Modeling and testing the mechanical strength of solar cells
Source abstract
Abstract
Abstract The strength and fracture behavior of solar cells govern the failure of cells in a photovoltaic module under thermal and mechanical loads. In this study, the testing and modeling of strength of silicon solar cells with aluminium metallization are presented. Therefore, the contribution of microstructure in solar cells was analyzed regarding stiffness and fracture behavior. With this knowledge, a simulation model was created to evaluate the influence of each layer to the stress field inside the silicon part of the solar cell. The model was used to evaluate 4-point bending experiments, which were performed to determine the strength of solar cells on front and backside and in two different directions, parallel and perpendicular to the busbars. It is shown that the strength and breakage depend strongly on the side and direction of loading. The lowest strength was detected for the backside being loaded with tensile stress parallel to the busbars.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · Advanced ceramic materials synthesis · Graphite, nuclear technology, radiation studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Systematic investigation of cracks in encapsulated solar cells after mechanical loading10.1016/j.solmat.2012.12.031 ↗
2. Spatial and orientational distribution of cracks in crystalline photovoltaic modules generated by mechanical load tests10.1016/j.solmat.2011.06.032 ↗
3. The risk of power loss in crystalline silicon based photovoltaic modules due to micro-cracks10.1016/j.solmat.2010.10.034 ↗
4. K. Wasmer, A. Bidiville, F. Jeanneret, J. Michler, C. Ballif, M. van der Meer, P. Nasch, Effects of edge defects induced by multi-wire sawing on the wafer strength, in: 23rd European Photovoltaic Solar Energy Conference and Exhibition, pp. 1305–1310.
5. A. Bohne, S. Schoenfelder, J. Bagdahn, The influence of wire sawing process on mono- and multicrystalline silicon wafers, in: 23rd European Photovoltaic Solar Energy Conference.
6. Challenges of the wire saw wafering process
7. A. Grün, A. Lawerenz, R. Porytskyy, O. Anspach, Investigation of wafer surfaces with space-resolved breaking strength tests and corresponding analysis of the crack depth, in: 26th European Photovoltaic Solar Energy Conference.
8. Mechanical strength of silicon wafers cut by loose abrasive slurry and fixed abrasive diamond wire sawing10.1002/adem.201100263 ↗
9. A. Grün, K. Lauer, R. Porytskyy, Methods for investigating the subsurface damage at bevel polished wafer samples, in: 27th European Photvoltaic Solar Energy Conference and Exhibition, pp. 1014–1017.
10. C. Kohn, R. Kuebler, M. Krappitz, G. Kleer, I. Reis, M. Retzlaff, D. Erath, D. Biro, Influence of the metallization process on the strength of silicon solar cells, in: 24th European Photovoltaic Solar Energy Conference.
11. C. Kohn, R.M. Hug, Kübler, M. Krappitz, G. Kleer, Increase of the strength of screen printed silicon solar cells by post treatments, in: 25th European Photovoltaic Solar Energy Conference, pp. 2062–2065.
12. Breakage issues in silicon solar wafers and cells
13. V. Popovich, M. Janssen, I. Richardson, T. van Amstel, I.J. Bennett, Microstructure and mechanical properties of aluminum back contact layers, in: 24th European Photovoltaic Solar Energy Conference, pp. 1453–1458.10.1016/j.solmat.2010.04.037 ↗
14. T. van Amstel, V. Popovich, I. Bennett, A multiscale model of the aluminium layer at the rear side of a solar cell, in: 24th European Photovoltaic Solar Energy Conference, pp. 1179–1185.
15. S. Schoenfelder, A. Bohne, J. Bagdahn, Comparison of test methods for strength characterization of thin solar wafer, in: 22nd European Photovoltaic Solar Energy Conference, pp. 1636–1640.
16. Weibull · 1939
17. A statistical distribution function of wide applicability10.1115/1.4010337 ↗
18. STANDARD ASTM C 1239-07, Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics, 2007.
19. STANDARD DIN EN 843–5:2007-03, Hochleistungskeramik – Mechanische Eigenschaften monolithischer Keramik bei Raumtemperatur – Teil 5: Statistische Auswertung, DIN, 2007.
20. Microstructural and electrical properties of different-sized aluminum-alloyed contacts and their layer system on silicon surfaces10.1016/j.solmat.2011.03.017 ↗
21. V. Popovich, N. van der Pers, M. Janssen, I. Bennett, K. Jansen, J. Wright, I. Richardson, Residual and bending stress measurements by x-ray diffraction and synchrotron diffraction analysis in silicon solar cells, in: 38th IEEE Photovoltaic Specialists Conference (PVSC), 2012, pp. 000442–000447.10.1109/PVSC.2012.6317653 ↗
22. Homogenization methods for multi-phase elastic composites with non-elliptical reinforcements10.1016/j.euromechsol.2011.12.002 ↗
23. M. Pander, Mechanische Untersuchungen an Solarzellen in PV-Modulen mittels Finite-Elemente-Modellierung, Master's Thesis, Hochschule für Technik, Wirtschaft und Kultur Leipzig (FH), 2009.
24. C. Kohn, T. Faber, R. Kübler, J. Beinert, G. Kleer, F. Clement, D. Erath, I. Reis, F. Martin, A. Müller, Analyses of warpage effects induced by passivation and electrode coatings in silicon solar cells, in: 22nd European Photovoltaic Solar Energy Conference and Exhibition.
25. Electronic effects in the elastic constants of n-type silicon10.1103/PhysRev.161.756 ↗