Controlled back slope of Ga/(In+Ga) profile in Cu(In,Ga)Se2 absorber fabricated by multi layer precursor method for improvement of its photovoltaic performance
Source abstract
Abstract
Abstract Cu(In,Ga)Se2 (CIGS) absorbers with several Ga/III, Ga/(In+Ga) ratio, profiles were deposited by the so-called “multi layer precursor method” consisting of Ga-Se/In-Se/Cu-Se stacks. The effects of average Ga/III ratios and back slopes of the Ga/III profiles on the photovoltaic performance were investigated. The optimum average Ga/III ratio of approximately 0.36 leads to the appropriate average band-gap energy as well as sufficiently long carrier lifetime in CIGS absorber, thus enhancing open-circuit voltage. In addition, the back slope of 0.50 μm−1, defined as the ratio of the change in Ga/III ratio to the change in the depth range from 1 to 2 μm from CIGS surface, induces back surface field of 0.34 V/μm, thereby increasing short-circuit current density. Ultimately, the CIGS absorber on flexible stainless steel substrate with the double graded Ga/III profile (the average Ga/III of 0.36 and the back slope of 0.50 μm−1) was fabricated by the multi layer precursor method. This results in the 14.36%-efficient CIGS solar cell on the flexible substrate without an anti-reflective layer.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Copper-based nanomaterials and applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. Epitaxial thin film crystalline silicon solar cells on low cost silicon carriers
2. Solar cell efficiency tables (version 43)10.1002/pip.2452 ↗
3. Highly efficient Cu(In,Ga)Se2 solar cells grown on flexible polymer films10.1038/nmat3122 ↗
4. High-efficiency Cu(In,Ga)Se2 cells and modules10.1016/j.solmat.2013.05.002 ↗
5. Potassium-induced surface modification of Cu(In,Ga)Se2 thin films for high-efficiency solar cells10.1038/nmat3789 ↗
6. A comparison between thin film solar cells made from co-evaporaed CuIn1−xGaxSe2 using a one-stage process versus a three-stage process
7. Electronic properties of Cu(In,Ga)Se2 solar cells on stainless steel foils with diffusion barrier10.1002/pip.1247 ↗
8. Compositional investigation of potassium doped Cu(In,Ga)Se2 solar cells with efficiencies up to 20.8%10.1002/pssr.201409040 ↗
9. Determination of open-circuit voltage in Cu(In,Ga)Se2 solar cell by averaged Ga/(In+Ga) near its absorber surface10.1063/1.4819087 ↗
10. Relationship between open-circuit voltage in Cu(In,Ga)Se2 solar cell and peak position of (220/204) preferred orientation near its absorber surface10.1063/1.4832995 ↗
11. Investigation of Cu(In,Ga)Se2 absorber by time-resolved photoluminescence for improvement of its photovoltaic performance10.1016/j.solmat.2014.08.012 ↗
12. Multi layer precursor method for Cu(In,Ga)Se2 solar cells fabricated on flexible substrates10.7567/JJAP.53.05FW03 ↗
13. Solae cell efficiency tables (version 39)10.1002/pip.2163 ↗
14. Effect of NaF coevaporation on structural properties of Cu(In,Ga)Se2 thin films10.1016/S0040-6090(03)00246-3 ↗
15. Efficiency enhancement of Cu(In,Ga)Se2 solar cells due to post-deposition Na incorporation10.1063/1.1646758 ↗
16. Surface characterization of chemically treated Cu(In, Ga)Se2 thin films10.1143/JJAP.35.4760 ↗
17. Influence of KCN treatment on CuInS2 thin films10.1016/0169-4332(95)00236-7 ↗
18. Effect of residual copper selenide on CuInGaSe2 solar cells10.1016/j.sse.2010.11.019 ↗
19. Effect of Cu deficiency on the optical bowing of chalcopyrite Cu In1−x GaxSe210.1063/1.2089154 ↗
20. Effect of Ga content on defect states in CuIn1−xGaxSe2 photovoltaic devices10.1063/1.1485301 ↗
21. Theoretical analysis of the effect of conduction band offset of window/CIS layers on performance of CIS solar cells using device simulation10.1016/S0927-0248(00)00266-X ↗