conversion efficiency exceeding 3610.1002/advs.202204138 ↗
8. Lead‐free perovskite‐inspired absorbers for indoor photovoltaics
9. Low-trap-density CsPbX3 film for high-efficiency indoor photovoltaics10.1021/acsami.1c25207 ↗
10. From 33% to 57%–an elevated potential of efficiency limit for indoor photovoltaics10.1039/C9TA11894B ↗
11. Modeling solar cells: a method for improving their efficiency10.1016/j.mseb.2012.01.010 ↗
12. Unprecedentedly high indoor performance (efficiency> 34%) of perovskite photovoltaics with controlled bromine doping10.1016/j.nanoen.2020.104984 ↗
13. Perovskite photovoltaics for dim‐light applications10.1002/adfm.201503448 ↗
14. 40.1% record low‐light solar‐cell efficiency by holistic trap‐passivation using micrometer‐thick perovskite film10.1002/adma.202100770 ↗
15. Van der Waals force-assisted heat-transfer engineering for overcoming limited efficiency of flexible perovskite solar cells10.1021/acsenergylett.2c01391 ↗
16. Ma · 2023
17. Photovoltaic performance of Organic Photovoltaics for indoor energy harvester10.1016/j.orgel.2017.05.023 ↗
18. Comparison of indoor and outdoor performance measurements of recent commercially available solar modules10.1002/pip.977 ↗
19. A novel multi‐sulfur source collaborative chemical bath deposition technology enables 8%‐efficiency Sb2S3 planar solar cells
20. Gradient bandgap modification for highly efficient carrier transport in antimony sulfide-selenide tandem solar cells10.1016/j.solmat.2022.111926 ↗
21. Selective preferred orientation for high-performance antimony selenide thin-film solar cells via substrate surface modulation10.1016/j.jallcom.2022.168593 ↗
22. Epitaxial growth of vertically aligned antimony selenide nanorod arrays for heterostructure based self‐powered photodetector10.1002/adom.202200816 ↗
23. Thermally driven point defect transformation in antimony selenosulfide photovoltaic materials10.1002/adma.202208564 ↗
24. Carrier recombination suppression and transport enhancement enable high‐performance self‐powered broadband Sb2Se3 photodetectors10.1002/inf2.12400 ↗
25. Temperature sensitivity of adjustable band gaps of Sb2(S, Se)3 solar cells via vapor transport deposition10.1016/j.solmat.2023.112582 ↗
26. Interfacial engineering by applying double CdS structure electron transport layer for high-performance Sb2(S, Se)3 solar cells10.1016/j.ceramint.2023.04.079 ↗
27. Suppressing buried interface nonradiative recombination losses toward high‐efficiency antimony triselenide solar cells
28. Regulating energy band alignment via alkaline metal fluoride assisted solution post‐treatment enabling Sb2(S, Se)3 solar cells with 10.7% efficiency
29. Microstructural and optical properties of Sb2S3 film thermally evaporated from antimony pentasulfide and efficient planar solar cells10.1002/pssr.201800025 ↗
30. Efficient and novel Sb2S3 based solar cells with chitosan/poly (ethylene glycol)/electrolyte blend10.1002/er.3899 ↗
31. Enhanced hydrothermal heterogeneous deposition with surfactant additives for efficient Sb2S3 solar cells10.1016/j.cej.2022.136474 ↗
32. Thermal evaporation and characterization of Sb2Se3 thin film for substrate Sb2Se3/CdS solar cells10.1021/am502427s ↗
33. Buried homojunction in CdS/Sb2Se3 thin film photovoltaics generated by interfacial diffusion10.1063/1.4991539 ↗
34. The effects of cadmium toxicity10.3390/ijerph17113782 ↗
35. Grain size dependence of the bandgap in chemical bath deposited CdS thin films10.1016/j.solmat.2004.01.002 ↗
36. Boosting performance of perovskite solar cells with Graphene quantum dots decorated SnO2 electron transport layers10.1016/j.apsusc.2019.145099 ↗
37. 17.78% efficient low-temperature carbon-based planar perovskite solar cells using Zn-doped SnO2 electron transport layer10.1016/j.apsusc.2019.01.237 ↗
38. Enhanced charge carrier transport via efficient grain conduction mode for Sb2Se3 solar cell applications10.1016/j.apsusc.2022.153169 ↗
39. Suppressing the trapping process by interfacial charge extraction in antimony selenide heterojunctions10.1021/acsenergylett.0c02660 ↗
40. Bandgap tunable CdS:O as efficient electron buffer layer for high-performance Sb2Se3 thin film solar cells10.1016/j.solmat.2019.01.043 ↗
41. Carrier transport enhancement mechanism in highly efficient antimony selenide thin‐film solar cell10.1002/adfm.202213941 ↗
42. Modeling a tandem solar cell based on Sb2S3 and Sb2Se3 absorber layers10.1016/j.mseb.2024.117302 ↗
43. Numerical analysis and design of high performance HTL-free antimony sulfide solar cells by SCAPS-1D10.1016/j.optmat.2021.111880 ↗
44. Design and simulation of Sb2S3 solar cells based on monolayer graphene as electron transport layer10.1016/j.optmat.2020.110791 ↗
45. Design simulation analysis for large enhancement in efficiency of sulphur substituted Sb2S3 absorber based solar cell10.1016/j.ijleo.2023.170564 ↗
46. Numerical analysis of Al/Gr/ETL/MoS2/Sb2S3/Ni solar cell using non-toxic In2S3/SnS2/ZnSe electron transport layer10.1016/j.ijleo.2023.170875 ↗
47. Sb2Se3 versus Sb2S3 solar cell: a numerical simulation10.1016/j.solener.2021.09.080 ↗
48. First principles prediction of the elastic, electronic, and optical properties of Sb2S3 and Sb2Se3 compounds10.1016/j.solidstatesciences.2012.06.003 ↗
49. Numerical modelling and analysis of earth abundant Sb2S3 and Sb2Se3 based solar cells using SCAPS-1D10.1016/j.solmat.2021.111184 ↗
50. Band offset engineering in antimony sulfide (Sb2S3) solar cells, using SCAPS simulation: a route toward PCE> 1010.1016/j.ijleo.2023.170868 ↗
51. Rotational design of charge carrier transport layers for optimal antimony trisulfide solar cells and its integration in tandem devices10.1016/j.solmat.2019.110279 ↗
52. On the prospect of CZTSSe-based thin film solar cells for indoor photovoltaic applications: a simulation study10.1063/1.5099274 ↗
53. Indoor-type photovoltaics with organic solar cells through optimal design10.1016/j.dyepig.2018.06.025 ↗
54. Organic tandem solar cells under indoor light illumination10.1002/pip.3301 ↗
55. Efficiency simulations of thin film chalcogenide photovoltaic cells for different indoor lighting conditions10.1016/j.tsf.2011.01.362 ↗
56. A proposal for typical artificial light sources for the characterization of indoor photovoltaic applications10.3390/en7031500 ↗
57. Tailoring triple‐anion perovskite material for indoor light harvesting with restrained halide segregation and record high efficiency beyond 36
58. Crystalline grain engineered CsPbIBr2 films for indoor photovoltaics10.1016/j.apsusc.2022.152865 ↗
59. Hysteresis in hybrid perovskite indoor photovoltaics
60. A new simulation software of solar cells—wxAMPS10.1016/j.solmat.2011.10.010 ↗
61. Efficient and stable flexible Sb2Se3 thin film solar cells enabled by an epitaxial CdS buffer layer10.1016/j.nanoen.2021.106019 ↗
62. Precise preparation of CdS thin films for efficient Sb2S3–ySey thin-film solar cells10.1021/acsaem.3c00859 ↗
63. Review on the application of SnO2 in perovskite solar cells10.1002/adfm.201802757 ↗
64. Dopant-free Spiro-OMeTAD as hole transporting layer for stable and efficient perovskite solar cells10.1016/j.orgel.2019.06.039 ↗
65. Optimization of layer thickness of ZnO based perovskite solar cells using SCAPS 1D
66. Strong valence-band offset bowing of ZnO1−xSx enhances p-type nitrogen doping of ZnO-like alloys10.1103/PhysRevLett.97.146403 ↗
67. Large‐area wide bandgap indoor organic photovoltaics for self‐sustainable IoT applications10.1002/aesr.202200117 ↗
68. Organic photovoltaic cells for indoor applications: opportunities and challenges10.1021/acsami.0c10444 ↗
69. Reduced energy loss in SnO2/ZnO bilayer electron transport layer-based perovskite solar cells for achieving high efficiencies in outdoor/indoor environments10.1039/D0TA04721J ↗
70. Theoretical analysis on effect of band offsets in perovskite solar cells10.1016/j.solmat.2014.10.036 ↗
71. High-efficiency electron transport layer-free perovskite/GeTe tandem solar cell: numerical simulation10.3390/cryst12070878 ↗
72. Design and simulation investigations on electron transport layer-free in tin-based pn homojunction perovskite solar cells
73. Dual-function of CdCl2 treated SnO2 in Sb2Se3 solar cells10.1016/j.apsusc.2020.147632 ↗
74. Combined optical-electrical modeling of perovskite solar cell with an optimized design10.1016/j.optmat.2020.110259 ↗
75. Device characteristics of CZTSSe thin‐film solar cells with 12.6% efficiency10.1002/aenm.201301465 ↗
76. A highly crystalline non-fullerene acceptor enabling efficient indoor organic photovoltaics with high EQE and fill factor10.1016/j.joule.2021.03.020 ↗
77. CdTe solar cell performance under low-intensity light irradiance10.1016/j.solmat.2015.09.043 ↗
78. Enhanced hole selecting behavior of WO3 interlayers for efficient indoor organic photovoltaics with high fill-factor10.1016/j.apsusc.2020.146840 ↗
79. Effect of the chemical composition of co‐sputtered Zn(O, S) buffer layers on Cu(In, Ga)Se2 solar cell performance10.1002/pssa.201431388 ↗
80. Investigations on the effect of buffer layer on CMTS based thin film solar cell using SCAPS 1-D10.1016/j.optmat.2022.112150 ↗
81. Performance optimization of CH3NH3Pb(I1-xBrx)3 based perovskite solar cells by comparing different ETL materials through conduction band offset engineering10.1016/j.optmat.2020.109897 ↗
82. Comparing and quantifying indoor performance of organic solar cells10.1002/aenm.202101474 ↗
83. The correlation between limiting efficiency of indoor photovoltaics and spectral characteristics of multi-color white LED sources10.1088/1361-6463/abfdda ↗
84. Quasiepitaxy strategy for efficient full‐inorganic Sb2S3 solar cells10.1002/adfm.201901720 ↗