Effect of annealing-induced oxidation of molybdenum oxide on organic photovoltaic device performance
Source abstract
Abstract
Abstract Molybdenum oxide (MoO x ) has been widely used as a hole transport layer in organic photovoltaic cells (OPVs), whose performance can be improved by inserting a MoO x layer between an organic active layer and a transparent anode because of efficient carrier dissociation. In this study, the influence of thermally annealed MoO x on the photovoltaic performance of OPVs was first investigated using low-bandgap polymer and [6,6]-phenyl C 71 -butyric acid methyl ester (PC 71 BM) blend films as the active layer. We used three low-bandgap polymers: poly[2,6-(4,4-bis-(2-ethylhexyl)-4 H -cyclopenta[2,1- b ;3,4- b ′]dithiophene)- alt -4,7(2,1,3-benzothiadiazole)] (PCPDTBT), poly(4,8-bis[(2-ethylhexyl)oxy]benzo[1,2- b :4,5- b ′]dithiophene-2,6-diyl3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl) (PTB7), and poly([2,6′-4,8-di(5-ethylhexylthienyl)benzo[1,2-b,3,3-b]dithiophene]3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl) (PTB7-Th). Power conversion efficiencies were drastically increased for all investigated polymers when the as-deposited MoO x layer was annealed at 160 °C for 5 min. In particular, a high efficiency of 6.57% was achieved when PTB7 was used; for comparison, the efficiency of a reference device with an as-deposited MoO x layer (not subjected to annealing) was 1.40%. Specifically, the short-circuit current density and fill factor were remarkably improved after annealing, which means that efficient carrier dissociation was achieved in the active layer. We evaluated optical absorption and surface morphology to elucidate reasons behind the improved photovoltaic performance, and these parameters only slightly changed after annealing. In contrast, angle-dependent X-ray photoelectron spectroscopy revealed that the MoO x layer was oxidized after annealing. In general, the oxygen vacancies of MoO x act as carrier traps; a reduction in the number of carrier traps causes high hole mobility in the organic layer, which, in turn, results in an improved photovoltaic performance. Therefore, our results indicate that the annealing-induced oxidation of MoO x is useful for achieving high photovoltaic performance.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Perovskite Materials and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. 10.2% Power conversion efficiency polymer tandem solar cells consisting of two identical sub-cells10.1002/adma.201300964 ↗
2. An efficient triple-junction polymer solar cell having a power conversion efficiency exceeding 11%10.1002/adma.201402072 ↗
3. Efficient inverted polymer solar cells employing favourable molecular orientation10.1038/nphoton.2015.84 ↗
4. Solution-processable polymeric solar cells: a review on materials, strategies and cell architectures to overcome 10%10.1016/j.orgel.2015.01.014 ↗
5. Recent progress in metal-organic complexes for optoelectronic applications10.1039/C3CS60449G ↗
6. High-mobility organic thin-film transistors based on a small-molecule semiconductor deposited in vacuum and by solution shearing10.1016/j.orgel.2013.09.003 ↗
7. Efficiency enhancement in low-bandgap polymer solar cells by processing with alkane dithiols10.1038/nmat1928 ↗
8. Enhanced power-conversion efficiency in polymer solar cells using an inverted device structure10.1038/nphoton.2012.190 ↗
9. Single-junction polymer solar cells with high efficiency and photovoltage10.1038/nphoton.2015.6 ↗
10. Molecular materials for organic photovoltaics: small is beautiful10.1002/adma.201305999 ↗
11. 25th anniversary article: a decade of organic/polymeric photovoltaic research10.1002/adma.201302563 ↗
12. Fabrication and processing of polymer solar cells: a review of printing and coating techniques10.1016/j.solmat.2008.10.004 ↗
13. A nonionic surfactant simultaneously enhancing wetting property and electrical conductivity of PEDOT: PSS for vacuum-free organic solar cells10.1016/j.solmat.2015.02.024 ↗
14. Photovoltaic analysis of the effects of PEDOT: PSS-additives hole selective contacts on the efficiency and lifetime performance of inverted organic solar cells10.1016/j.solmat.2014.10.004 ↗
15. Recombination and loss analysis in polythiophene based bulk heterojunction photodetectors10.1063/1.1521244 ↗
16. Degradation of organic solar cells due to air exposure10.1016/j.solmat.2006.06.041 ↗
17. Direct observation of hole accumulation in polymer solar cells during device operation using light-induced electron spin resonance10.1002/adma.201204015 ↗
18. Highly efficient and stable solar cells based on thiazolothiazole and naphthobisthiadiazole copolymers10.1038/srep14202 ↗
19. Preparation and characterization of MoO3 hole-injection layer for organic solar cell fabrication and optimization10.1016/j.solmat.2013.10.002 ↗
20. Improving performance of organic solar cells using amorphous tungstenoxides as an interfacial buffer layer on transparent anodes10.1016/j.orgel.2009.03.016 ↗
21. Effect of buffer layers on stability of polymer-based organic solar cells10.1143/JJAP.49.01AC02 ↗
22. Efficient, air-stable bulk heterojunction polymer solar cells using moox as the anode interfacial layer10.1002/adma.201100038 ↗
23. Solvent-treated PEDOT: PSS on the improvement PTB7 based on polymer solar cells performance10.1016/j.apsusc.2015.06.160 ↗
24. Transition metal oxides as the buffer layer for polymer photovoltaic cells10.1063/1.2174093 ↗
25. Effect of molybdenum oxide electronic structure on organic photovoltaic device performance: an x-ray absorption spectroscopy study10.1021/jp508972v ↗
26. Processing additives for improved efficiency from bulk hetero junction solar cells10.1021/ja710079w ↗
27. Side chain selection for designing highly efficient photovoltaic polymers with 2D-conjugated structure10.1021/ma500829r ↗
28. For the bright future–bulk heterojunction polymer solar cells with power conversion efficiency of 7.4%10.1002/adma.200903528 ↗
29. Microstructured porous ZnO thin film for increased light scattering and improved efficiency in inverted organic photovoltaics10.1364/OE.22.0A1412 ↗
30. The effect of surface hydrogenation of metal oxides on the nanomorphology and the charge generation efficiency of polymer blend solar cells10.1039/C4NR04408H ↗
31. Low-temperature MoO3 film from a facile synthetic route for an efficient anode interfacial layer in organic optoelectronic devices10.1039/C3TC31580K ↗
32. Room-temperature, characterization and stability of electrochromic MoO3 thin films prepared by electrodeposition10.1149/1.2050004 ↗
33. Angle-resolved XPS: a critical evaluation for various applications10.1002/sia.2216 ↗
34. The important role of oxygen vacancies in Sr2MgSi2O7 phosphor10.1016/j.physleta.2016.01.001 ↗
35. Time-dependent formation of oxygen vacancies in black TiO2 nanotube arrays and the effect on photoelectrocatalytic and photoelectrochemical properties
36. Properties of interlayer for organic photovoltaics10.1016/j.mattod.2013.10.001 ↗
37. Space charge limited current measurements on conjugated polymer films using conductive atomic force microscopy10.1021/nl080155l ↗
38. Voltage-dependent photocurrent transients of PTB7:PC70BM solar cells: experiment and numerical simulation10.1063/1.4813612 ↗
39. Charge carrier mobility of the organic photovoltaic materials PTB7 and PC71BM and its influence on device performance10.1016/j.orgel.2015.03.013 ↗
40. Nguyen · Energy Environ. Sci. · 2014 · 7 · 304010.1039/C4EE01529K ↗