Current spreading effects in fully printed p-channel organic thin film transistors with Schottky source–drain contacts
Source abstract
Abstract
Contact effects have been analyzed, by using numerical simulations, in fully printed p-channel OTFTs based on a pentacene derivative as organic semiconductor and with Au source/drain contacts. Considering source-drain Schottky contacts, with a barrier height of 0.46 eV, device characteristics can be perfectly reproduced. From the detailed analysis of the current density we have shown that current spreading occurs at the source contact, thus influencing the effective contact resistance. At low Vds and for a given Vgs, the current is mainly injected from an extended source contact region and current spreading remains basically constant for increasing Vds. However, by increasing Vds the depletion layer of the Schottky contact expands and reaches the insulator-semiconductor interface, causing the pinch-off of the channel at the source end (Vdsat1). For Vds > Vdsat1 the current injected from the edge of the source contact rapidly increases while the current injected from the remaining part of the source contact basically saturates. Current spreading shows a Vgs-dependence, since the contact injection area depends on the channel resistance and also barrier lowering of the Schottky source contact depends upon Vgs. The injected current from the edge of the source contact can be reproduced using the conventional diode current expression, assuming a constant value for the zero barrier lowering saturation current and considering a Vgs-dependent barrier lowering. The presented analysis clarifies the Vgs-dependence of the contact current-voltage characteristics and points out that the I-V contact characteristics cannot directly be related to a single diode characteristics. Indeed, the contact characteristics result from the combination of two rather different regimes: at low Vds the current is injected from an extended source contact region with a current spreading related to Vgs, while for Vds above the pinch-off of the channel at source end, the current is injected primarily from the edge of the source contact and is strongly enhanced by the barrier lowering.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Organic Electronics and Photovoltaics · Thin-Film Transistor Technologies · Conducting polymers and applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. An experimental study of contact effects in organic thin film transistors10.1063/1.2215132 ↗
2. Nonlinear charge injection in organic field-effect transistors10.1063/1.1858874 ↗
3. Modeling of organic thin film transistors of different designs10.1063/1.1323534 ↗
4. Hole-injection barrier in pentacene field-effect transistor with Au electrodes modified by C16H33SH10.1063/1.2789699 ↗
5. Injection-limited contact in bottom-contact pentacene organic thin-film transistors10.1016/j.tsf.2006.10.074 ↗
6. Analysis of the contact resistance in staggered, top-gate organic field-effect transistors10.1063/1.2804288 ↗
7. Understanding contact behavior in organic thin film transistors10.1063/1.3479531 ↗
8. Modeling the gate bias dependence of contact resistance in staggered polycrystalline organic thin film transistors10.1016/j.orgel.2009.05.019 ↗
9. Effect of active layer thickness on electrical characteristics of pentacene TFTs with PMMA buffer layer10.1016/j.sse.2007.10.010 ↗
10. Contact effects in high performance fully printed p-channel organic thin film transistors10.1063/1.3669701 ↗
11. Influence of carrier mobility and contact barrier height on the electrical characteristics of organic transistors10.1063/1.1527983 ↗
12. Influence of traps on top and bottom contact field-effect transistors based on modified poly(phenylene–vinylene)10.1063/1.2776252 ↗
13. Interdependence of contact properties and field- and density-dependent mobility in organic field-effect transistors10.1063/1.3058640 ↗
14. Fundamental benefits of the staggered geometry for organic field-effect transistors10.1109/LED.2011.2160249 ↗
15. Analysis of contact effects in fully printed p-channel organic thin film transistors10.1016/j.orgel.2012.06.003 ↗
16. Gate-bias assisted charge injection in organic field-effect transistors10.1016/j.orgel.2012.04.029 ↗
17. Relation between injection barrier and contact resistance in top-contact organic thin-film transistors10.1016/j.orgel.2012.05.009 ↗
18. Chiang · Jpn. J. Appl. Phys. · 1998 · 37 · 591410.1143/JJAP.37.5914 ↗
19. A. Daami, C. Bory, M. Benwadih, S. Jacob, R. Gwoziecki, I. Chartier, R. Coppard, C. Serbutoviez, L. Maddiona, E. Fontana, A. Scuderi., ISSCC Dig. Tech. Papers, Feb. (2011) pp. 328–330.
20. Synopsys Inc., Mountain View, CA. .
21. Analysis of electrical characteristics of high performance pentacene thin-film transistors with PMMA buffer layer10.1016/j.jnoncrysol.2005.11.123 ↗
22. Aging effects in pentacene thin-film transistors: analysis of the density of states modification10.1063/1.2203742 ↗
23. Charge transport in organic semiconductors10.1021/cr050140x ↗
24. Variable temperature mobility analysis of n-channel, p-channel, and ambipolar organic field-effect transistors10.1002/adfm.200900831 ↗
25. Sze · 1981