journal article·2024-09

Fractal analysis on the surface topography of Monocrystalline silicon wafers sawn by diamond wire

Tengyun Liu, Peirong Zhang, Yancai Su, Yujing Sun

Publisher page

Abstract

The direct impact of diamond wire slicing on the cost of subsequent silicon wafer processing underscores the significance of reducing slicing costs for both the integrated circuit and photovoltaic industries. Effectively and reasonably evaluating monocrystalline silicon wafer quality is thus a crucial challenge. In this paper, fractal theory was used to analyze the monocrystalline silicon wafer sawn surfaces combining with surface roughness measurement. The findings reveal the presence of scratches, pits, and prominent saw marks on the sawn surface. Notably, the surface roughness is significantly higher along the feed direction compared to that along the wire direction. Moreover, an increase in the ratio of feed speed to wire speed leads to a rougher surface. The fractal dimension of the sawn surface is inversely proportional to its roughness, indicating that a higher fractal dimension corresponds to a finer surface texture. Moreover, the two dimensional fractal dimension can effectively capture the anisotropic characteristics of monocrystalline silicon wafers. The two dimensional fractal dimension of the wafer surface obtained by removing materials in ductile mode has a strong symmetry. However, the two dimensional fractal dimension of the surface obtained in brittle mode fluctuates obviously and is weakly symmetric. By combining traditional surface roughness analysis with fractal methods, we can gain insights into the material removal mechanisms involved in slicing monocrystalline silicon wafers using diamond wire, which is of great significance for optimizing diamond wire slicing.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Surface Polishing Techniques · Surface Roughness and Optical Measurements · Adhesion, Friction, and Surface Interactions

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Photovoltaic cell defect classification based on integration of residual-inception network and spatial pyramid pooling in electroluminescence images
2. Study on surface characteristics of as-sawn sapphire crystal wafer considering diamond saw wire wear
3. Effect of the diamond saw wires capillary adhesion on the thickness variation of ultra-thin photovoltaic silicon wafers during slicing10.1016/j.solmat.2023.112525 ↗
4. Modeling and experimental investigation of monocrystalline silicon wafer cut by diamond wire saw10.1016/j.engfracmech.2022.109029 ↗
5. Study on the subsurface damage depth of monocrystalline silicon in ultrasonic vibration assisted diamond wire sawing10.1016/j.engfracmech.2021.108077 ↗
6. Influence of silicon anisotropy on surface shape deviation of wafer by diamond wire saw10.1016/j.mssp.2021.105981 ↗
7. Crack damage control for diamond wire sawing of silicon: the selection of processing parameters10.1016/j.mssp.2022.106838 ↗
8. Research on silicon wafer surface phase under the Ultra-thin slicing process and its etching hindrance behavior during metal-assisted chemical etching
9. An experimental investigation of silicon wafer thinning by sequentially using constant-pressure diamond grinding and fixed-abrasive chemical mechanical polishing10.1016/j.jmatprotec.2021.117453 ↗
10. Image-processing-based model for the characterization of surface roughness and subsurface damage of silicon wafer in diamond wire sawing10.1016/j.precisioneng.2022.06.003 ↗
11. Experiment and theoretical prediction for surface roughness of PV polycrystalline silicon wafer in electroplated diamond wire sawing10.1016/j.jmapro.2019.11.022 ↗
12. Effect of wear of diamond wire on surface morphology, roughness and subsurface damage of silicon wafers10.1016/j.wear.2016.07.009 ↗
13. High surface integrity fabrication of silicon wafers using a newly developed nonwoven structured grind-polishing wheel10.1016/j.jmapro.2022.03.021 ↗
14. Influences of hard inclusions on processing stress in diamond multi-wire sawing multi-crystalline silicon10.1016/j.mssp.2022.106602 ↗
15. Analysis of crack-free surface generation of photovoltaic polysilicon wafer cut by diamond wire saw10.1016/j.solener.2021.01.009 ↗
16. Diamond wire sawing of solar silicon wafers: a sustainable manufacturing alternative to loose abrasive slurry sawing10.1016/j.promfg.2018.02.156 ↗
17. Experiment and theoretical prediction for subsurface microcracks and damage depth of multi-crystalline silicon wafer in diamond wire sawing10.1016/j.engfracmech.2022.108391 ↗
18. Capillary forces as a limiting factor for sawing of ultrathin silicon wafers by diamond multi-wire saw
19. Phase transformation pre-treatment of diamond wire-sawn multi-crystalline silicon wafers for metal-assisted chemical etching of solar cells
20. Characterization of electroplated diamond wires and the resulting workpiece quality in silicon sawing10.1016/j.jmatprotec.2019.116390 ↗
21. Evaluation of fixed abrasive diamond wire sawing induced subsurface damage of solar silicon wafers10.1016/j.jmatprotec.2019.116267 ↗
22. Fundamental investigation of diamond cutting of micro V-shaped grooves on a polycrystalline soft-brittle material
23. The impact of silicon brick polishing on thin (120 μm) silicon wafer sawing yields and fracture strengths in diamond-wire sawing10.1016/j.mssp.2019.104751 ↗
24. Influence of single diamond wire sawing of photovoltaic monocrystalline silicon on the feed force, surface roughness and micro-crack depth
25. Effect of cutting parameters on surface integrity of monocrystalline silicon sawn with an endless diamond wire saw10.1016/j.solener.2020.07.018 ↗
26. Experimental study on brittle–ductile transition in elliptical ultrasonic assisted grinding (EUAG) of monocrystal sapphire using single diamond abrasive grain10.1016/j.ijmachtools.2013.04.004 ↗
27. A novel method for calculating the fractal dimension of three-dimensional surface topography on machined surfaces10.1016/j.chaos.2024.114573 ↗
28. Calculation method for fractal characteristics of machining topography surface based on wavelet transform10.1016/j.procir.2019.02.109 ↗
29. Surface morphology analysis using fractal theory in micro electrical discharge machining10.2320/matertrans.M2016381 ↗
30. Multi-objective optimization of surface morphology using fractal and multi-fractal analysis for dry milling of AISI 434010.1016/j.measurement.2023.113574 ↗
31. Morphological image interpretation of organic nickel(II) phthalocyanine-tetrasulfonic acid tetrasodium film using fractal analysis10.1016/j.apsusc.2014.02.081 ↗
32. The correlation of fractal dimension to fracture surface slope for fatigue crack initiation analysis under bending-torsion loading in high-strength steels10.1016/j.measurement.2023.113169 ↗
33. Fractal analysis of CT images of tight sandstone with anisotropy and permeability prediction10.1016/j.petrol.2021.108919 ↗
34. Surface profile topography of ionic polymer metal composite based on fractal theory
35. Surface integrity in metal machining - Part II: functional performance
36. The influence of wire speed on phase transitions and residual stress in single crystal SiliconWafers sawn by resin bonded DiamondWire saw10.3390/mi12040429 ↗
37. Research on fractal behavior of surface topography in precision grinding on monocrystal sapphire10.3901/JME.2015.19.174 ↗
38. Fractal analysis on machined surface morphologies of soft-brittle KDP crystals processed by micro Ball-End milling10.3390/ma16051782 ↗