journal article·2026-03-01Open access

Structure, electrical, and giant dielectric properties of fine-grained Na 1/2 Bi 1/2 Cu 3 Ti 4 O 12 ceramics synthesized by mechanochemical activation and low-temperature spark plasma sintering

Mohamad M. Ahmad, Yohei Yamane, Abdullah Alshehab, Mohammed A. Alkhalifah, Nagih M. Shaalan, H. Mahfoz Kotb

Materials Science-Poland· Volume 44· Issue 1

Abstract

Abstract Na 0.5 Bi 0.5 Cu₃Ti₄O₁₂ (NBCTO) ceramics were synthesized by mechanochemical milling followed by spark plasma sintering (SPS) at 800–900°C. X-ray diffraction confirmed the cubic perovskite structure, with minor CuO traces at lower sintering temperatures and phase-pure NBCTO at 900°C. Scanning electron microscope and energy-dispersive X-ray spectroscopy revealed dense, fine-grained microstructures with average grain sizes below 400 nm, significantly smaller than those observed in conventionally sintered samples. All SPS-NBCTO ceramics exhibited colossal dielectric permittivity ( ε ′ > 10⁴) across wide frequency and temperature ranges, with values of 2.8–4.0 × 10⁴ at 1 kHz and room temperature. Impedance analysis revealed an internal barrier layer capacitance mechanism, with semiconducting grains and more resistive grain boundaries. Grain conductivity (∼3 × 10⁻² S/cm) and activation energies (0.089–0.096 eV) were consistent with CaCu₃Ti₄O₁₂-based systems, while grain boundary conductivity was unexpectedly high (2.5–3.5 × 10⁻³ S/cm) with relatively low activation energies (0.192–0.211 eV). These properties, linked to oxygen-vacancy-related conduction, led to unusually large dielectric losses. Relaxation analysis using the electric modulus confirmed thermally activated grain and grain boundary processes with activation energies matching conductivity values. The results demonstrate that SPS enables fine-grained, dense NBCTO ceramics with colossal dielectric constants, though excessive grain boundary conduction remains a challenge.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Dielectric properties of ceramics · Dielectric materials and actuators · Ferroelectric and Piezoelectric Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Physics, College of Science, King Faisal University , P.O. Box 400 , Hofuf , Al-Ahsa 31982 , Saudi Arabia

Department of Applied Molecular Chemistry, College of Industrial Technology, Nihon University, Narashino 275-8575 , Chiba , Japan

Department of Chemistry, College of Science, King Faisal University , P.O. Box 400 , Hofuf , Al-Ahsa 31982 , Saudi Arabia

Physics Department, Faculty of Science, Assiut University , Assiut 71516 , Egypt

References (46)

Show source-provided references
1. Du, C., Li, X.-K., Zhou, D., Wang, S.-F., Li, R.-L., Yao, X.-G., et al., Fabrication of high radiation efficiency dielectric resonator antenna array using temperature stable 0.8Zn2SiO4‐0.2TiO2 microwave dielectric ceramic, Adv. Mater. Technol., 2023; 8: 220198510.1002/admt.202201985 ↗
2. Chen, Z., Zheng, Y., Li, B., A new microwave dielectric ceramic TmVO4 with high-quality factor and the effect of TiO2 on its microwave dielectric properties, J. Mater. Sci. Mater. Electron., 2023; 34: 82810.1007/s10854-023-10254-8 ↗
3. Sreejivungsa, K., Kosolwattana, S., Sakulsombat, M., Thongbai, P., Colossal permittivity and humidity sensing properties of CaCu3Ti4O12 ceramics derived from cockle shell CaCO3 via CO2 absorption, Sci. Rep., 2025; 15: 1803010.1038/s41598-025-03201-6 ↗
4. Dev, A., Das, T., Biswas, P., Shukla, A., Kour, P., Pradhan, S.K., et al., Enhancing dielectric characteristics of calcium copper titanate via lattice site modification, J. Mater. Sci., 2025; 60: 12859–1287710.1007/s10853-025-11229-2 ↗
5. Xiao, M., Wang, H., Tuersun, G., Feng, K., Bai, W., Zhou, Y., et al., Electrical resistance transition of CaCu3Ti4O12 ceramics induced by cyclic voltammetry conditioning, Ceram. Int., 2025; 50: 4233310.1016/j.ceramint.2024.08.078 ↗
6. Petinardi, G.M., Thomazini, D., Uribe, J.O.M., Gelfuso, M.V., Non-stoichiometry influence on dielectric properties of CaCu3Ti4O12 based ceramics, Mater. Sci. Eng. B, 2024; 300: 11709510.1016/j.mseb.2023.117095 ↗
7. Haque, M.E., Jose, M., Investigating the impact of Nd3+ and V5+ Co‐doping on the dielectric response and microstructure of CaCu3Ti4O12 ceramics, J. Am. Ceram. Soc., 2025; 108: e7007710.1111/jace.70077 ↗
8. Moreno, H., Teixeira, V.C., Ponce, M.A., Macchi, C.E., Aldao, C.M., Bezzon, V.D.N., et al., Tuning dielectric and nonohmic properties of CaCu3Ti4O12 ceramics with W doping, Mater. Res. Bull., 2025; 190: 11349310.1016/j.materresbull.2025.113493 ↗
9. Lahrar, E., ELHarrak, A., Yahakoub, E., Bendahhou, A., Essaoudi, H., Faik, A., Structural evolution, electrical properties, and non-ohmic behavior of barium-doped CaCu3Ti4O12 ceramics synthesized via solid-state method, Ceram. Int., 2025; 51: 4009810.1016/j.ceramint.2025.06.244 ↗
10. Boonlakhorn, J., Promsai, S., Pinsook, U., Thongbai, P., Srepusharawoot, P., Intrinsic and extrinsic factors associated with enhancing dielectric properties of Ni2+ and Sn4+ substituted CaCu3Ti4O12 ceramics, Ceram. Int., 2025; 51: 2141210.1016/j.ceramint.2025.02.301 ↗
11. Rhouma, S., Megriche, A., Souidi, E., Said, S., Autret-Lambert, C., Simultaneous improvement of permittivity and nonlinear properties and loss tangent reduction through semi-wet route in NiO-modified CaCu3Ti4O12 ceramics: grain boundaries effect, J. Mater. Sci.: Mater. Electron., 2025; 36: 89310.1007/s10854-025-14977-8 ↗
12. Rani, K., Ahlawat, N., Kundu, R.S., Pooja, Saini, D., Deepa, Influence of Ho3+ doping on microstructure and dielectric properties of CaCu3Ti4O12 lead free ceramic, J. Phys. D.: Appl. Phys., 2025; 58: 13550310.1088/1361-6463/adaf31 ↗
13. Haque, M.E., Jose, M., La3+ doped CaCu3Ti4O12 ceramics: Investigation of its microstructural and dielectric properties against varying sintering durations, Inorg. Chem. Commun., 2024; 169: 11304010.1016/j.inoche.2024.113040 ↗
14. Ramakrishna, B., Charan, P.H.K., Jagadeesh, Ch, Neeraja, R., Ramanaiah, M.E.C.S., Enhanced grain boundary resistance resulting in high permittivity and low dielectric loss in CaCu3Ti4O12/LaNiO3, J. Solid State Sci. Technol., 2024; 13: 11300910.1149/2162-8777/ad8f62 ↗
15. Jalafi, I., Chaou, F., Bouazzati, W., Yahakoub, E., Bendahhou, A., ElBarkany, S., et al., Synthesis and characterization of new doped dielectric materials based on CaCu3Ti4O12 (CCTO) applied at high temperature, J. Solid State Chem., 2024; 331: 12450610.1016/j.jssc.2023.124506 ↗
16. Djafar, R., Boumchedda, K., Fasquelle, D., Chaouchi, A., Sedda, K., Bououdina, M., et al., Tuning the dielectric properties of CaCu3Ti4O12 ceramic by Cu2O addition and microstructural modifications, Phys. B, 2023; 661: 41492010.1016/j.physb.2023.414920 ↗
17. Xue, R., Liu, X., Yang, Y., Zhu, X., Li, T., Optimization of the dielectric properties in Mn-doped Bi2/3Cu3Ti4O12 ceramics, Phys. Scr., 2025; 100: 08591810.1088/1402-4896/adee6d ↗
18. Adams, T.B., Sinclair, D.C., West, A.R., Giant barrier layer capacitance effects in CaCu3Ti4O12 ceramics, Adv. Mater., 2002; 14: 132110.1002/1521-4095(20020916)14:18<1321::AID-ADMA1321>3.0.CO;2-P ↗
19. Hu, W., Liu, Y., Withers, R.L., Frankcombe, T.J., Norén, L., Snashall, A., et al., Electron-pinned defect-dipoles for high-performance colossal permittivity materials, Nat. Mater., 2013; 12: 82110.1038/nmat3691 ↗
20. Boonlakhom, J., Suksangrat, P., Sarakorn, W., Krongsuk, S., Thongbai, P., Srepusharawoot, P., Computational and experimental investigations of the giant dielectric property of Na1/2Y1/2Cu3Ti4O12 ceramics, Sci. Rep., 2023; 13: 463810.1038/s41598-023-31879-z ↗
21. Yuan, L., Zhang, T., Han, D-D., Effects of multiple cations and sintering temperature on microstructure and dielectric properties in Na1/2Ln1/2Cu3Ti4O12 (Ln = Sm and Eu) ceramic materials, Sci. Rep., 2023; 13: 1528510.1038/s41598-023-42610-3 ↗
22. Boonlakhom, J., Suksangrat, P., Chanlek, N., Sarakorn, W., Krongsuk, S., Thongbai, P., Dielectric properties with high dielectric permittivity and low loss tangent and nonlinear electrical response of sol-gel synthesized Na1/2Sm1/2Cu3Ti4O12 perovskite ceramic, J. Eur. Ceram. Soc., 2022; 42: 565910.1016/j.jeurceramsoc.2022.06.030 ↗
23. Kotb, H.M., Khater, H.A., Saber, O., Ahmad, M.M., Sintering temperature, frequency, and temperature dependent dielectric properties of Na0.5Sm0.5Cu3Ti4O12 ceramics, Materials, 2021; 14: 480510.3390/ma14174805 ↗
24. Jumpatam, J., Putasaeng, B., Boonlakhorn, J., Thongbai, P., Structural, dielectric, non-ohmic, and humidity-sensing properties of Na0.5Nd0.5Cu3Ti4O12 ceramic, J. Alloys. Comp., 2025; 1032: 18112610.1016/j.jallcom.2025.181126 ↗
25. Changchuea, A., Promsai, S., Khongpakdee, S., Mani, M., Intachai, S., Boonlakhorn, J., et al., Structural and dielectric characterization of La2/3Cu3Ti4O12 ceramics synthesized via a solid-state reaction combined with a double calcination process, Mater. Chem. Phys., 2025; 343: 13102410.1016/j.matchemphys.2025.131024 ↗
26. Kotb, H.M., Ahmad, M.M., Ansari, S.A., Kayed, T.S., Alshoaibi, A., Dielectric properties of colossal-dielectric-constant Na1/2La1/2Cu3Ti4O12 ceramics prepared by spark plasma sintering, Molecules, 2022; 27: 77910.3390/molecules27030779 ↗
27. Liu, X., Li, Y., Zeng, L., Li, X., Chen, N., Bai, S., et al., A review on mechanochemistry: approaching advanced energy materials with greener force, Adv. Mater., 2022; 34, 210832710.1002/adma.202108327 ↗
28. Reynes, J.F., Leon, F., García, F., Mechanochemistry for organic and inorganic synthesis, ACS Org. Inorg. Au, 2024; 4: 43210.1021/acsorginorgau.4c00001 ↗
29. Szczesniak, B., Choma, J., Jaroniec, M., Advances in microwave synthesis of nanoporous materials, Mater. Adv., 2021; 2: 251010.1039/D1MA00073J ↗
30. Ahmad, M.M., Al-Libidi, E., Aljaafari, A., Ghazanfar, S., Yamada, K., Mechanochemical synthesis and giant dielectric properties of CaCu3Ti4O12, App.l Phys. A, 2014; 116: 1299–130610.1007/s00339-014-8224-7 ↗
31. Ahmad, M.M., Giant dielectric constant in CaCu3Ti4O12 nanoceramics, Appl. Phys. Lett., 2013; 102: 23290810.1063/1.4811154 ↗
32. Lin, H., Xu, W., Zhang, H., Chen, C., Zhou, Y., Yi, Z., Preparation of multifunctional dopamine-coated zerovalent iron/reduced graphene oxide for targeted phototheragnosis in breast cancer, J. Eur. Ceram. Soc., 2020; 40: 195710.3390/nano10101957 ↗
33. Ahmad, M.M., Kotb, H.M., Giant dielectric properties of fine-grained Na1/2Y1/2Cu3Ti4O12 ceramics prepared by mechanosynthesis and spark plasma sintering, J. Mater. Sci.: Mater. Electron., 2015; 26: 893910.1007/s10854-015-3576-0 ↗
34. Kotb, H.M., Ahmad, M.M., Aldabal, S., Alshoaibi, A., Aljaafari, A., Structural and dielectric behavior of Al-substituted CaCu3Ti4O12 ceramics with giant dielectric constant by spark plasma sintering, J. Mater. Sci.: Mater. Electron., 2019; 30: 1825910.1007/s10854-019-02180-5 ↗
35. Li, J., Li, F., Li, C., Yang, G., Xu, Z., Zhang, S., Evidences of grain boundary capacitance effect on the colossal dielectric permittivity in (Nb + In) co-doped TiO2 ceramics, Sci. Rep., 2015; 5: 829510.1038/srep08295 ↗
36. Zhang, L., Feng, S., Wang, N., Li, J., Li, H., Xu, D., Dielectric performance of DC electric field-assisted flash sintered (Sr, Sb) co-doped TiO2 ceramics, ECS J. Solid State Sci. Technol., 2023; 12: 11300510.1149/2162-8777/ad05b7 ↗
37. Ferrarelli, M.C., Adams, T.B., Feteira, A., Sinclair, D.C., West, A.R., High intrinsic permittivity in Na1∕2Bi1∕2Cu3Ti4O12, Appl. Phys. Lett., 2006; 89: 21290410.1063/1.2388251 ↗
38. Sun, X., Wang, C., Wang, G., Lei, C., Li, T., Liu, L., Low‐temperature dielectric relaxations associated with mixed‐valent structure in Na0.5Bi0.5Cu3Ti4O12, J. Am. Ceram. Soc., 2013; 96: 1497
39. Ren, H., Liang, P., Yang, Z., Processing, dielectric properties and impedance characteristics of Na0.5Bi0.5Cu3Ti4O12 ceramics, Mater. Res. Bull., 2010; 45: 160810.1016/j.materresbull.2010.07.018 ↗
40. Tuichai, W., Thongbai, P., Amornkitbamrung, V., Yamwong, T., Maensiri, S., Na0.5Bi0.5Cu3Ti4O12 nanocrystalline powders prepared by a glycine–nitrate process: Preparation, characterization, and their dielectric properties, Microelectron. Eng., 2014; 126: 11810.1016/j.mee.2014.07.002 ↗
41. Tuichai, W., Danwittayakul, S., Yamwong, T., Thongbai, P., Synthesis, dielectric properties, and influences oxygen vacancies have on electrical properties of Na1/2Bi1/2Cu3Ti4O12 ceramics prepared by a urea combustion method, J. Sol-Gel Sci. Technol., 2015; 76: 63010.1007/s10971-015-3814-1 ↗
42. Su, Y., Song, J., Liu, R., Huang, H., Fabrication and dielectric properties of Na0.5Bi0.5Cu3Ti4O12 from co-precipitation method, J. Electroceram., 2013; 30: 16610.1007/s10832-013-9779-y ↗
43. Qiu, Y., Yuan, S., Tian, Z., Chen, L., Wang, C., Duan, H., et al., Grain size effect on the giant dielectric and nonlinear electrical behaviors of Bi1/2Na1/2Cu3Ti4O12 ceramics, Appl. Phys. A, 2012; 107: 37910.1007/s00339-012-6806-9 ↗
44. Su, Y., Wang, Y., Synthesis and dielectric properties of Na0.5Bi0.5Cu3Ti4O12 ceramic by molten salt method, Appl. Phys. A. 2016; 122: 24910.1007/s00339-016-9838-8 ↗
45. Pawar, S.M., Kim, J., Inamdar, A.I., Woo, H., Jo, Y., Pawar, B.S., et al., Multi-functional reactively-sputtered copper oxide electrodes for supercapacitor and electro-catalyst in direct methanol fuel cell applications, Sci. Rep., 2016; 6: 2131010.1038/srep21310 ↗
46. Fang, T.T., Mei, L.T., Evidence of Cu deficiency: a key point for the understanding of the mystery of the giant dielectric constant in CaCu3Ti4O12, J. Am. Ceram. Soc., 2007; 90: 63810.1111/j.1551-2916.2006.01419.x ↗