journal article·2016-10

New barrier encapsulation and lifetime assessment of printed organic photovoltaic modules

Hasitha C. Weerasinghe, Doojin Vak, Benjamin Robotham, Christopher J. Fell, David Jones, Andrew D. Scully

Publisher page

Abstract

Abstract Organic photovoltaic (OPV) modules printed on plastic substrates are attracting worldwide attention due to advantages such as flexibility, large-scale printability, lightweight, and potential utility for new products. However, exposure to atmospheric oxygen and water vapour is known to cause rapid device degradation and OPV devices thus require encapsulation using materials having ultra-low permeability to these atmospheric constituents to achieve the required operational lifetimes for commercial applications. In this work, various encapsulation architectures using flexible barrier films and adhesives available from commercial suppliers are developed and the lifetime of encapsulated large-area (active area ~50 cm2) fully-printed OPV modules are assessed under ambient laboratory and outdoor conditions. New encapsulation architectures significantly enhance the durability of printed OPV modules, with results showing modules exhibiting a shelf-life of more than 5 years, and no evidence of degradation after 13 months׳ exposure under outdoor conditions.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Thin-Film Transistor Technologies · Silicon and Solar Cell Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. Plastic solar cells: breaking the 10% commercialization barrier10.1117/12.930410 ↗
2. A polymer tandem solar cell with 10.6% power conversion efficiency10.1038/ncomms2411 ↗
3. Single-junction polymer solar cells with high efficiency and photovoltage10.1038/nphoton.2015.6 ↗
4. Best Research-Cell Efficiencies, NREL, in, 〈http://www.nrel.gov/ncpv/images/efficiency_chart.jpg〉, 2016.
5. Roll-to-roll fabrication of polymer solar cells10.1016/S1369-7021(12)70019-6 ↗
6. Cost analysis of roll-to-roll fabricated ITO free single and tandem organic solar modules based on data from manufacture10.1039/C4EE01222D ↗
7. Roll-to-roll gravure printing of organic photovoltaic modulesinsulation of processing defects by an interfacial layer10.1002/pip.2508 ↗
8. Roll-coating fabrication of ITO-free flexible solar cells based on a non-fullerene small molecule acceptor10.1039/C5RA04336K ↗
9. Scalable, ambient atmosphere roll-to-roll manufacture of encapsulated large area, flexible organic tandem solar cell modules10.1039/C4EE01223B ↗
10. Organic photovoltaic modules fabricated by an industrial gravure printing proofer10.1016/j.solmat.2012.10.018 ↗
11. Stability/degradation of polymer solar cells10.1016/j.solmat.2008.01.005 ↗
12. Degradation patterns in water and oxygen of an inverted polymer solar cell10.1021/ja106299g ↗
13. The impact of water vapor transmission rate on the lifetime of flexible polymer solar cells10.1063/1.2975185 ↗
14. Definition of encapsulation barrier requirements: a method applied to organic solar cells10.1016/j.solmat.2011.01.035 ↗
15. Enhancement of the barrier performance in organic/inorganic multilayer thin-film structures by annealing of the parylene layer10.1016/j.materresbull.2014.03.022 ↗
16. Flexible organic-inorganic hybrid layer encapsulation for organic opto-electronic devices10.1016/j.porgcoat.2014.11.015 ↗
17. Influence of moisture out-gassing from encapsulant materials on the lifetime of organic solar cells10.1016/j.solmat.2014.09.030 ↗
18. Interlaboratory outdoor stability studies of flexible roll-to-roll coated organic photovoltaic modules: stability over 10,000h10.1016/j.solmat.2013.04.024 ↗
19. An inter-laboratory stability study of roll-to-roll coated flexible polymer solar modules10.1016/j.solmat.2011.01.010 ↗
20. Outdoor performance of organic photovoltaics: diurnal analysis, dependence on temperature, irradiance, and degradation10.1063/1.4906915 ↗
21. Mechanical degradation and stability of organic solar cells: molecular and microstructural determinants10.1039/C4EE02657H ↗
22. Over 2 years of outdoor operational and storage stability of ITO-free, fully roll-to-roll fabricated polymer solar cell modules10.1002/ente.201500086 ↗
23. Lifetime of organic photovoltaics: linking outdoor and indoor tests10.1016/j.solmat.2015.07.037 ↗
24. Edge sealing for low cost stability enhancement of roll-to-roll processed flexible polymer solar cell modules10.1016/j.solmat.2011.09.064 ↗
25. High efficiency polymer solar cells with long operating lifetimes10.1002/aenm.201100138 ↗
26. A roll-to-roll process to flexible polymer solar cells: model studies, manufacture and operational stability studies10.1039/b823001c ↗
27. Organic and inorganic blocking layers for solution-processed colloidal PbSe nanocrystal infrared photodetectors10.1002/adfm.201001328 ↗
28. Comparison of UV-curing, hotmelt, and pressure sensitive adhesive as roll-to-roll encapsulation methods for polymer solar cells10.1002/adem.201300172 ↗
29. Consensus stability testing protocols for organic photovoltaic materials and devices10.1016/j.solmat.2011.01.036 ↗
30. Y. Kim, N. Kim, H. Kim, S. Graham, The development of thin film barriers for encapsulating organic electronics 2011, in: Proceedings of IEEE 61st Electronic Components and Technology Conference (ECTC), 2011, pp. 2101–2106.10.1109/ECTC.2011.5898808 ↗
31. Reverse gravure coating for roll-to-roll production of organic photovoltaics10.1016/j.solmat.2016.01.015 ↗
32. Spatially resolved photocurrent measurements of organic solar cells: tracking water ingress at edges and pinholes10.1016/j.solmat.2012.10.027 ↗
33. Limited laser beam induced current measurements: a tool for analysing integrated photovoltaic modules10.1088/0957-0233/22/8/085702 ↗
34. Electrical and photo-induced degradation of ZnO layers in organic photovoltaics, advanced energy