journal article·2020-01-01Open access

Alternative of bone china and porcelain as ceramic hand molds for rubber latex glove films formation via dipping process

Chaturaphat Tharasana, Aniruj Wongaunjai, Puwitoo Sornsanee, Vichasharn Jitprarop, Nuchnapa Tangboriboon

Abstract

Abstract In general, the main compositions of porcelain and bone china composed of 54-65%wt silica (SiO2), 23-34% wt alumina (Al2O3) and 0.2-0.7%wt calcium oxide (CaO) suitable for preparation high quality ceramic products such as soft-hard porcelain products for teeth and bones, bioceramics, IC substrate and magneto-optoelectroceramics. The quality of ceramic hand mold is depended on raw material and its properties (pH, ionic strength, solid-liquid surface tension, particle size distribution, specific surface area, porosity, density, microstructure, weight ratio between solid and water, drying time, and firing temperatures). The suitable firing conditions for porcelain and bone china hand-mold preparation were firing at 1270°C for 10 h which resulted in superior working molds for making latex films from natural and synthetic rubber. The obtained fired porcelain hand molds at 1270°C for 10 h provided good chemical durability (10%NaOH, 5%HCl and 10%wtNaCl), low thermal expansion coefficient (5.8570 × 10−6(°C−1)), good compressive (179.40 MPa) and good flexural strength (86 MPa). While thermal expansion coefficient, compressive and flexural strength of obtained fired bone china hand molds are equal to 6.9230 × 10−6(°C−1), 128.40 and 73.70 MPa, respectively, good acid-base-salt resistance, a smooth mold surface, and easy hand mold fabrication. Both obtained porcelain and bone china hand molds are a low production cost, making them suitable for natural and synthetic rubber latex glove formation.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Dental materials and restorations · Bone Tissue Engineering Materials · Recycling and utilization of industrial and municipal waste in materials production

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Materials Engineering Department, Faculty of Engineering , Kasetsart University , Bangkok 10900 , Thailand

Materials Engineering Department, Faculty of Engineering , Kasetsart University , Bangkok 10900 , Thailand ; Tel.: 66-2-797-0999-2106; Fax: 66-2-955-1811

References (42)

Show source-provided references
1. [1] Thakur, V. K., S. A. Singha, and M. K. Thakur. Graft copolymerization of methyl graft copolymerization of methyl acrylate onto cellulosic biofibers: synthesis, characterization and applications. Journal of Polymers and the Environmental, Vol. 20, No.1, 2012, pp. 164-174.10.1007/s10924-011-0372-710.1007/s10924-011-0372-7 ↗
2. [2] Singha, A. S., and V. K. Thakur. Synthesis and characterization of Grewia optiva fiber reinforced PF matrix based polymer composites. International Journal of Polymeric Materials, Vol. 57, 2008, pp. 1059-1074.10.1080/0091403080225780010.1080/00914030802257800 ↗
3. [3] Singha, A.S., and V. K. Thakur. Mechanical, morphological and thermal properties of pine needles reinforced polymer composites. International Journal of Polymeric Materials, Vol. 58, 2009, pp. 217-228.10.1080/0091403080246185710.1080/00914030802461857 ↗
4. [4] Thakur, V. K., A. S. Singha, I. Kaur, R. P. Nagarajarao, Y. and Liping. Silane functionalization of saccaharum cilliare fibers: Thernal, morphological, and physicochemical study. International Journal of Polymer Analysis Characterization, Vol. 15, 2010, pp. 397-414.10.1080/1023666X.2010.51010610.1080/1023666X.2010.510106 ↗
5. [5] Njoya, D., M. Hajjaji, and D. Njopwouo. Effects of some processing factors on technical properties of a clay-based ceramic material. Applied Clay Science, Vol. 65-66, 2012, pp. 106-113.10.1016/j.clay.2012.05.01310.1016/j.clay.2012.05.013 ↗
6. [6] Singh, M., J. Esquena, C. Solans, K. Booten, and T. F. Tadros. Influence of hydrophobically modified inulin (INUTEC NRA) on the stability of vulcanized natural rubber latex. Colloid and Surface A, Vol. 451, 2014, pp. 90-100.10.1016/j.colsurfa.2014.03.05710.1016/j.colsurfa.2014.03.057 ↗
7. [7] Mao, H., M. Hillert, M. Selleby, and B. Sundman. Thermodynamic assessment of the CaO-Al2O3-SiO2 Systems. Journal of American Ceramic Society, Vol. 89, No. 1, 2006, pp. 298-308.10.1111/j.1551-2916.2005.00698.x10.1111/j.1551-2916.2005.00698.x ↗
8. [8] Husain, S.A. Modelling the viscoelasticity of porous ceramics. International Conference on environment and Industrial Innovation, Vol. 12, 2011, pp. 221-223.
9. [9] Cacioli, P. Introduction to latex and the rubber Industry. Revue francaise d’allergologie, Vol. 37, No.8, 1997, pp. 1173-1176.10.1016/S0335-7457(97)80146-310.1016/S0335-7457(97)80146-3 ↗
10. [10] Steward, P. A., J. Hearn, and M. C. Wilkinson. An overview of polymer latex film formation and properties. Advances in Colloid and Interface Science., Vol. 86, No. 3, 2000, pp. 195-267.10.1016/S0001-8686(99)00037-810.1016/S0001-8686(99)00037-8 ↗
11. [11] Charmeau, J. Y., R. Berthet, C. Gringreau, Y. Holl, and E. Kientz. Effects of film structure on mechanical and adhesion properties of latex films. International Journal of Adhesion and Adhesive, Vol.17, 1997, pp. 169-176.10.1016/S0143-7496(96)00034-610.1016/S0143-7496(96)00034-6 ↗
12. [12] Keddie, J. L. Film formation of latex. Materials Science and Engineering R., Vol. 21, 1997, pp. 101-170.10.1016/S0927-796X(97)00011-910.1016/S0927-796X(97)00011-9 ↗
13. [13] Yeang, H. Y., and F. Yusof. Latex allergy studies: Differential leaching of soluble proteins from the inner and outer surfaces of natural rubber latex examination gloves. Journal of Rubber Research, Vol. 8, No. 2, 1993, pp. 154-161.
14. [14] Callister, W. D. Materials science and engineering: An introduction. John Wiley & Sons, 9th Ed., 2018, 806 pp.
15. [15] Çencel, Y. A. Heat and mass transfer, a practical approach. McGraw-Hil, 2006, 879 pp.
16. [16] Tangboriboon, N., S. Pakdeeniti, R. Kunanuraksapong, and A. Sirivat. Calcium silicate (CaSiO3) as alternative ionic coagulant and solid lubricant for ceramic molds in natural rubber latex film preparation. Rubber Chemistry Technology, Vol. 85, No. 4, 2012, pp. 645-660.10.5254/rct.12.8892310.5254/rct.12.88923 ↗
17. [17] Tangboriboon, N., P. Phudkrachang, R. Kunanuraksapong, and A. Sirivat. Removing extractable proteins in natural rubber latex by calcium chloride from chicken eggshells. Rubber Chemistry Technology, Vol. 84, No. 4, 2011, pp. 543-564.10.5254/1.361453010.5254/1.3614530 ↗
18. [18] Tsai, W. T., J. M. Yang, C. W. Lai, Y. H. Cheng, C. C. Lin, and C. W. Yeh. Characterization and adsorption properties of eggshells and eggshell membrane. Bioresource Technology, Vol. 97, 2006, pp. 488-493.10.1016/j.biortech.2005.02.05010.1016/j.biortech.2005.02.050 ↗
19. [19] Tangboriboon, N., S. Pornsimma, and A. Sirivat. Embedding eggshell as flux in porcelain clay products to reduce firing temperature via extrusion process. Middle East Journal of Scientific Research, Vol. 24, No. 5, 2016, pp. 1616-1621.
20. [20] Tangboriboon, N., P. Phudkrachang, S. Kasemsumran, R. Kunanuraksapong, and A. Sirivat. An innovative measurement of extractable proteins from concentrated latex containing eggshell calcium oxide compounds by near-infrared spectroscopy. Spectroscopy Letters, Vol. 45, 2012, pp. 29-39.10.1080/00387010.2011.59084310.1080/00387010.2011.590843 ↗
21. [21] Soontorntepwarakul, N., N. Wangrungroj, and N. Tangboriboon. Adsorption of biocellulose nanofiber tissue engineering from acetobacter xylinum (acetobacteraceae) embedded eggshell membrane via fermentation process. Modern Applied Science, Vol. 13, No. 10, 2019, pp. 11-25.10.5539/mas.v13n10p1110.5539/mas.v13n10p11 ↗
22. [22] Tangboriboon, N., R. Takkire, W. Sangwan, S. Changkhamchom, and A. Sirivat. Bio-CaCO3 from raw eggshell as additive in natural rubber latex glove film. Rubber Chemistry and Technology, Vol. 92, No. 3, 2019, pp. 558-577.10.5254/rct.19.8148910.5254/rct.19.81489 ↗
23. [23] ASTM C165-95 Standard test method for measuring compressive properties of thermal insulations. Available from: https://www.astm.org/DATABASE.CART/HISTORICAL/C165-95.htm.
24. [24] ASTM D790-03 Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating materials. Available from: https://www.astm.org/DATABASE.CART/HISTORICAL/D790-03.htm.
25. [25] ASTM C518 Standard test methods for flexural properties of un-reinforced and reinforced plastics and electrical insulating materials.
26. [26] ASTM B212 Standard test method for apparent density of free-flowing metal powders using the hall flowmeter funnel. Available from: https://www.astm.org/Standards/B212.htm.
27. [27] ASTM C373 Standard test methods for determination of water absorption and associated properties by vacuum method for pressed ceramic tiles and glass tiles and boil method for extruded ceramic tiles and non-tile fired ceramic whiteware products. Available from: https://www.astm.org/Standards/C373.htm.
28. [28] Sokolar, R. Sintering of whiteware body depending on different fluxing agents and binders. Intech, 2018, DOI: http://dx.doi.org/10.5772/68082.10.5772/6808210.5772/68082 ↗
29. [29] Kitouni, S., and A. Harabi. Sintering and mechanical properties of porcelains prepared from Algerian raw materials. Cerâmica, Vol. 57, 2011, pp. 453-460.10.1590/S0366-6913201100040001310.1590/S0366-69132011000400013 ↗
30. [30] Tobudare, T. S., S. S. Owoeya, A. Kenneth-Emehige, and O. E. Isinkaye. Microstructure evolution and physico-mechanical properties of bone china porcelain compositions using two selected kaolinite clays from Nigeria. Scientific Africa, Vol. 3, 2019, pp.1-8.10.1016/j.sciaf.2019.e0006610.1016/j.sciaf.2019.e00066 ↗
31. [31] Piccinini, C. A., S. R. Bragança, and C. P. Bergmann. Method for the characterization of electrophoretic properties of clay slips. Applied Clay Science, Vol. 86, 2013, pp. 11-17.10.1016/j.clay.2013.10.00310.1016/j.clay.2013.10.003 ↗
32. [32] Zheng, J. P., L. Luan, H. Y. Wang, L. F. Xi, K. D. Yao. Study on ibuprofen/montmorillo- nite. Applied Clay Science, Vol. 36, 2007, pp. 297-301.10.1016/j.clay.2007.01.01210.1016/j.clay.2007.01.012 ↗
33. [33] Carretero, M. I. Clay minerals and their beneficial effects upon human health. A review. Applied Clay Science, Vol. 21, 2002, pp. 155-163.10.1016/S0169-1317(01)00085-010.1016/S0169-1317(01)00085-0 ↗
34. [34] Obada, D. O., D. Dodoo-Arhin, M. Dauda, F. O. Anafi, A. S. Ahmed, and O. A. Ajayi. Physico-mechanical and gas permeability characteristics of kaolin based ceramic membranes prepared with a new pore-forming agent. Applied Clay Science, Vol. 150, 2017, pp. 175-183.10.1016/j.clay.2017.09.01410.1016/j.clay.2017.09.014 ↗
35. [35] Singh, M., S. F. M. Sharib. K. L. Mok, and A. H. M. Yatim. Colloidal properties of precipitated calcium carbonate dispersion and its effect on prevulcanised natural rubber latex rheology and film tensile properties. Journal of Rubber Research, Vol. 22, 2019, pp. 43-57.10.1007/s42464-019-00009-810.1007/s42464-019-00009-8 ↗
36. [36] Hunter, R. J. Chapter 6 - Applications of the zeta potential. In Potential in colloid science. Principles and applications. 1981, pp. 219-257.10.1016/B978-0-12-361961-7.50010-910.1016/B978-0-12-361961-7.50010-9 ↗
37. [37] Beketova, A., S. Varitis, E. Kontonasaki, T. Zorba, L. Papadopoulou, N. Kantiranis, et al. Evaluation of the micro-mechanical and bioactive properties of bioactiveglass-dental porcelain composite. Journal of the Mechanical Behavior of Biomedical Materials, Vol. 86, 2018, pp. 77-83.10.1016/j.jmbbm.2018.06.01910.1016/j.jmbbm.2018.06.019 ↗
38. [38] Lenza, R. F. S., and W. L. Vasconcelos. Preparation of silica by sol-gel method using formamide. Materials Research, Vol. 4, No. 3, 2001, pp. 189-194.10.1590/S1516-1439200100030000810.1590/S1516-14392001000300008 ↗
39. [39] Aguiar, H., J. Serra, P. González, and B. León. Structural study of sol–gel silicate glasses by IR and Raman spectroscopies. Journal of Non-Crystalline Solids, Vol. 355, 2009, pp. 475-480.10.1016/j.jnoncrysol.2009.01.01010.1016/j.jnoncrysol.2009.01.010 ↗
40. [40] Sokolář, R., L. Keršnerová, and M. Šveda. The effect of different fluxing agents on the sintering of dry pressed porcelain bodies. Journal of Asian Ceramic Societies, Vol. 5, No. 3, 2017, pp. 290-294.10.1016/j.jascer.2017.06.00110.1016/j.jascer.2017.06.001 ↗
41. [41] Reed, J. S. Introduction to the Principles of Ceramic Processing. John Wiley & Sons, New York, 1989.
42. [42] Alger, M. Polymer Science Dictionary. Chapman & Hall, 2nd Ed., 1997, 628 pp.