journal article·2024-11

Optimization of surface filtration to enhance wafer uniformity by removing large particle in ceria slurry

Seungjun Oh, Geumji Back, Sanghyeon Park, HunWook Lee, Heedo Seo, Yoonsub Kim, Taesung Kim

Publisher page

Abstract

Owing to the limitations of scaling down, the development of complex structures for chip design is progressing in the semiconductor industry. As a result, the chemical mechanical polishing (CMP) process has become essential for the precise control of micro-level steps and for maintaining surface uniformity between layers during the stacking process. Structural management and improved performance of the consumables used in CMP processes are required. In particular, controlling the abrasive particles in the slurry that directly contact the wafer surface is crucial. Large particles within the slurry can occur scratches and cause non-uniformity in the polishing process, thus the particle size distribution of the slurry must be regulated. In this study, two types of filtration systems were constructed to determine the optimal conditions for CMP of ceria slurry. Depth filtration effectively removes particles through a cake layer formation mechanism but has limitations in achieving a consistent pore size within the fiber layer. Consequently, separation efficiency for particle sizes is relatively low. In contrast, surface filtration consisting of a single membrane demonstrates a consistent correlation between pore size and the size of the filtered particles, resulting in high particle removal efficiency. The pore size capable of removing large particles without active particle loss was 200 nm. After evaluating slurry productivity and filter-induced agglomeration, 0.8 L per minute (LPM) was identified as the optimal flow rate. Additionally, after filtration at 0.8 LPM, the maximum reduction in removal rates was relatively small at 272.54 Å/min due to decreased edge removal rates. However, by removing large particles to implement a monodisperse state, an improvement in uniformity of 17.11 % was achieved. Therefore, the CMP performance can be enhanced using surface filtration to control the particle size distribution (PSD).
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Surface Polishing Techniques · Advanced Machining and Optimization Techniques · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Cleaning methodology of small residue defect with surfactant in copper chemical mechanical polishing post-cleaning10.1016/j.tsf.2016.05.007 ↗
2. Wafer-level packaging and direct interconnection technology based on hybrid bonding and through silicon vias10.1088/0960-1317/21/8/085032 ↗
3. Study on the effect of ceria concentration on the silicon oxide removal rate in chemical mechanical planarization10.1016/j.colsurfa.2020.125670 ↗
4. Controllable CMP of oxide film by using colloidal ceria slurry
5. Correlation of large particle count data in CMP slurry with production wafer defects
6. Scratch formation and its mechanism in chemical mechanical planarization (CMP)10.1007/s40544-013-0026-y ↗
7. Analysis of large particle count in fumed silica slurries and its correlation with scratch defects generated by CMP10.1149/1.2184036 ↗
8. Analysis of the defect density according to the slurry filter size in the chemical mechanical polishing process10.3938/jkps.43.798 ↗
9. Effects of large particles on MRR, WIWNU and surface quality in TEOS chemical mechanical polishing based on FA/O alkaline slurry10.1149/2.0101811jss ↗
10. Chemical mechanical polishing performances by filtering and retreatment of used silica abrasives slurry10.1016/j.mee.2004.12.035 ↗
11. Investigation of the barrier slurry with better defect performance and facilitating post-CMP cleaning10.1016/j.mee.2016.12.002 ↗
12. Real-time, continuous large particle monitoring for CMP slurry quality control
13. Effect of controlling abrasive size in slurry for tungsten contact CMP process10.1149/2.0311905jss ↗
14. Reduction of micro-scratch using slurry filter in oxide CMP (chemical mechanical polishing) for multi-level interconnections
15. Effects of slurry filter size on the chemical mechanical polishing (CMP) defect density10.1016/j.matlet.2004.01.012 ↗
16. Advantages of point of use (POU) slurry filter and high spray method for reduction of CMP process defects10.1016/S0167-9317(03)00278-8 ↗
17. Precision flow control and enhanced filter lifetime in magnetically levitated pump based CMP slurry delivery systems
18. Tangential flow filtration of ceria slurry: application of a single-pass method to improve buff cleaning10.1016/j.mssp.2022.106618 ↗
19. The how's and why's of characterizing particle size distributions in CMP slurries
20. Shear thickening and defect formation of fumed silica CMP slurries10.1016/j.colsurfa.2013.06.003 ↗
21. Evaluation of chemical mechanical planarization slurry dispersion using a combined scanning mobility particle sizer-optical particle sizer system
22. A new Navier-Stokes and Darcy's law combined model for fluid flow in crossflow filtration tubular membranes10.1016/S0011-9164(04)90041-0 ↗
23. Reducing slurry agglomeration with low shear filtration
24. Effect of flow rate and concentration on filtration efficiency of colloidal abrasives
25. The benefits of multi-stage filtration for improved CMP slurry large particle retention
26. Effects of surface zeta potential on the filtration behavior of colloidal abrasives
27. Optimizing flux capacity of dead-end filtration membranes by controlling flow with pulse width modulated periodic backflush10.1038/s41598-020-57649-9 ↗
28. Effect of filtration pressure on the particle penetration efficiency of fibrous filter media10.1016/j.seppur.2021.119086 ↗
29. Removal of polystyrene nanoplastic beads using gravity-driven membrane filtration: mechanisms and effects of water matrices10.1016/j.cej.2022.138484 ↗
30. Air filtration media from electrospun waste high-impact polystyrene fiber membrane10.1088/2053-1591/aab6ef ↗
31. Large particle reduction by porous membrane filter
32. Semi-empirical material removal rate distribution model for SiO2 chemical mechanical polishing (CMP) processes10.1016/j.precisioneng.2012.12.006 ↗