Semiconductor WO3 thin films deposited by pulsed reactive magnetron sputtering
Source abstract
Abstract
A pulsed reactive magnetron sputtering system with a tungsten target and a gas mixture of argon and oxygen was investigated as a source for the deposition of semiconductor WO 3 thin films on soda lime glass substrates and on the glass with transparent conductive SnO 2 :F (FTO) electrode. The reactive sputtering process was performed in HiPIMS mode with low pulse repetition frequency f p ≈ 50–100 Hz and short pulse duration in HiPIMS discharge T on = 100 μs. The second mode investigated was the mid-frequency (MF) magnetron discharge with pulse frequency f p = 40 kHz and pulse length T on = 15 μs. The plasma parameters were investigated for both HiPIMS and MF modes using the planar RF probe operating at the frequency f probe = 350 kHz and the grid QCM with biased collector electrode. Ion density n i and tail electron temperature (T e ) were determined in both pulsed reactive magnetron sputtering discharge modes with time resolution. The maximum value n i ≈ 5 · 10 17 m −3 was found in the reactive HiPIMS mode, and the maximum value n i ≈ 7 · 10 16 m −3 was found in the reactive MF (40 kHz) mode. The degree of ionization of sputtered particles in reactive HiPIMS was determined for different values of (Q O2 ) and was found to be in the range of r i ≈ 0.1–0.3. The deposition rate determined by QCM in reactive HiPIMS was practically independent on (Q O2 ), but in the case of reactive MF, the measured deposition rate decreased significantly with increasing (Q O2 ). The WO 3 films deposited in both modes have a predominantly monoclinic crystal structure. The light and dark conductivity and the light/dark conductivity ratio (L d ) were measured under dark conditions and UV light illumination. At higher (Q O2 ), the maximum value of L d ≈ 300 was found for MF deposited WO 3 and the maximum value of L d ≈ 30 was found for HiPIMS deposited WO 3 . The photoelectrochemical measurement of WO 3 deposited on FTO electrodes confirmed the n-type conductivity, and these films functioned as photoanodes in photoelectrochemical cells. MF deposited WO 3 films systematically exhibited slightly higher photocurrents than HiPIMS deposited WO 3 . It was shown that these optimum photocurrents for HiPIMS and MF were found at Q O2 ≈ 80 sccm and could not be improved by further increasing of (Q O2 ). • HIPIMS and MF reactive pulsed sputtering were used to deposit semiconductor crystalline WO 3 films with photoresponse. • Plasma parameters in HiPIMS and MF sputtering systems were determined by RF probe and g-QCM. • HiPIMS deposited WO 3 films have significantly larger crystallites than MF deposited WO 3 films. • MF deposited WO 3 films have higher photoresponse and lower dark conductivity than HiPIMS deposited WO 3 .
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Gas Sensing Nanomaterials and Sensors · Transition Metal Oxide Nanomaterials · ZnO doping and properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. Tungsten-based oxide semiconductors for solar hydrogen generation10.1016/j.cattod.2012.07.020 ↗
2. Tungsten trioxide nanostructures for photoelectrochemical water splitting: material engineering and charge carrier dynamic manipulation
3. Nanostructure-based WO3 photoanodes for photoelectrochemical water splitting10.1039/c2cp40976c ↗
4. A review on the development of visible light-responsive WO3-based photocatalysts for environmental applications10.1016/j.ceja.2020.100070 ↗
5. High-performance electrochromic WO3 film driven by controllable crystalline structure and its all-solid-state device10.1016/j.solmat.2021.111564 ↗
6. Amorphous/crystalline WO3 dual phase laminated films: fabrication, characterization and evaluation of their electrochromic performance for smart window applications10.1016/j.solmat.2022.111820 ↗
7. Multivalent-ion versus proton insertion into nanostructured electrochromic WO3 from mild aqueous electrolytes
8. Giant persistent photoconductivity of the WO3 nanowires in vacuum condition10.1007/s11671-010-9800-1 ↗
9. Transient photoconductivity properties of tungsten oxide thin films prepared by spray pyrolysis10.1063/1.1412567 ↗
10. Photoresponse in thin films of WO3 grown by pulsed laser deposition10.1063/1.4882658 ↗
11. High power pulsed magnetron sputtered CrNx films10.1016/S0257-8972(02)00479-6 ↗
12. Synthesis of α-Al2O3 thin films using reactive high-power impulse magnetron sputtering10.1209/0295-5075/82/36002 ↗
13. Investigation of reactive high power impulse magnetron sputtering processes using various target material–reactive gas combinations10.1016/j.surfcoat.2010.12.038 ↗
14. Studies of hysteresis effect in reactive HiPIMS deposition of oxides10.1016/j.surfcoat.2011.01.019 ↗
15. Hysteresis-free deposition of niobium oxide films by HiPIMS using different pulse management strategies10.1088/0022-3727/45/5/055204 ↗
16. Deposition of photocatalytic titania coatings on polymeric substrates by HiPIMS10.1016/j.vacuum.2012.05.003 ↗
17. Plasma reactivity in high-power impulse magnetron sputtering through oxygen kinetics10.1063/1.4819835 ↗
18. Process stabilization and a significant enhancement of the deposition rate in reactive high-power impulse magnetron sputtering of ZrO2 and Ta2O5 films10.1016/j.surfcoat.2013.10.052 ↗
19. Evolution of discharge parameters and sputtered species ionization in reactive HiPIMS with oxygen, nitrogen and acetylene10.1088/1361-6595/ab0363 ↗
20. Mid-frequency reactive sputtering of dielectrics: Al2O310.1016/S0257-8972(03)00369-4 ↗
21. Time-resolved Langmuir probe measurements at the substrate position in a pulsed mid-frequency DC magnetron plasma10.1016/S0257-8972(00)00990-7 ↗
22. A comparison of the properties of titanium-based films produced by pulsed and continuous DC magnetron sputtering10.1016/S0257-8972(03)00356-6 ↗
23. Properties of pulsed magnetron sputtered TiO2 coatings grown under different magnetron configurations and power deliver modes10.1002/ppap.200730804 ↗
24. Enhancement of the deposition rate in reactive mid-frequency ac magnetron sputtering of hard and optically transparent ZrO2 films10.1016/j.surfcoat.2017.09.015 ↗
25. Aluminum tantalum oxide thin films deposited at low temperature by pulsed direct current reactive magnetron sputtering for dielectric applications10.1016/j.vacuum.2023.112881 ↗
26. High rate reactive sputter deposition of TiO2 films for photocatalyst and dye-sensitized solar cells10.7567/JJAP.50.045802 ↗
27. High rate reactive magnetron sputter deposition of Al-doped ZnO with unipolar pulsing and impedance control system10.1116/1.3308621 ↗
28. Enhanced photoelectrochemical properties of WO3 thin films fabricated by reactive magnetron sputtering10.1016/j.ijhydene.2011.01.087 ↗
29. Tungsten oxide thin films for electrochromic applications: pulse width-controlled deposition by high-power impulse magnetron sputtering10.1002/adem.202301378 ↗
30. Effects of film density on electrochromic tungsten oxide thin films deposited by reactive dc-pulsed magnetron sputtering10.1016/j.jallcom.2010.03.155 ↗
31. Transparent conductive Dielectric−Metal−Dielectric structures for electrochromic applications fabricated by high-power impulse magnetron sputtering10.1021/acsami.9b00191 ↗
32. Synergy of experiment and model for reactive HiPIMS: effect of discharge parameters on WOx composition and deposition rate10.1088/1361-6463/abd1a3 ↗
33. WO3 thin films prepared by sedimentation and plasma sputtering10.1016/j.cej.2016.09.083 ↗
34. Semiconducting WO3 thin films prepared by pulsed reactive magnetron sputtering10.1007/s11164-015-1991-8 ↗
35. Deposition of tungsten oxide films by reactive magnetron sputtering on different substrates10.1116/6.0002012 ↗
36. Hardware and power management for high power impulse magnetron sputtering
37. Modified high frequency probe approach for diagnostics of highly reactive plasma10.1088/1361-6595/ab506c ↗
38. Semiconducting p-type copper iron oxide thin films deposited by hybrid reactive-HiPIMS + ECWR and reactive-HiPIMS magnetron plasma system10.3390/coatings10030232 ↗
39. Plasma electron characterization in electron chemical vapor deposition10.1116/6.0003408 ↗
40. Measuring the ion current in electrical discharges using radio-frequency current and voltage measurements10.1063/1.121032 ↗
41. Experimental test of models of high-plasma-density, radio-frequency sheaths
42. Investigation of ionized metal flux fraction in HiPIMS discharges with Ti and Ni targets10.1016/j.surfcoat.2013.10.064 ↗
43. Magnetron sputter deposition with high levels of metal ionization10.1063/1.110176 ↗
44. Determination of flux ionization fraction using a quartz crystal microbalance and a gridded energy analyzer in an ionized magnetron sputtering system10.1063/1.1148430 ↗
45. Ionized metal flux fraction measurements in HiPIMS discharges10.1088/0022-3727/45/32/322001 ↗
46. 2005 · 1
47. Discharge physics of high power impulse magnetron sputtering10.1016/j.surfcoat.2011.03.081 ↗
48. A unified treatment of self-sputtering, process gas recycling, and runaway for high power impulse sputtering magnetrons10.1088/1361-6595/aa959b ↗
49. Piel · 2010
50. Transition between the discharge regimes of high power impulse magnetron sputtering and conventional direct current magnetron sputtering10.1088/0963-0252/18/4/045008 ↗
51. Evolution of target condition in reactive HiPIMS as a function of duty cycle: an opportunity for refractive index grading10.1063/1.4977824 ↗
52. Pulse length dependence of a reactive high power impulse magnetron (HiPIMS) discharge10.1088/1361-6595/acd5fc ↗
53. Transition metal oxide work functions: the influence of cation oxidation state and oxygen vacancies10.1002/adfm.201200615 ↗
54. Deposition of hematite Fe2O3 thin film by DC pulsed magnetron and DC pulsed hollow cathode sputtering system10.1016/j.tsf.2013.09.031 ↗