journal article·2014-11

Processing additive suppresses phase separation in the active layer of organic photovoltaics based on naphthalene diimide

Zhenghao Mao, Thinh P. Le, Kiarash Vakhshouri, Roshan Fernando, Fei Ruan, Evan Muller, Enrique D. Gomez, Geneviève Sauvé

Organic Electronics· Volume 15· Issue 11
Publisher page

Abstract

Abstract The development of non-fullerene electron acceptors for organic photovoltaics is gaining interest, as they offer the promise to overcome the light harvesting and energy tunability limitations of fullerenes. However, to fully take advantage of alternative acceptors, we must identify and achieve the needed morphologies within the active layer to maximize device performance. Here we demonstrate that the microstructure in the active layer of optimized poly(3-hexylthiophene)/naphthalene diimide devices resembles that of poly(3-hexylthiophene)/fullerene mixtures. Previously, we have reported on the synthesis of 2,6-dialkylaminonaphthalene diimides and found that the best performance was obtained with N,N′-di((thiophen-2-yl)methyl)-2,6-di(N-cyclohexylamino)-1,4,5,8-naphthalenetetracarboxydiimide (RF1). In this article, we show that suppressing the crystallization of both the donor and acceptor through the addition of 0.2% 1,8-diiodooctane (DIO) to the casting solution leads to finer morphologies in the active layer and a two-fold enhancement in the device efficiencies. Nevertheless, further increasing the DIO content of the casting solution leads to lower photocurrents and power conversion efficiencies, even though the morphology appears similar by energy-filtered TEM. We hypothesize that higher DIO content breaks up small RF1 aggregates, leading to suppression of charge separation. Continued development of novel non-fullerene acceptors must therefore take into consideration the balance between crystallization and aggregation of donors and acceptors for optimal performance.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Perovskite Materials and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. Understanding low bandgap polymer PTB7 and optimizing polymer solar cells based on it10.1002/adma.201400384 ↗
2. Conjugated polymer-based organic solar cells10.1021/cr050149z ↗
3. Design rules for donors in bulk-heterojunction solar cells-towards 10% energy-conversion efficiency10.1002/adma.200501717 ↗
4. Fullerene crystallisation as a key driver of charge separation in polymer/fullerene bulk heterojunction solar cells10.1039/C1SC00674F ↗
5. The Influence of poly(3-hexylthiophene) regioregularity on fullerene-composite solar cell performance10.1021/ja806493n ↗
6. Device physics of polymer:fullerene bulk heterojunction solar cells10.1002/adma.200601093 ↗
7. Domain compositions and fullerene aggregation govern charge photogeneration in polymer/fullerene solar cells10.1002/aenm.201400116 ↗
8. Effect of miscibility and percolation on electron transport in amorphous poly(3-hexylthiophene)/phenyl-C61-butyric acid methyl ester blends10.1103/PhysRevLett.108.026601 ↗
9. Polymer-fullerene miscibility: a metric for screening new materials for high-performance organic solar cells10.1021/ja305875u ↗
10. Pathways to a new efficiency regime for organic solar cells10.1002/aenm.201200103 ↗
11. Examining the effect of the dipole moment on charge separation in donor–acceptor polymers for organic photovoltaic applications10.1021/ja208642b ↗
12. Influence of acceptor structure on barriers to charge Separation in organic photovoltaic materials10.1021/jp2083133 ↗
13. How high local charge carrier mobility and an energy cascade in a three-phase bulk heterojunction enable >90% quantum efficiency10.1002/adma.201304241 ↗
14. Independent control of bulk and interfacial morphologies of small molecular weight organic heterojunction solar cells10.1021/nl302172w ↗
15. Ideal diode equation for organic heterojunctions. II. The role of polaron pair recombination10.1103/PhysRevB.82.155306 ↗
16. Additives for morphology control in high-efficiency organic solar cells10.1016/j.mattod.2013.08.013 ↗
17. Polymer:fullerene bulk heterojunction solar cells10.1016/S1369-7021(11)70210-3 ↗
18. Efficiency of bulk-heterojunction organic solar cells10.1016/j.progpolymsci.2013.05.001 ↗
19. Polymer photovoltaic cells: enhanced efficiencies via a network of internal donor-acceptor heterojunctions10.1126/science.270.5243.1789 ↗
20. Polymer-fullerene composite solar cells10.1002/anie.200702506 ↗
21. Polymer crystallization of partially miscible polythiophene/fullerene mixtures controls morphology10.1021/ma200855r ↗
22. Three-dimensional nanoscale organization of bulk heterojunction polymer solar cells10.1021/nl8014022 ↗
23. Bimolecular crystals of fullerenes in conjugated polymers and the implications of molecular mixing for solar cells10.1002/adfm.200801684 ↗
24. Rylene and related diimides for organic electronics10.1002/adma.201001402 ↗
25. Processing additives for improved efficiency from bulk heterojunction solar cells10.1021/ja710079w ↗
26. Non-fullerene acceptor-based bulk heterojunction polymer solar cells: engineering the nanomorphology via processing additives10.1002/aenm.201100285 ↗
27. Synthesis and application of poly(fluorene-alt-naphthalene diimide) as an n-type polymer for all-polymer solar cells10.1039/c2cc31752d ↗
28. All polymer photovoltaics: from small inverted devices to large roll-to-roll coated and printed solar cells10.1016/j.solmat.2013.01.025 ↗
29. A potential perylene diimide dimer-based acceptor material for highly efficient solution-processed non-fullerene organic solar cells with 4.03% efficiency10.1002/adma.201300897 ↗
30. Control of miscibility and aggregation via the material design and coating process for high-performance polymer blend solar cells10.1002/adma.201303170 ↗
31. Perylene-diimide based non-fullerene solar cells with 4.34% efficiency through engineering surface donor/acceptor compositions
32. Cooperative effects of solvent and polymer acceptor co-additives in P3HT:PDI solar cells: simultaneous optimization in lateral and vertical phase separation10.1039/c3cp55075c ↗
33. All-polymer solar cells from perylene diimide based copolymers: material design and phase separation control10.1002/anie.201005408 ↗
34. All-polymer solar cells with 3.3% efficiency based on naphthalene diimide-selenophene copolymer acceptor10.1021/ja4085429 ↗
35. Polymer donor–polymer acceptor (all-polymer) solar cells10.1016/j.mattod.2013.04.005 ↗
36. High performance all-polymer solar cell via polymer side-chain engineering10.1002/adma.201306242 ↗
37. A high-performing solution-processed small molecule:perylene diimide bulk heterojunction solar cell10.1002/adma.201301167 ↗
38. Rod-like oligomers incorporating 2,6-dialkylamino core-substituted naphthalene diimide as acceptors for organic photovoltaic10.1016/j.orgel.2013.03.039 ↗
39. Tuning the organic solar cell performance of acceptor 2,6-dialkylaminonaphthalene diimides by varying a linker between the imide nitrogen and a thiophene group10.1021/jp411432a ↗
40. Facile synthesis of end-functionalized regioregular poly(3-alkylthiophene)s via modified Grignard metathesis reaction10.1021/ma051096q ↗
41. Quantification of thin film crystallographic orientation using X-ray diffraction with an area detector10.1021/la904840q ↗
42. Mechanism of crystallization and implications for charge transport in poly(3-ethylhexylthiophene) thin films10.1002/adfm.201304247 ↗
43. Effect of solvent mixture on the nanoscale phase separation in polymer solar cells10.1002/adfm.200701459 ↗
44. Fast-grown interpenetrating network in poly(3-hexylthiophene): methanofullerenes solar cells processed with additive10.1021/jp810798z ↗
45. Mesoscopic structural length scales in P3HT/PCBM mixtures remain invariant for various processing conditions10.1021/cm4011426 ↗
46. Correlating the scattered intensities of P3HT and PCBM to the current densities of polymer solar cells10.1039/C0CC02927K ↗
47. Reconciling STEM and X-ray scattering data to determine the nanoscale ionic aggregate morphology in sulfonated polystyrene ionomers10.1021/ma800805m ↗
48. Delocalization and dielectric screening of charge transfer states in organic photovoltaic cells10.1038/ncomms4245 ↗
49. Morphology characterization in organic and hybrid solar cells10.1039/c2ee22056c ↗