journal article·2024-11

Effect of abrasive particle size and oxidant concentration on CdZnTe crystal properties during CMP process

Xiaoyan Liang, Liang Yin, Jijun Zhang, Wenxuan Yang, Chen Xie, Chao Yu, Linjun Wang, Jiahua Min

Publisher page

Abstract

Cadmium Zinc Telluride (CZT) crystals are widely regarded as the optimal semiconductor materials for producing room temperature high-energy radiation detectors. The goal of polishing is to enhance the quality of the crystal surface. This paper adopts a three-step polishing process, where the first two steps involve mechanical polishing with Al 2O 3 polishing slurries of different particle sizes. The third step employs the chemical mechanical polishing (CMP) of CZT crystals with a polishing slurry of silica sol and sodium hypochlorite. The results indicate that the introduction of 300 nm Al 2O 3 alkaline transition polishing eliminates the deep scratches, which lay a foundation for the next CMP process. The experimental results of orthogonal CMP indicate that when the NaClO content is 5 %, the crystal roughness reaches its optimum over a large range of 800 × 700 μm 2, with an average roughness of 1.61 nm and minimal leakage current. Compared to the first step using 3 μm Al 2O 3 mechanical polishing, the energy resolution is significantly improved from 24.3 % to 10.5 %. Based on the analysis of CMP mechanisms, during the CMP process, NaClO forms an oxide layer through chemical reaction, softening the surface of CZT, which is easily removed by the physical action of silicon sol. When the NaClO content is 5 %, a balance between mechanical and chemical actions is achieved, leading to the optimal quality of the crystal surface. Therefore, it provides an effective surface treatment technique for preparing high-performance X-ray and γ-ray detectors by this three-step polishing method.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Semiconductor Detectors and Materials · Integrated Circuits and Semiconductor Failure Analysis · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (27)

Show source-provided references
1. Carrier transport performance of Cd0.9Zn0.1Te detector by direct current photoconductive technology10.1063/1.4974201 ↗
2. Effect of surface preparation technique on the radiation detector performance of CdZnTe10.1016/j.apsusc.2007.10.064 ↗
3. The influence of surface processing on properties of CdZnTe films prepared by close-spaced sublimation, Sur10.1016/j.surfcoat.2018.10.043 ↗
4. Study on the density of trap states between CdZnTe and passivation layer based on MIS structure10.1016/j.mssp.2022.106809 ↗
5. Study on factors influencing the edge slope of infrared absorption of CdZnTe crystal10.1016/j.mssp.2019.104871 ↗
6. Influence of surface polishing on the structural and electronic properties of CdZnTe surfaces10.1007/s11664-012-2126-2 ↗
7. Effect of surface treatments on the electrical and optical properties of CdZnTe single crystal, Nuclear Inst
8. Effects of chemical treatments on CdZnTe X-ray and gamma-ray detectors10.1109/TNS.2016.2527779 ↗
9. Influences of Te-rich and Cd-rich precipitates of CdZnTe substrates on the surface defects of HgCdTe liquid-phase epitaxy materials10.1007/s11664-014-3110-9 ↗
10. The effect of chemical polishing on the interface structure and electrical property of Au/Cd0.9Zn0.1Te contact10.1007/s00339-013-7989-4 ↗
11. Comparison of the surfaces and interfaces formed for sputter and electroless deposited gold contacts on CdZnTe10.1016/j.apsusc.2017.08.077 ↗
12. Nanoscale machinability and subsurface damage machined by CMP of soft-brittle CdZnTe crystals10.1007/s00170-009-2225-2 ↗
13. Mechanical characteristics of nanocrystalline layers containing nanotwins induced by nanogrinding of soft-brittle CdZnTe single crystals10.1016/j.scriptamat.2012.05.033 ↗
14. Investigation about elliptical region observed on CdZnTe wafers after etching treatment10.1016/j.jcrysgro.2019.05.001 ↗
15. The effect of Ar plasma etching time on the microstructure, optical and photoelectric properties of CdZnTe films10.1016/j.surfcoat.2016.04.036 ↗
16. Chemical-mechanical polishing performance of core-shell structured polystyrene@ceria/nanodiamond ternary abrasives on sapphire wafer
17. Chemical mechanical polishing of soft-brittle cadmium zinc telluride wafers using a developed environment-friendly solution
18. Material removal mechanism of precision grinding of soft-brittle CdZnTe wafers10.1007/s00170-009-2114-8 ↗
19. High-efficiency and low-damage chemical mechanical polishing process of CdZnTe crystals, Rengong Jingti Xuebao
20. CMP parameter optimization and polishing mechanism analysis of cadmium zinc telluride wafer based on the orthogonal test
21. Research on chemical-mechanical planarization slurry of CdZnTe
22. Effect of polishing parameters on chemical mechanical planarization of C-plane (0001) gallium nitride surface using SiO2 and Al2O3 abrasives
23. Effect of surfactant and electrolyte on surface modification of c-plane GaN substrate using chemical mechanical planarization (CMP) process10.1016/j.colsurfa.2016.02.035 ↗
24. Development of a novel chemical mechanical polishing slurry and its polishing mechanisms on a nickel alloy10.1016/j.apsusc.2019.144670 ↗
25. Mechanisms of local planarization improvement using solo pad in chemical mechanical polishing, jap10.7567/JJAP.52.126501 ↗
26. Surface and subsurface damage characteristics and material removal mechanism in 6H-SiC wafer grinding10.1179/1432891714Z.000000000522 ↗
27. Experimental investigation of material removal mechanism in grinding of alumina by single grain scratch test