journal article·2022-12

Non-stoichiometric effect and disorder in as-prepared Cu2ZnSnS4 films deposited at different temperatures by ultrasonic spray pyrolysis

Ibrahim Gunes, Vildan Bilgin, Emrah Sarica

Publisher page

Abstract

A better understanding of its crystal structure, the formation of possible secondary phases, defects and Cu–Zn disorder effects is needed to improve the photovoltaic device performance of CZTS films. In this direction, the effect of deposition temperature on the structural inhomogeneities, such as secondary phases and Cu–Zn disorder, etc. as well as opto-electrical properties of CZTS were experimentally examined. For this purpose, a non-stoichiometric spraying solution was prepared and ultrasonically sprayed onto glass substrates at different deposition temperatures (350 °C, 400 °C, 450 °C, and 500 °C) to obtain CZTS films. Afterward, the structural, morphological, elemental, optical, and electrical properties of the deposited films were investigated in detail. By Lorentzian deconvolution of Raman spectra, 14 Raman vibrational modes were detected and seven of these were assigned to the secondary phases. Also, the ordered-kesterite phase (337 cm−1) of CZTS was found to crystallize along with the disordered-kesterite phase (329 cm−1) due to the disorder of the cation (Cu–Zn) sublattice. Optical band gaps for CZTS films decreased from 1.89 eV to 1.42 eV with increasing in deposition temperature. It was seen that not only optical band gaps but also Cu–Zn disorder and the amount of secondary phases in CZTS films tightly depend on the deposition temperature.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Copper-based nanomaterials and applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (98)

Show source-provided references
1. A review on energy economics and the recent research and development in energy and the Cu2ZnSnS4 (CZTS) solar cells: a focus towards efficiency10.1016/j.solener.2018.05.036 ↗
2. Continuous cultivation of microalgae in photobioreactors as a source of renewable energy: current status and future challenges10.1016/j.rser.2021.111852 ↗
3. Cu2ZnSnS4 solar cells with over 10% power conversion efficiency enabled by heterojunction heat treatment10.1038/s41560-018-0206-0 ↗
4. CZTS thin film solar cells on flexible Molybdenum foil by electrodeposition-annealing route10.1007/s10800-020-01494-1 ↗
5. Numerical modeling of AZTS as buffer layer in CZTS solar cells with back surface field for the improvement of cell performance10.1016/j.solener.2021.11.025 ↗
6. Solar cell efficiency tables (version 59)10.1002/pip.3506 ↗
7. The steady rise of kesterite solar cells10.1021/acsenergylett.7b00131 ↗
8. High-efficiency crystalline silicon solar cells: status and perspectives10.1039/C5EE03380B ↗
9. Investigation of spray pyrolyzed cubic structured Cu doped SnS films, Phosphorus, Sulfur Silicon Relat
10. Development of CZTS-based thin film solar cells10.1016/j.tsf.2008.11.002 ↗
11. Preparation and evaluation of Cu2ZnSnS4 thin films by sulfurization of E-B evaporated precursors10.1016/S0927-0248(97)00119-0 ↗
12. New routes to sustainable photovoltaics: evaluation of Cu2ZnSnS4 as an alternative absorber material10.1002/pssb.200879539 ↗
13. Investigation on the sulfurization temperature dependent phase and defect formation of sequentially evaporated Cu-rich CZTS thin films10.1016/j.solener.2020.03.007 ↗
14. Routes to copper zinc tin sulfide Cu2ZnSnS4 a potential material for solar cells10.1039/c2cc30792h ↗
15. Non-vacuum processed next generation thin film photovoltaics: towards marketable efficiency and production of CZTS based solar cells10.1016/j.solener.2013.04.017 ↗
16. Effect of sodium-doping on the performance of CZTS absorb layer: single and bifacial sodium-incorporation method10.1016/j.solener.2021.04.063 ↗
17. Cd-free Cu(in,Ga)(Se,S)2 thin-film solar cell with record efficiency of 23.35%10.1109/JPHOTOV.2019.2937218 ↗
18. A low-temperature order-disorder transition in Cu2ZnSnS4 thin films10.1063/1.4863685 ↗
19. Sentaurus modelling of 6.9% Cu2ZnSnS4 device based on comprehensive electrical & optical characterization10.1016/j.solmat.2016.10.053 ↗
20. Influence of order-disorder in Cu2ZnSnS4 powders on the performance of monograin layer solar cells10.1016/j.tsf.2016.10.017 ↗
21. Properties of Cu2ZnSnS4 films obtained by sulfurization under different sulfur-vapor pressures in a sealed ambient10.1016/j.solener.2021.11.028 ↗
22. Raman and X-ray photoemission identification of colloidal metal sulfides as potential secondary phases in nanocrystalline Cu2ZnSnS4 photovoltaic absorbers10.1021/acsanm.0c00910 ↗
23. Non-stoichiometry effect and disorder in Cu2ZnSnS4 thin films obtained by flash evaporation: Raman scattering investigation10.1016/j.actamat.2013.11.010 ↗
24. Control of secondary phases and disorder degree in Cu2ZnSnS4 films by sulfurization at varied subatmospheric pressures10.1016/j.solmat.2019.109915 ↗
25. Thermoelectric properties of CZTS thin films: effect of Cu-Zn disorder10.1039/D1CP01327K ↗
26. Progress and perspectives of thin film kesterite photovoltaic technology: a critical review10.1002/adma.201806692 ↗
27. Point defects, compositional fluctuations, and secondary phases in non-stoichiometric kesterites10.1088/2515-7655/ab4a25 ↗
28. Device characteristics of CZTSSe thin-film solar cells with 12.6% efficiency10.1002/aenm.201301465 ↗
29. Characterization of a CZTS thin film solar cell grown by sputtering method10.1016/j.solener.2013.11.035 ↗
30. Production and characterization of CZTS films: on the role of H2S flow rate10.1016/j.solener.2019.11.019 ↗
31. Fabrication of 4.9% efficient Cu2ZnSnS4 solar cell using electron-beam evaporated CdS buffer layer10.1016/j.tsf.2019.06.017 ↗
32. Pulsed laser deposited and sulfurized Cu2ZnSnS4 thin film for efficient solar cell10.1016/j.solmat.2021.111383 ↗
33. A high efficiency electrodeposited Cu2ZnSnS4 solar cell10.1002/aenm.201100526 ↗
34. Preparation of high-quality Cu2ZnSnS4 thin films for solar cells via the improvement of sulfur partial pressure using a static annealing sulfurization approach10.1016/j.solmat.2016.05.040 ↗
35. Cu2ZnSnS4 thin films by simple replacement reaction route for solar photovoltaic application10.1016/j.tsf.2013.11.095 ↗
36. Effect of sulfurization temperature on Cu-Zn disorder for non-stoichiometric spray pyrolyzed Cu2ZnSnS4 thin films10.1016/j.matlet.2021.130168 ↗
37. Fabrication of Cu2ZnSnS4 screen printed layers for solar cells10.1016/j.solmat.2010.06.010 ↗
38. Solution processed copper zinc tin sulfide thin films for thermoelectric device applications10.1016/j.ceramint.2020.07.338 ↗
39. Copper-zinc-tin-sulfur thin film using spin-coating technology10.3390/ma9070526 ↗
40. Strong quantum confinement effects in kesterite Cu2ZnSnS4 nanospheres for organic optoelectronic cells10.1039/c3nr03892k ↗
41. Quantitative measurement of preferred orientation in rolled uranium bars
42. Physical properties of transparent and conducting sprayed fluorine doped zinc oxide thin films10.1016/j.solidstatesciences.2007.11.031 ↗
43. Cullity · 1956
44. Kesterites—a challenging material for solar cells10.1002/pip.2156 ↗
45. Fabrication of Cu-rich CZTS thin films by two-stage process: effect of gas flow-rate in sulfurization process10.1016/j.molstruc.2021.129922 ↗
46. Structural, optical and electrical properties of spray-deposited CZTS thin films under a non-equilibrium growth condition10.1088/0022-3727/45/44/445103 ↗
47. Determination of the size and internal structure of colloidal particles using X-rays
48. Williamson-Hall analysis in estimation of lattice strain in nanometer-sized ZnO particles10.1186/2251-7235-6-6 ↗
49. Solar Energy Materials & Solar Cells the crystal structure of kesterite type compounds : a neutron and X-ray diffraction study10.1016/j.solmat.2011.01.002 ↗
50. Structural polymorphism in “kesterite” Cu2ZnSnS4: Raman spectroscopy and first-principles calculations analysis10.1021/acs.inorgchem.6b03008 ↗
51. Crystal and electronic band structure of Cu2ZnSnX4 (X=S and Se) photovoltaic absorbers: first-principles insights
52. Crystal structures of photovoltaic chalcogenides, an intricate puzzle to solve: the cases of CIGSe and CZTS materials10.1002/zaac.201200279 ↗
53. Raman scattering crystalline assessment of polycrystalline Cu2ZnSnS4 thin films for sustainable photovoltaic technologies: phonon confinement model10.1016/j.actamat.2014.02.035 ↗
54. Vibrational properties of stannite and kesterite type compounds: Raman scattering analysis of Cu2(Fe,Zn)SnS410.1016/j.jallcom.2012.06.042 ↗
55. Raman scattering and disorder effect in Cu2ZnSnS410.1002/pssr.201307073 ↗
56. Effect of defects and secondary phases in Cu2ZnSnS4 absorber material on the performance of Zn(O,S) buffered devices10.1016/j.tsf.2018.12.001 ↗
57. Raman Spectroscopy of nanomaterials: how spectra relate to disorder, particle size and mechanical properties10.1016/j.pcrysgrow.2007.01.001 ↗
58. Study of polycrystalline Cu2ZnSnS4 films by Raman scattering10.1016/j.jallcom.2011.04.097 ↗
59. Calculation of the lattice dynamics and Raman spectra of copper zinc tin chalcogenides and comparison to experiments
60. The vibrational properties study of kesterite Cu2ZnSnS4 single crystals by using polarization dependent Raman spectroscopy10.1016/j.optmat.2012.09.031 ↗
61. Secondary phase and Cu substitutional defect dynamics in kesterite solar cells: impact on optoelectronic properties10.1016/j.solmat.2016.01.029 ↗
62. Multiwavelength excitation Raman scattering study of polycrystalline kesterite Cu2ZnSnS4 thin films10.1063/1.4861593 ↗
63. Raman analysis of monoclinic Cu2SnS3 thin films10.1063/1.4712623 ↗
64. Preparation of Cu2SnS3 thin films bySulfurization of Cu/Sn stacked precursors10.7567/JJAP.51.10NC35 ↗
65. Phase-controlled synthesis and photocatalytic properties of SnS , SnS2 and SnS/SnS2 heterostructure nanocrystals10.1016/j.materresbull.2013.02.082 ↗
66. Hexagonal Cu2SnS3 with metallic character : another category of conducting sulfides, 143104-2 Wu Al10.1063/1.2790491 ↗
67. Secondary phases and disorder degree investigation of Cu2ZnSnS4 films10.1016/j.ceramint.2020.09.290 ↗
68. Cross-section analysis of the composition of sprayed Cu2ZnSnS4 thin films by XPS, EDS, and multi-wavelength Raman spectroscopy
69. Cu2ZnSnS4 nanoparticles synthesized via reaction media with glycine10.1016/j.ceramint.2020.10.085 ↗
70. XPS analysis and structural and morphological characterization of Cu2ZnSnS4 thin films grown by sequential evaporation10.1016/j.apsusc.2014.03.124 ↗
71. Synthesis and characterization of Cu2ZnSnS4 thin films grown by PLD : solar cells10.1016/j.jallcom.2011.04.074 ↗
72. XPS analysis and characterization of thin films Cu2ZnSnS4 grown using a novel solution based route10.1016/j.mssp.2015.05.064 ↗
73. The role of copper during the growth of stoichiometric Cu2ZnSnS4 by successive ionic layer adsorption and reaction method10.1016/j.ceramint.2019.10.265 ↗
74. Cu2ZnSnS4 and Cu2ZnSn(S1−xSex)4 nanocrystals: room-temperature synthesis and efficient photoelectrochemical water splitting10.1039/C7TA06628G ↗
75. Development of CZTS thin films solar cells by pulsed laser deposition: influence of pulse repetition rate10.1016/j.solener.2011.03.017 ↗
76. A review on development prospect of CZTS based thin film solar cells10.1155/2014/613173 ↗
77. Photoelectrochemical properties of spray deposited Cu2ZnSnS4 photoelectrode: enhancement in photoconversion efficiency with film thickness
78. Intrinsic point defects in off-stoichiometric Cu2ZnSnSe4 : a neutron diffraction study10.1063/1.4997402 ↗
79. Existence of off-stoichiometric single phase kesterite10.1016/j.jallcom.2015.09.198 ↗
80. Gurieva
81. Review article on the lattice defect and interface loss mechanisms in kesterite materials and their impact on solar cell performance10.1016/j.solener.2021.10.005 ↗
82. Strategic review of secondary phases, defects and defect-complexes in kesterite CZTS-Se solar cells10.1039/C5EE02153G ↗
83. Solid-state NMR and Raman spectroscopy to address the local structure of defects and the tricky issue of the Cu/Zn disorder in Cu-poor, Zn-rich CZTS materials10.1021/ic5012346 ↗
84. 119 Sn MAS NMR to assess the cationic disorder and the anionic distribution in sulfoselenide Cu2ZnSn(SxSe1– x)4 compounds prepared from colloidal and ceramic routes10.1021/acs.jpcc.5b08938 ↗
85. Classification of lattice defects in the kesterite Cu2ZnSnS4 and Cu2ZnSnSe4 earth-abundant solar cell absorbers10.1002/adma.201203146 ↗
86. Influences of rapid thermal annealing on Cu2ZnSnS4 thin film fabricated by spraying approach10.1007/s10854-021-05424-5 ↗
87. Optical properties and electronic structure of Ge10.1002/pssb.19660150224 ↗
88. Pankove · 1975
89. Effect of TaN intermediate layer on the back contact reaction of sputter-deposited Cu poor Cu2ZnSnS4 and Mo10.1016/j.apsusc.2018.11.227 ↗
90. Size control and quantum confinement in Cu2ZnSnS4 nanocrystals10.1039/c1cc14687d ↗
91. Dependence of the properties of copper zinc tin sulfide thin films prepared by electrochemical deposition on sulfurization temperature10.1007/s10854-013-1657-5 ↗
92. Cation disorder in Cu2ZnSnS4 thin films: effect on solar cell performances10.1002/solr.201700101 ↗
93. Band tails and Cu–Zn disorder in Cu2ZnSnS4 solar cells10.1021/acsaem.0c00926 ↗
94. Properties of thermally evaporated CZTS thin films and numerical simulation of earth abundant and non toxic CZTS_Zn(S,O) based solar10.1016/j.solener.2020.06.114 ↗
95. Optical and surface probe investigation of secondary phases in Cu2ZnSnS4 films grown by electrochemical deposition10.1016/j.solmat.2015.03.003 ↗
96. Molecular tunnel junctions based on π -conjugated oligoacene thiols and dithiols between Ag , Au , and Pt contacts : effect of surface linking group and metal work function10.1021/ja207751w ↗
97. Effect of volume of the solution and sulfurization on properties of Cu2ZnSnS4 thin films fabricated by spray assisted chemical vapour deposition method10.1080/14328917.2021.1904627 ↗
98. Effect of deposition temperature on the properties of Cu2ZnSnS4 (CZTS) thin films10.1016/j.spmi.2017.02.003 ↗