Phenomenological morphology design of hybrid organic-inorganic perovskite solar cell for high efficiency and less hysteresis
Source abstract
Abstract
Abstract In this report, a modeling approach is employed to study the effect of the grain boundaries (GBs) and their electronic activity on the performance parameters of the perovskite solar cells (PSCs). Our model is based on the 1- dimensional drift-diffusion framework to engage the electron (hole) defects formed in the GBs and the GB's location through the perovskite layer. Power conversion efficiency (PCE) of the PSC is optimized with regards to the perovskite layer thickness, GBs location and perovskite layer band offset with GBs layer. The results shows that the location or the distribution of the GBs can vary the PCE of PSCs from 12% to around 21%, thereby making proper morphology engineering and passivation of GBs is a chief requirement for achieving high efficiency. PCEs larger than 21% require GB defect densities below 10 15 c m − 2 . It is demonstrated that the band offset of about 100 meV with GB width of 1 nm could effectively suppress the negative impact of the GBs throughout the entire perovskite layer. Interestingly, GBs location at closer points to electron transport layer (ETL)/perovskite interface may give rise to higher PCEs, however, relatively stronger hysteresis in current values is observed. The results here provide insight into the effect of the GBs location and their corresponding type of defects on the hysteresis and the PSC performance and opens up new horizons to find solutions for current PSC's shortcomings.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Perovskite Materials and Applications · Conducting polymers and applications · Organic Electronics and Photovoltaics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. Solar cell efficiency tables (Version 53)10.1002/pip.3102 ↗
2. High-efficiency solution-processed perovskite solar cells with millimeter-scale grains10.1126/science.aaa0472 ↗
3. A facile method to evaluate the influence of trap densities on perovskite solar cell performance10.1039/C9TC00816K ↗
4. Sequential condensation route as a versatile platform for low cost and efficient hole transport material in perovskite solar cell
5. The interplay between trap density and hysteresis in planar heterojunction perovskite solar cells10.1021/acs.nanolett.7b01211 ↗
6. Construction of high performance CH3NH3PbI3-based solar cells by hot-casting technique10.1016/j.solmat.2017.01.009 ↗
7. Enhanced efficiency of hot‐cast large‐area planar perovskite solar cells/modules having controlled chloride incorporation10.1002/aenm.201601660 ↗
8. Tailoring nucleation and grain growth by changing the precursor phase ratio for efficient organic lead halide perovskite optoelectronic devices10.1039/C7TC02928D ↗
9. High-performance perovskite solar cells with large grain-size obtained by the synergy of urea and dimethyl sulfoxide10.1016/j.apsusc.2018.10.141 ↗
10. Additive engineering to improve the efficiency and stability of inverted planar perovskite solar cells10.1039/C8TC02507J ↗
11. High-performance perovskite solar cells with large grain-size obtained by the synergy of urea and dimethyl sulfoxide10.1016/j.apsusc.2018.10.141 ↗
12. Exfoliated graphitic carbon nitride self-recognizing CH3NH3PbI3 grain boundaries by hydrogen bonding interaction for improved perovskite solar cells10.1016/j.solener.2019.01.095 ↗
13. The investigation of the unseen interrelationship of grain size, ionic defects, device physics and performance of perovskite solar cells10.1088/1361-6463/aafea9 ↗
14. Influence of perovskite morphology on slow and fast charge transport and hysteresis in the perovskite solar cells10.1021/acs.jpclett.6b01909 ↗
15. Recombination in perovskite solar cells: significance of grain boundaries, interface traps, and defect ions10.1021/acsenergylett.7b00236 ↗
16. Exploring the performance limiting parameters of perovskite solar cell through experimental analysis and device simulation10.1016/j.solener.2015.09.046 ↗
17. Interactions between molecules and perovskites in halide perovskite solar cells10.1016/j.solmat.2017.09.038 ↗
18. Performance improvement of perovskite solar cells by employing a CdSe quantum dot/PCBM composite as an electron transport layer10.1039/C7TA00203C ↗
19. How measurement protocols influence the dynamic JV characteristics of perovskite solar cells: theory and experiment10.1016/j.solener.2018.08.033 ↗
20. Dynamic electrical behavior of halide perovskite based solar cells10.1016/j.solmat.2016.09.012 ↗
21. Parameters affecting I–V hysteresis of CH3NH3PbI3 perovskite solar cells: effects of perovskite crystal size and mesoporous TiO2 layer10.1021/jz501392m ↗
22. Highly reproducible and photocurrent hysteresis-less planar perovskite solar cells with a modified solvent annealing method10.1016/j.solener.2016.06.068 ↗
23. Origin of high electronic quality in structurally disordered CH3NH3PbI3 and the passivation effect of Cl and O at grain boundaries10.1002/aelm.201500044 ↗
24. Grain-boundary recombination in Cu (In, Ga) Se 2 solar cells10.1063/1.2133906 ↗
25. Microscopic investigation of grain boundaries in organolead halide perovskite solar cells10.1021/acsami.5b09801 ↗
26. Numerical simulation of grain boundary effects in Cu (In, Ga) Se2 thin-film solar cells10.1016/j.tsf.2004.11.043 ↗
27. Local built-in potential on grain boundary of Cu(In,Ga)Se2 thin films10.1063/1.1737796 ↗
28. Facile realization of efficient blocking from ZnO/TiO2 mismatch interface in dye-sensitized solar cells and precise microscopic modeling adapted by circuit analysis10.1088/0022-3727/49/22/225601 ↗
29. Self-assembled ZnO nanosheet-based spherical structure as photoanode in dye-sensitized solar cells10.1007/s11664-017-6000-0 ↗
30. Interfacial modification to optimize stainless steel photoanode design for flexible dye sensitized solar cells: an experimental and numerical modeling approach
31. An alternate method to extract performance characteristics in dye sensitized solar cells10.1016/j.ijleo.2017.10.036 ↗
32. Modeling the time-dependent characteristics of perovskite solar cells10.1016/j.solener.2018.05.082 ↗
33. The role of stabilizing surfactant on capacitance, charge and ion transport in organic nanoparticle-based electronic devices10.1021/acsami.8b19820 ↗
34. Device physics of hybrid perovskite solar cells: theory and experiment10.1002/aenm.201702772 ↗
35. How transport layer properties affect perovskite solar cell performance: insights from a coupled charge transport/ion migration model10.1039/C8EE01576G ↗
36. Classical modelling of grain size and boundary effects in polycrystalline perovskite solar cells10.1016/j.solmat.2018.02.026 ↗
37. Oriented grains with preferred low‐angle grain boundaries in halide perovskite films by pressure‐induced crystallization
38. Numerical simulation of carrier collection and recombination at grain boundaries in Cu (In, Ga) Se 2 solar cells10.1063/1.2917293 ↗
39. Study of thin film poly-crystalline CdTe solar cells presenting high acceptor concentrations achieved by in-situ arsenic doping10.1016/j.solmat.2019.02.025 ↗
40. Evidence of enhanced carrier collection in Cu (in, Ga) Se2 grain boundaries: correlation with microstructure10.1021/acsami.8b02328 ↗
41. Anomalous Grain Boundary Physics in Polycrystalline C u I n S e 2: the Existence of a Hole Barrier10.1103/PhysRevLett.91.266401 ↗
42. Direct observation of copper depletion and potential changes at copper indium gallium diselenide grain boundaries10.1063/1.1906331 ↗
43. Benefit of grain boundaries in organic–inorganic halide planar perovskite solar cells10.1021/acs.jpclett.5b00182 ↗
44. Direct observation of copper depletion and potential changes at copper indium gallium diselenide grain boundaries10.1063/1.1906331 ↗
45. Photovoltaic performance of perovskite solar cells with different grain sizes10.1002/adma.201504144 ↗
46. Lead halide perovskite photovoltaic as a model p–i–n diode10.1021/acs.accounts.5b00436 ↗
47. Revealing underlying processes involved in light soaking effects and hysteresis phenomena in perovskite solar cells10.1002/aenm.201500279 ↗
48. The effect of the microstructure on trap‐assisted recombination and light soaking phenomenon in hybrid perovskite solar cells10.1002/adfm.201602519 ↗
49. Understanding the beneficial role of grain boundaries in polycrystalline solar cells from single‐grain‐boundary scanning probe microscopy10.1002/adfm.200500396 ↗
50. Investigating the role of grain boundaries in CZTS and CZTSSe thin film solar cells with scanning probe microscopy10.1002/adma.201103470 ↗
51. Evidence for ion migration in hybrid perovskite solar cells with minimal hysteresis10.1038/ncomms13831 ↗
52. Understanding the rate-dependent J–V hysteresis, slow time component, and aging in CH 3 NH 3 PbI 3 perovskite solar cells: the role of a compensated electric field10.1039/C4EE03664F ↗
53. Slow dynamic processes in lead halide perovskite solar cells. Characteristic times and hysteresis10.1021/jz5011187 ↗
54. Understanding detrimental and beneficial grain boundary effects in halide perovskites10.1002/adma.201804792 ↗
55. Impact of excess CH3NH3I on free carrier dynamics in high-performance nonstoichiometric perovskites10.1021/acs.jpcc.6b11984 ↗