Analysis of moisture-induced degradation of thin-film photovoltaic module
Source abstract
Abstract
Abstract To enhance the reliability of the thin-film solar cell technologies, it is required to analyze and understand the moisture-induced degradation. In this study, the moisture induced degradation of glass-to-glass CIGS module are comprehensively analyzed. CIGS modules are fabricated and tested under damp-heat conditions with periodical measurement of the electrical characteristics. Individual layers of the module are also investigated experimentally and the moisture induced degradation is discussed. A modified method to extract the diode model parameters from degraded I–V curves is proposed and applied to the degraded data. Finally, the degradation rates are modelled and the effect of model parameters degradation on the power of module are quantitatively compared. It suggests that the power degradation of CIGS module under the damp-heat environment is more affected by the enhanced recombination of the absorber layer than the degradation of the metal layer or the leakage over layers.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Photovoltaic System Optimization Techniques · Silicon and Solar Cell Technologies · Thin-Film Transistor Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. Fraunhofer Institute for Solar Energy Systems
2. National Renewable Energy Laboratory Photovoltaic Research
3. A cost roadmap for silicon heterojunction solar cells10.1016/j.solmat.2015.12.026 ↗
4. Thin‐film CuInSe2/CdS heterojunction solar cells10.1063/1.89041 ↗
5. An analysis of glass–glass CIGS manufacturing costs10.1016/j.solmat.2016.04.029 ↗
6. CIGS PV reliability-Current practices, challenges and approaches
7. Photovoltaic degradation rates—an analytical review10.1002/pip.1182 ↗
8. Stability of Cu (In, Ga) Se2 solar cells: a literature review10.1016/j.solener.2016.04.010 ↗
9. A review of thin film solar cell technologies and challenges10.1016/j.rser.2016.12.028 ↗
10. Progress in thin film CIGS photovoltaics–Research and development, manufacturing, and applications10.1002/pip.2811 ↗
11. Performance degradation of various PV module technologies in tropical Singapore10.1109/JPHOTOV.2014.2338051 ↗
12. A study of the degradation mechanisms of ultra-thin CIGS solar cells submitted to a damp heat environment
13. Experimental evidence of PID effect on CIGS photovoltaic modules10.3390/en13030537 ↗
14. A study on the degradation rates and the linearity of the performance decline of various thin film PV technologies10.1016/j.solener.2019.06.067 ↗
15. Numerical analysis of degradation kinetics in CdTe thin films10.1016/j.solener.2015.05.041 ↗
16. Modeling of rates of moisture ingress into photovoltaic modules10.1016/j.solmat.2006.04.002 ↗
17. Failure mode and effect analysis of a large scale thin-film CIGS photovoltaic module10.1016/j.engfailanal.2017.02.004 ↗
18. Stability of CIGS solar cells under illumination with damp heat and dry heat: a comparison10.1016/j.solmat.2016.12.039 ↗
19. Damp heat and thermal cycling-induced degradation mechanism of AZO and CIGS films in Cu (In, Ga) Se2 photovoltaic modules10.1016/j.cap.2014.12.023 ↗
20. Cu (In, Ga) Se2-based thin-film photovoltaic modules optimized for long-term performance10.1016/S0927-0248(02)00101-0 ↗
21. Behavior of Cu (In, Ga) Se2 solar cells under light/damp heat over time10.1016/S0026-2714(03)00355-X ↗
22. Time‐dependent open‐circuit voltage in CuInSe2/CdS solar cells: theory and experiment10.1063/1.338377 ↗
23. The effects of sweep rate, voltage bias and light soaking on the measurement of CIS-based solar cell characteristics
24. Examination of lifetime-limiting failure mechanisms in CIGSS-based PV minimodules under environmental stress
25. Degradation of ZnO-based window layers for thin-film CIGS by accelerated stress exposures
26. Moisture-induced surface corrosion in AZO thin films formed by atomic layer deposition10.1109/TDMR.2012.2186574 ↗
27. Failure analysis of Cu (In, Ga) Se2 photovoltaic modules: degradation mechanism of Cu (In, Ga) Se2 solar cells under harsh environmental conditions10.1002/pip.2497 ↗
28. Copper indium gallium selenide based solar cells–a review10.1039/C7EE00826K ↗
29. A theoretical modeling of the Cu (In, Ga) Se2 solar cell
30. Equivalent circuit model for Cu (in, Ga) Se2 solar cells operating at different temperatures and irradiance10.3390/electronics7110324 ↗
31. Properties of high-efficiency CIGS thin-film solar cells
32. Comparison of CIGS solar cells made with different structures and fabrication techniques10.1109/JPHOTOV.2016.2616188 ↗
33. Comprehensive approach to modeling and simulation of photovoltaic arrays10.1109/TPEL.2009.2013862 ↗
34. Wenham · 2013
35. The recombination parameter J010.1016/j.egypro.2014.08.073 ↗
36. The origin of ideality factors n> 2 of shunts and surfaces in the dark IV curves of Si solar cells
37. Anomalous dark current ideality factor (n> 2) in thin-film solar cells: the role of grain-boundary defects
38. Identifying parasitic current pathways in CIGS solar cells by modelling dark J–V response10.1002/pip.2582 ↗
39. Analytic findings in the electroluminescence characterization of crystalline silicon solar cells10.1063/1.2431075 ↗
40. Reaction rate studies for the corrosion of metals in acids—I, iron in mineral acids10.5006/1.3579270 ↗
41. On moisture diffusion modeling using thermal-moisture analogy10.1115/1.2804090 ↗
42. Experimental characterization and simulation of water vapor diffusion through various encapsulants used in PV modules10.1016/j.solmat.2013.04.007 ↗