journal article·2012-03

Comparison of metal oxides as anode buffer layer for small molecule organic photovoltaic cells

Mohsen Ghasemi Varnamkhasti, Hamid Reza Fallah, Mojtaba Mostajaboddavati, Rasool Ghasemi, Ali Hassanzadeh

Publisher page

Abstract

Abstract In this work, small molecule organic photovoltaic cells based on copper phthalocyanine (CuPc)/C60 hetrojunction were fabricated. To have a good band structure matching between the work function of the anode and the highest occupied molecular orbital of the organic material the introduction of a buffer layer is necessary. Efficiency of devices shows a strong improvement when the metal oxides such as molybdenum oxide (MoO3) and tungsten oxide (WO3) were used as buffer layer between the ITO anode and active layer. The effect of MoO3 and WO3 thickness on the performance of the photovoltaic devices was investigated and compared. The thickness of each buffer layer was optimized to have better hole transport. Also the devices' performance was analyzed based on the surface roughness of bare ITO, and ITO, which covered with WO3 and MoO3. It was found that the anode buffer layer thickness is a very important factor in controlling the electrical characteristics of the organic photovoltaic devices. It is shown that the best results are obtained with a 4 nm MoO3.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Molecular Junctions and Nanostructures

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. Roll-to-roll fabrication of monolithic large-area polymer solar cells free from indium-tin-oxide10.1016/j.solmat.2009.04.020 ↗
2. Upscaling of polymer solar cell fabrication using full roll-to-roll processing10.1039/b9nr00430k ↗
3. ITO-free flexible polymer solar cells: From small model devices to roll-to-roll processed large modules10.1016/j.orgel.2011.01.009 ↗
4. Fabrication and processing of polymer solar cells: a review of printing and coating techniques10.1016/j.solmat.2008.10.004 ↗
5. Stability/degradation of polymer solar cells10.1016/j.solmat.2008.01.005 ↗
6. The effect of post-processing treatments on inflection points in current–voltage curves of roll-to-roll processed polymer photovoltaics10.1016/j.solmat.2010.06.007 ↗
7. Low band gap polymers based on 1,4-dialkoxybenzene, thiophene, bithiophene donors and the benzothiadiazole acceptor10.1016/j.solmat.2009.12.023 ↗
8. Enhanced charge collection in polymer photovoltaic cells by using an ethanol-soluble conjugated polyfluorene as cathode buffer layer10.1016/j.solmat.2008.12.007 ↗
9. Organic solar cells employing magnetron sputtered p-type nickel oxide thin film as the anode buffer layer10.1016/j.solmat.2010.08.004 ↗
10. Organic photovoltaic cell employing organic heterojunction as buffer layer10.1016/j.tsf.2007.09.043 ↗
11. Influence of molecular architecture and intermixing on the photovoltaic, morphological and spectroscopic properties of CuPc–C60 heterojunctions10.1016/j.solmat.2004.02.027 ↗
12. Investigation into effects of electron transporting materials on organic solar cells with copper phthalocyanine/C60 heterojunctions10.1016/j.cplett.2006.05.010 ↗
13. Role of exciton blocking layers in improving efficiency of copper phthalocyanine based organic solar cells10.1016/j.jnoncrysol.2007.10.098 ↗
14. Influence of the exciton blocking layer on the stability of layered organic solar cells10.1016/j.jpcs.2010.11.006 ↗
15. Ultra thin metal layer passivation of the transparent conductive anode in organic solar cells10.1016/j.solmat.2008.06.016 ↗
16. Stability/degradation of polymer solar cells10.1016/j.solmat.2008.01.005 ↗
17. Durability of PEDOT:PSS-pentacene Schottky diode10.1088/0022-3727/41/1/012003 ↗
18. p-Type semiconducting nickel oxide as an efficiency-enhancing anode interfacial layer in polymer bulk-heterojunction solar cells10.1073/pnas.0711990105 ↗
19. An efficient triple-tandem polymer solar cell10.1109/LED.2009.2015686 ↗
20. Transition metal oxides as the buffer layer for polymer photovoltaic cells10.1063/1.2174093 ↗
21. Efficient bulk heterojunction photovoltaic cells using small-molecular-weight organic thin films10.1038/nature01949 ↗
22. Battery effects in organic photovoltaics based on polybithiophene10.1016/j.solmat.2007.09.018 ↗
23. Mixed donor–acceptor molecular heterojunctions for photovoltaic applications I. material properties
24. Simulation of light intensity dependent current characteristics of polymer solar cells10.1063/1.1646435 ↗
25. Charge transport and photocurrent generation in Poly(3-hexylthiophene): Methanofullerene bulk-heterojunction solar cells10.1002/adfm.200500420 ↗
26. MoO3 buffer layer effect on photovoltaic properties of interpenetrating heterojunction type organic solar cells10.1016/j.tsf.2009.07.044 ↗
27. Room-temperature fabrication of transparent flexible thin-film transistors using amorphous oxide semiconductors10.1038/nature03090 ↗