journal article·2017-04

High performance perovskite solar cells fabricated under high relative humidity conditions

John Ciro, Rafael Betancur, Santiago Mesa, Franklin Jaramillo

Publisher page

Abstract

Abstract The development of efficient perovskite solar devices fully fabricated in air conditions at low temperature is investigated. A 10.0% average efficiency was achieved for a CH3NH3PbI3 p-i-n planar perovskite solar cell with null hysteresis processed in an environment with relative humidity as high as 70%. This result was enabled by a fine control over the perovskite precursor composition, adapting the solvent engineering process to ambient air conditions and implementing nickel oxide as hole-transporting layer. The presented strategy contributes towards the establishment of processing methodologies leading to scale up high performance perovskite solar cells where processing in ambient air at low temperature is highly desirable.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Perovskite Materials and Applications · Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. NREL, Best research-cell efficiencies, (2016) Rev. 02/11/2016.
2. Optical analysis of perovskite/silicon tandem solar cells10.1039/C6TC01276K ↗
3. Ultimate efficiency limit of single-junction perovskite and dual-junction perovskite / silicon two- terminal devices and dual-junction perovskite / silicon two-terminal devices10.7567/JJAP.54.08KD04 ↗
4. Monilithic perovskite/silicon-heterojunction tandem solar cells processed at low temperature10.1039/C5EE02965A ↗
5. Semitransparent perovskite solar cell with sputtered front and rear electrodes for a four-terminal tandem10.1109/JPHOTOV.2016.2521479 ↗
6. Efficient Monolithic Perovskite/Silicon Tandem Solar Cell with Cell Area >1 cm210.1021/acs.jpclett.5b02686 ↗
7. Toward large scale roll-to-roll production of fully printed perovskite solar cells10.1002/adma.201404598 ↗
8. Upscaling of Perovskite Solar Cells: Fully Ambient Roll Processing of Flexible Perovskite Solar Cells with Printed Back Electrodes10.1002/aenm.201500569 ↗
9. Effect of zinc addition on properties of cadmium sulfide layer and performance of Cu(In,Ga)Se2 solar cell10.1016/j.tsf.2012.11.077 ↗
10. R&D pilot line production of multi-crystalline Si solar cells exceeding cell efficiencies of 1810.1016/j.egypro.2011.06.142 ↗
11. Low cost processing of CIGS thin film solar cells10.1016/j.solener.2004.08.015 ↗
12. The importance of moisture in hybrid lead Halide perovskite thin film Fabrication10.1021/acsnano.5b03626 ↗
13. Nucleation and crystal growth of organic-inorganic lead halide perovskites under different relative humidity10.1021/acsami.5b00895 ↗
14. Moisture assisted perovskite film growth for high performance solar cells10.1063/1.4901510 ↗
15. Interface engineering of highly efficient perovskite solar cells10.1126/science.1254050 ↗
16. 15.76% efficiency perovskite solar cells prepared under high relative humidity: importance of PbI2 morphology in two-step deposition of CH3NH3PbI310.1039/C5TA00658A ↗
17. Intrinsic charge carrier dynamics and device stability of perovskite/ZnO mesostructured solar cells in moisture10.1039/C6TA00614K ↗
18. Efficient and stable perovskite solar cells prepared in ambient air irrespective of the humidity
19. Origin of J-V Hysteresis in Perovskite Solar Cells10.1021/acs.jpclett.6b00215 ↗
20. Interface-dependent ion migration/accumulation controls hysteresis in MAPbI3 solar cells10.1021/acs.jpcc.6b04233 ↗
21. Ionic polarization-induced current–voltage hysteresis in CH3NH3PbX3 perovskite solar cells10.1038/ncomms10334 ↗
22. Pinhole-free and surface-nanostructured NiOx film by room-temperature solution process for high-performance flexible perovskite solar cells with Good stability and Reproducibility10.1021/acsnano.5b07043 ↗
23. Astm Standard, E112-12:Standard Test Methods for Determining Average Grain Size, ASTM Int. E112-12 (2012) pp. 1–27.
24. Stability/instability of conductivity and work function changes of ITO thin films, UV-irradiated in air or vacuum. measurements by the four-probe method and by Kelvin force microscopy10.1016/S0379-6779(00)01337-0 ↗
25. Enhanced optoelectronic quality of perovskite thin films with hypophosphorous acid for planar heterojunction solar cells10.1038/ncomms10030 ↗
26. Advanced Raman Spectroscopy of Methylammonium Lead Iodide: Development of a Non-destructive Characterisation Methodology10.1038/srep35973 ↗
27. Introduction of copper iodide fine particles into a poly(acrylic acid) matrix via a complex of polymer-polyiodide ions10.1039/b507817b ↗
28. Iodine insertion in pentacene thin films investigated by infrared and Raman spectroscopy10.1103/PhysRevB.70.081309 ↗
29. Solvent engineering for high-performance inorganic-organic hybrid perovskite solar cells10.1038/nmat4014 ↗
30. Solvent engineering of spin-coating solutions for planar-structured high-efficiency perovskite solar cells10.1016/S1872-2067(15)60929-9 ↗
31. A fast deposition-Crystallization procedure for highly efficient lead iodide perovskite thin-film solar cells10.1002/ange.201405334 ↗
32. Room temperature, air crystallized perovskite film for high performance solar cells10.1039/C6TA02918C ↗
33. Electrical characterization of PEDOT:PSS beyond humidity saturation10.1016/j.snb.2009.08.055 ↗
34. Crystallization of methyl ammonium lead Halide perovskites: implications for photovoltaic applications Crystallization of methyl ammonium lead Halide perovskites: implications for photovoltaic applications10.1021/ja505556s ↗