Controlled donor-accepter ratio for application of organic photovoltaic cells by alternative intermittent electrospray co-deposition
Source abstract
Abstract
Abstract Because co-deposition method has been utilized in a conventional thermal evaporation process to realize graded donor-acceptor architectures, we investigated an alternative intermittent electrospray co-deposition method for solution-processed organic photovoltaic cells. In this method, two solutions of poly(3-hexylthiophene-2,5-diyl) (P3HT) and phenyl-C61 butyric acid methyl ester (PCBM) were alternatively deposited using high-voltage pulse. Thus, the P3HT:PCBM blend thin film could be deposited even in a vacuum-free experimental setup. The optimum pulse width was found to be greater than 6 s to avoid an unexpected charge to the adjacent glass capillary, which causes the instable electrospray. The P3HT molecular ordering estimated from Raman spectroscopy and grazing incidence X-ray diffraction patterns was comparable to that estimated from the spin-coated device. In addition, the P3HT:PCBM ratio of the deposited thin film could be controlled by changing the ratio of the pulse width for the P3HT and PCBM solutions and was evaluated from the ultraviolet–visible absorption spectrum. Finally, a two layered bulk heterojunction structure with P3HT:PCBM was successfully demonstrated, leading to a maximum photoconversion efficiency of 3.1%. This value was 1.4-fold higher than that of the uniformly mixed bulk heterojunction device because of the high carrier-collection efficiency.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electrohydrodynamics and Fluid Dynamics · Organic Electronics and Photovoltaics · Carbon Nanotubes in Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. Solution-processable polymeric solar cells: a review on materials, strategies and cell architectures to overcome 10%10.1016/j.orgel.2015.01.014 ↗
2. Molecular materials for organic photovoltaics: small is beautiful10.1002/adma.201305999 ↗
3. Effect of Danköler number of evaporation on the morphology of active layer and the performance of organic heterojunction solar cells fabricated by electrospray method10.1016/j.solmat.2014.11.029 ↗
4. Influence of processing additives to nano-morphology and efficiency of bulk-heterojunction solar cells: a comparative review10.1016/j.solener.2010.10.012 ↗
5. Efficient inverted polymer solar cells employing favorable molecular orientation10.1038/nphoton.2015.84 ↗
6. Small molecular weight organic thin-film photodetectors and solar cells10.1063/1.1534621 ↗
7. Graded donor-acceptor heterojunctions for efficient organic photovoltaic cells10.1002/adma.201002454 ↗
8. Enhanced vertical concentration gradient in rubbed P3HT: PCBM graded bilayer solar cells10.1021/jz300710a ↗
9. Solution-processable polymer based photovoltaic devices with concentration graded bilayers made via composition control of a poly(3-hexylthiophene)/[6,6]-phenyl C61-butyric acidmethyl ester
10. Roll-to-roll fabrication of large area functional organic materials10.1002/polb.23192 ↗
11. Realization of solution processed multi-layer bulk heterojunction organic solar cells by electro-spray deposition10.1016/j.orgel.2012.06.016 ↗
12. Insertion of fullerene layer for bulk heterojunction organic photovoltaic cell fabricated by electrospray deposition method10.1002/pssr.201308167 ↗
13. Electrospray with electrostatic precipitator enhances fin particles collection efficiency10.1016/j.elstat.2010.03.002 ↗
14. Electrospraying route to nanotechnology: an overview10.1016/j.elstat.2007.10.001 ↗
15. Revision of capillary cone-jet physics: electrospray and flow focusing10.1103/PhysRevE.79.066305 ↗
16. Thin-film fabrication method for organic light-emitting diodes using electrospray deposition10.1002/adma.200900444 ↗
17. Surface morphology of fluorene thin film fabricated by electrospray deposition technique using two organic solvents: application for organic light-emitting diodes10.1016/j.tsf.2011.07.048 ↗
18. Multi-layered organic light-emitting diode fabrication using low molecular weight materials by electrospray method10.1016/j.tsf.2013.07.083 ↗
19. Mask-less patterning of organic light emitting diodes using electrospray and selective biasing on pixel electrodes10.1063/1.4919382 ↗
20. Fabrication of n- and p-channel step-edge vertical-channel transistors by electrospray deposition10.7567/JJAP.53.01AB16 ↗
21. Electrospray-processed soluble acenes toward the realization of high-performance field-effect transistors10.1021/am508162m ↗
22. Enhancement of the performance of organic solar cells by electrospray deposition with optimal solvent system10.1016/j.solmat.2013.10.020 ↗
23. Performance optimization of polymer solar cells using electrostatically sprayed photoactive layers10.1002/adfm.201000433 ↗
24. Variability of physical characteristics of electro-sprayed poly(3-hexylthiophene) thin film10.1063/1.3633519 ↗
25. An application of ESD technology for the R2R printing process10.1007/s12206-009-1148-z ↗
26. Characterization of deposition patterns produced by twin-nozzle electrospray10.1016/j.jaerosci.2008.05.003 ↗
27. Improved power conversion efficiency of organic photovoltaic cell fabricated by electrospray deposition method by mixing different solvents10.1143/JJAP.51.02BK12 ↗
28. Current and droplet size in the electrospray of liquids. Scaling laws10.1016/S0021-8502(96)00433-8 ↗
29. Influence of spray conditions on droplet charge per unit volume for electrospray deposition10.1016/j.jaerosci.2014.07.006 ↗
30. Absorption spectra modification in poly(3-hexylthiophene):methanofullerene blend thin films10.1016/j.cplett.2005.06.027 ↗
31. The nature of in-plane skeleton Raman modes of P3HT and their correlation to the degree of molecular order in P3HT: PCBM blend thin films10.1021/ja2013104 ↗
32. Resonance chemical imaging of polythiophene/fullerene photovoltaic thin films: mapping morphology-dependent aggregated and unaggregated C=C Species10.1021/ja900636z ↗
33. Drain current in poly(3-hexylthiophene) solutions during film formation: correlations to structural changes
34. High crystallinity parameter poly(3-hexylthiophene-2,5-diyl) thin film fabricated by electrospray deposition method10.1016/j.tsf.2013.08.019 ↗
35. Dynamics of crystallization and disorder during annealing P3HT/PCBM bulk heterojunctions10.1021/ma102817z ↗
36. Quantitative determination of organic semiconductor microstructure from the molecular to device scale10.1021/cr3001109 ↗
37. Correlating the scattered intensities of P3HT and PCBM to the current densities of polymer solar cells10.1039/C0CC02927K ↗