From spin coating to doctor blading: A systematic study on the photovoltaic performance of an isoindigo-based polymer
Source abstract
Abstract
Doctor blading is suitable to roll-to-roll process with much little solution wasting and is less studied compared with the mainstream spin coating. In this work, we used a novel polymer blended with two common fullerene derivatives as active solutions. To systemically understand the different coating methods and the different fullerene acceptors on the effect of polymer solar cells (PSCs) photovoltaic performance, the wet active solution physic-chemical properties and variations of the dried active layer characterizations were investigated. It was observed that it is much easier to obtain a homogeneous film from doctor blading compared with spin coating for the polymer: PC71BM solution due to the high surface tension and viscosity. Moreover, the high boiling point additive plays an important role in inhibiting the wet film shrinkage and forming a uniform film. The longer film drying time for the doctor-blading films leads to larger domains than spin coating, thus increases the geminate recombination and results in lower mobilities as well as power conversion efficiencies (PCE). Doctor-blading-processed PSCs with PCE of 4.46% were achieved for P3TI:PC71BM devices, which were comparable to those of spin-coating devices. This work provided valuable suggestions and solutions for the doctor-blading process, especially for crystalline D-A polymer-based devices.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Thin-Film Transistor Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Flexible ITO-free polymer solar cells10.1002/app.38854 ↗
2. Polymer solar cells10.1038/nphoton.2012.11 ↗
3. Simultaneous enhancement of open-circuit voltage, short-circuit current density, and fill factor in polymer solar cells10.1002/adma.201103006 ↗
4. Polymer solar cells with enhanced open-circuit voltage and efficiency10.1038/nphoton.2009.192 ↗
5. Polymer solar cell modules prepared using roll-to-roll methods: knife-over-edge coating, slot-die coating and screen printing10.1016/j.solmat.2008.12.012 ↗
6. Roll-to-roll fabrication of monolithic large-area polymer solar cells free from indium-tin-oxide10.1016/j.solmat.2009.04.020 ↗
7. Enhanced power-conversion efficiency in polymer solar cells using an inverted device structure10.1038/nphoton.2012.190 ↗
8. A polymer tandem solar cell with 10.6% power conversion efficiency10.1038/ncomms2411 ↗
9. Inkjet printing of organic electronics – comparison of deposition techniques and state-of-the-art developments10.1039/c2tc00255h ↗
10. Fabrication and processing of polymer solar cells: a review of printing and coating techniques10.1016/j.solmat.2008.10.004 ↗
11. Towards 15% energy conversion efficiency: a systematic study of the solution-processed organic tandem solar cells based on commercially available materials10.1039/c3ee42307g ↗
12. Performance analysis of printed bulk heterojunction solar cells10.1002/adfm.200500581 ↗
13. Printing highly efficient organic solar cells10.1021/nl801365k ↗
14. Polymer solar cell by blade coating10.1016/j.orgel.2009.03.001 ↗
15. Photovoltaic loss analysis of inkjet-printed polymer solar cells using pristine solvent formulations
16. An easily accessible isoindigo-based polymer for high-performance polymer solar cells10.1021/ja206610u ↗
17. Structure–property relationships of oligothiophene-isoindigo polymers for efficient bulk-heterojunction solar cells10.1039/C3EE42989J ↗
18. Roll-to-roll fabrication of large area functional organic materials10.1002/polb.23192 ↗
19. Fluid-dynamic properties and wetting behavior of coating inks for roll-to-roll production of polymer-based solar cells10.1007/s11998-013-9483-5 ↗
20. Quantification of quantum efficiency and energy losses in low bandgap polymer:fullerene solar cells with high open-circuit voltage10.1002/adfm.201200608 ↗
21. Influence of the processing solvent on the photoactive layer nanomorphology of P3HT/PC60BM solar cells10.1002/pola.25865 ↗
22. Comparison of large scale coating techniques for organic and hybrid films in polymer based solar cells10.1016/j.cep.2012.03.004 ↗
23. Estimation of the surface free energy of polymers10.1002/app.1969.070130815 ↗
24. Effect of substrate roughness on the apparent surface free energy of sputter deposited superhydrophobic polytetrafluoroethylene coatings: a comparison of experimental data with different theoretical models10.1063/1.3456165 ↗
25. Study on the surface energy of graphene by contact angle measurements10.1021/la5018328 ↗
26. Improving the nanoscale morphology and processibility for PCDTBT-based polymer solar cells via solvent mixtures10.1016/j.orgel.2012.08.003 ↗
27. An easily synthesized blue polymer for high-performance polymer solar cells10.1002/adma.201002225 ↗
28. Aqueous processing of low-band-gap polymer solar cells using roll-to-roll methods10.1021/nn200933r ↗
29. Control of the active layer nanomorphology by using co-additives towards high-performance bulk heterojunction solar cells10.1016/j.orgel.2012.05.001 ↗
30. 23% Enhanced efficiency of polymer solar cells processed with 1-chloronaphthalene as the solvent additive10.1016/j.synthmet.2012.12.016 ↗
31. Influence of processing additives to nano-morphology and efficiency of bulk-heterojunction solar cells: a comparative review10.1016/j.solener.2010.10.012 ↗
32. All polymer photovoltaics: from small inverted devices to large roll-to-roll coated and printed solar cells10.1016/j.solmat.2013.01.025 ↗
33. A facile route to polymer solar cells with optimum morphology readily applicable to a roll-to-roll process without sacrificing high device performance10.1002/adma.201000250 ↗
34. Recent advances in solution-processed interfacial materials for efficient and stable polymer solar cells
35. Technology development for roll-to-roll production of organic photovoltaics10.1016/j.cep.2010.07.012 ↗
36. Lateral phase separation gradients in spin-coated thin films of high-performance polymer: fullerene photovoltaic blends10.1002/adfm.201100566 ↗
37. Conformational disorder enhances solubility and photovoltaic performance of a thiophene-quinoxaline copolymer10.1002/aenm.201201019 ↗
38. Polymeric solar cells based on P3HT:PCBM: role of the casting solvent10.1016/j.solmat.2011.07.039 ↗
39. Moving through the phase diagram: morphology formation in solution cast polymer-fullerene blend films for organic solar cells10.1021/nn2036279 ↗
40. The development of nanoscale morphology in polymer: fullerene photovoltaic blends during solvent casting10.1039/c0sm00343c ↗
41. In situ reflectance imaging of organic thin film formation from solution deposition10.1016/j.solmat.2013.02.030 ↗
42. Organic photovoltaics with thick active layers (similar to 800nm) using a high mobility polymer donor10.1016/j.solmat.2013.02.033 ↗
43. Efficient small bandgap polymer solar cells with high fill factors for 300nm thick films10.1002/adma.201300017 ↗
44. In situ monitoring the drying kinetics of knife coated polymer-fullerene films for organic solar cells10.1063/1.3270402 ↗
45. In situ X-Ray study of drying-temperature influence on the structural evolution of bulk-heterojunction polymer-fullerene solar cells processed by doctor-blading10.1002/aenm.201100007 ↗
46. Polymer solar cells with enhanced fill factors10.1038/nphoton.2013.207 ↗